Dynomax 39541 Installation guide

Brand: Dynomax

Model: 39541

Type: Installation guide

Below you will find brief information for Exhaust Kit 39541, Inlet Pipe 52613, Resonator 24246, Intermediate Pipe 52612, Muffler Super Turbo 17629, Tail Pipe 55731, Band Clamp 36539, Band Clamp 36438. This document provides step-by-step instructions for installing the DynoMax exhaust system on a 2020 Jeep Gladiator 3.6L. It includes details on removing the OE exhaust components, attaching the new DynoMax parts (including the inlet pipe, resonator, intermediate pipe, muffler, and tail pipe) using band clamps, and ensuring proper alignment.

Below you will find brief information for Exhaust Kit 39541, Inlet Pipe 52613, Resonator 24246, Intermediate Pipe 52612, Muffler Super Turbo 17629, Tail Pipe 55731, Band Clamp 36539, Band Clamp 36438. This document provides step-by-step instructions for installing the DynoMax exhaust system on a 2020 Jeep Gladiator 3.6L. It includes details on removing the OE exhaust components, attaching the new DynoMax parts (including the inlet pipe, resonator, intermediate pipe, muffler, and tail pipe) using band clamps, and ensuring proper alignment.

2701 N. Dettman Rd.

Jackson, MI 49201

INSTALLATION INSTRUCTIONS FOR

DynoMax Kit: 39541

2020 Jeep Gladiator 3.6L

DANGER WARNING: SHOULD THE PURCHASER DECIDE TO INSTALL

ANY EXHAUST PRODUCT AT HOME, BE WARNED THAT PASSENGER

CAR OR LIGHT DUTY TRUCK/VAN BUMPER JACKS ARE INTENDED

FOR EMERGENCY USE ONLY. THE USE OF FRAME CONTACT JACK

STANDS, IN CONJUNCTION WITH A FLOOR JACK AS MAIN SUPPORT,

IS HIGHLY RECOMMENDED TO MINIMIZE ACCIDENTAL DROPPING OF

A VEHICLE DURING THE INSTALLATION PROCESS.

NOTE: Read all instructions before starting any work.

1. Remove the OE inlet pipe/mufer/tail pipe assembly from the vehicle.

Lubricate the rubber isolators with WD-40, or a similar product, to aid in

removal of the metal rod hangers from the rubber isolators.

2. Install DynoMax front exhaust pipe 52613. Slightly tighten the reusable

OE clamp or use included clamp 36539 on the front exhaust pipe.

Please see the system diagram.

3. Place a 36438 band clamp on the inlet end and install DynoMax Bullet

resonator 24246. Slightly tighten the inlet clamp at the connection to

the front pipe.

4. Place a 36438 band clamp on the inlet end and install DynoMax

intermediate pipe 52612. Insert the metal rod hanger into the rubber

isolator on the chassis. Slightly tighten the clamp to the resonator

outlet.

5. Place a 36438 band clamp on the inlet end and install 17629 Super

Turbo mufer. Please reference the system diagram. Slightly tighten the

inlet clamp.

6. Place a 36438 band clamp on the inlet end and install tail pipe 55731.

Install the metal rod hangers into the rubber isolators on the chassis.

7. Beginning at the inlet end, align the exhaust system components and

fully tighten all the clamps.

8. Please see the system diagram on the back page of these instructions.

KIT CONTAINS:

(1) 52613 Inlet Pipe

(1) 24246 Resonator

(1) 52612 Intermediate Pipe

(1) 17629 Super Turbo Mufﬂer

(1) 55731 Tail Pipe

(1) 36539 Band Clamp

(4) 36438 Band Clamp

(1) Instruction Sheet

Form: 82609862

08/2019

39541 SYSTEM DIAGRAM

Form: 82609862

08/2019

52613 24246 52612

2Z\x" Clamp 2Z\x" Clamp 2Z\x" Clamp

2Z\x" Clamp 2Z\x" Clamp

17629

55731

1
2

Dynomax 39541 Installation guide

Brand: Dynomax

Model: 39541

Type: Installation guide

Below you will find brief information for Exhaust Kit 39541, Inlet Pipe 52613, Resonator 24246, Intermediate Pipe 52612, Muffler Super Turbo 17629, Tail Pipe 55731, Band Clamp 36539, Band Clamp 36438. This document provides step-by-step instructions for installing the DynoMax exhaust system on a 2020 Jeep Gladiator 3.6L. It includes details on removing the OE exhaust components, attaching the new DynoMax parts (including the inlet pipe, resonator, intermediate pipe, muffler, and tail pipe) using band clamps, and ensuring proper alignment.

Download PDF

Related papers

Other documents