Corsa Performance 21062 Installation guide

Brand
Corsa Performance
Model
21062
Type
Installation guide

This manual is also suitable for

140 Blaze Industrial Pkwy, Berea, OH 44017 l Toll Free: 1.800.486.0999 l Fax: 440.891.1868 l www.corsaperformance.com
20 JEEP
Gladiator 3.6L
IMPORTANT! WARRANTY AND
INSTALLATION INSTRUCTIONS
Please Forward All Information to Consumer
Be sure to review the enclosed instructions prior to beginning the installation process. If you have any
questions about the enclosed parts or instructions, or if you encounter a problem during installation:
CALL TECHNICAL SUPPORT: 440.891.0999 or 800.486.0999
COLOR INSTRUCTIONS ARE AVAILABLE BY PART NUMBER ON: CORSAPERFORMANCE.COM
NEVER work on a hot exhaust system.
Allow time for the vehicle to cool.
Always wear eye protection
when working under a vehicle.
INSTALL DIFFICULTY
RECOMMENDED TOOLS & SUPPLIES
• 3/8” Drive Ratchet
• Grommet Pullers
• 3/8” Drive 10mm Socket
• Soap and Water Solution
• 3/8” Drive 13mm Deep Socket
• Torque Wrench
• 3/8” Drive 15mm Deep Socket
• Chain Cutter
• 3/8” Drive 21mm Deep Socket
• Safety Glasses
TO ACTIVATE YOUR WARRANTY GO TO:
CORSAPERFORMANCE.COM/WARRANTY
INS5371
2
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
Please take time to read and understand these installation instructions.
CORSA recommends that the installation of this system be performed by a qualified service center or
professional installer who has the necessary equipment, tools, and experienced personnel. However, if you
decide to perform this installation yourself, the use of an additional person may be required.
WARNING: Never work on a hot exhaust system. Allow time for the vehicle to cool. Always wear eye
protection when working under a vehicle.
CORSA Performance makes no representation or warranty, expressed or implied that its downpipe or header
products and or components there-in comply with federal, state or local emission levels, noise levels, or safety
standards or that any of their parts conform with the racing vehicles exemption, unless otherwise noted. The
purchaser assumes all responsibility for such use and compliance.
This warranty does not extend to damaged or defect in the finish of a product or to any product, that in the
opinion of CORSA Performance, has been misused, damaged by accident or negligence, altered or modified in
any way, faulty installation or installed contrary to CORSA installation instructions, or repaired by an
unauthorized service facility.
Full warranty available on www.corsaperformance.com
Please confirm that all parts are present according to the bill of materials before beginning the installation.
If something is missing call Tech Support at 440.891.099 or Toll Free: 1.800.486.0999
BILL OF MATERIALS
1.
Headpipe Assembly (28JT4000)
2.
Muffler Assembly (28JT2000)
3.
Mid Pipe Assembly (Sport Only) (28JT4008)
4.
Pack Muffler Assembly (Touring Only) (28JT2004)
5.
Single Side Exit Tail Pipe Assembly (28JT4013)
6.
Tip Assembly (25TC3000)
7.
Hardware Kit (18DR7033)
Single Side Exit
Sport – 21060(BLK)
Touring – 21062(BLK)
INS5371
3
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
BILL OF MATERIALS
1.
Headpipe Assembly (28JT4000)
2.
Muffler Assembly (28JT2000)
3.
Mid Pipe Assembly (Sport Only) (28JT4008)
4.
Pack Muffler Assembly (Touring Only) (28JT2004)
5.
Dump Exit Tail Pipe Assembly (28JT4013)
6.
Hardware Kit (20FF7026)
Dump Style Exit
Sport – 21061
Touring – 21063
INS5371
4
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
CAUTION: Never work on a hot exhaust system. Allow the vehicle to cool for at least an hour and a half. Always wear eye
protection when working under a vehicle. It is recommended to use cotton gloves in order to protect stainless steel
surfaces from permanent grease and oil stains.
REMOVAL INSTRUCTIONS
FACTORY EXHAUST
There are two methods for removing the factory exhaust. The first method is to remove the
exhaust system in one piece (Steps 1-8). The second method requires cutting the factory
exhaust into two pieces and may be necessary when not using a vehicle lift (Steps 9-).
METHOD 1
1. Locate your vehicles tire tool kit and lower the
spare tire
2. Using a 10mm socket and ratchet, remove the
two bolts on the inside of the spare tire shield.
3. Using a 10mm socket and ratchet remove the
two nuts and one bolt on the front side of the
spare tire heat shield. Remove the heat shield
from the vehicle. Save shield and hardware for
installation.
4. To create more room for the removal of the stock
exhaust, the track bar will need to be lowered on
the driver side. Using a 21mm socket and ratchet
remove the bolt securing the track bar.
Continued on Next Page . . .
INS5371
5
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
REMOVAL INSTRUCTIONS
FACTORY EXHAUST
5. Remove the bolt and backing nut and lower the
track bar. Save hardware for installation.
6. Using a 13mm socket and ratchet, unfasten the
rear hanger isolator. Isolator and mounting
hardware will be re-used for installation.
7. Using 13mm socket and ratchet, loosen clamp
attaching stock inlet pipe to catalytic converter.
NOTE: Clamp will be used for installation.
8. Slide entire exhaust to the rear of the vehicle to
remove hangers from isolators and to clear
brace. Remove entire exhaust from vehicle.
NOTE: A soap and water solution may aid in
removal of hangers from rubber isolators.
9. Replace track bar, tightening hardware to factory specs. Re-install heat shield and spare tire.
Continued on Next Page . . .
INS5371
6
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
REMOVAL INSTRUCTIONS
FACTORY EXHAUST
Method 2
10. Locate the indent in the pipe approximately 2.5”
behind the muffler and before the middle hanger.
Using a chain cutter, cut the stock exhaust at this
indent.
11. Using a 13mm socket and ratchet, unfasten the
rear hanger isolator. Isolator and mounting
hardware will be re-used for installation.
Slide the rear section of the factory exhaust
from the middle rubber isolator and remove the
rear section of the factory exhaust through the
rear of the vehicle.
NOTE: A soap and water solution may aid in
removal of hangers from rubber isolators.
12. Using 13mm socket and ratchet, loosen clamp
attaching stock inlet pipe to catalytic converter.
NOTE: Save clamp for installation.
13. Slide the front section of the factory exhaust
from the front rubber isolator and remove the
front section of the exhaust from the vehicle.
NOTE: A soap and water solution may aid in
removal of hangers from rubber isolators.
Step 12 concludes the removal of the factory exhaust.
INS5371
7
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
WARNING! DO NOT SKIP THIS STEP!
Apply the anti-seize lubricant (supplied) to the threads
ONLY of all the clamps and flange bolts. Failure to follow
this procedure can cause nuts to seize on clamps and
potentially destroy threads.
After applying anti-seize lubricant, be sure to thoroughly
clean your hands, as lubricant will tarnish stainless steel.
All clamps should be tightened using a properly calibrated
Torque Wrench. Using an air impact gun will damage the
clamp and reduce its ability to effectively seal the joint. It
may also cause the joint to separate, thereby causing
damage to your exhaust system and to your vehicle.
NOTE: Align all clamps so that the center of the clamp bolt is 90 degrees from the notch in the pipe.
INSTALLATION INSTRUCTIONS
CORSA EXHAUST
1. Locate headpipe assembly and factory spherical clamp from removal step 7 or 12 depending on removal
method. Push spherical inlet of headpipe onto factory exhaust and cover joint with clamp. Snug clamp
using 13mm socket and ratchet.
Continued on Next Page . . .
INS5371
8
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
2. Locate muffler assembly and one 3” clamp.
3. Slide muffler assembly onto headpipe outlet with
3” clamp and snug clamp with 15mm socket and
ratchet, supporting outlet end of muffler.
4. Locate mid pipe assembly for sport exhaust or pack muffler assembly for touring exhaust and one 3”
clamp. Slide hanger into rubber isolator.
NOTE: The use of a soap and water solution may ease the installation of hanger.
5. Slide midpipe inlet onto outlet of muffler and snug clamp using a 15mm socket and ratchet.
Continued on Next Page . . .
INS5371
9
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
INSTALLATION INSTRUCTIONS
CORSA EXHAUST
DUMP VERSION
Single Side Exit
6. Locate the tailpipe assembly and the rear rubber isolator mounting bracket from removal step 6 or 11
depending on removal method. Install rubber isolator onto rear hanger of tailpipe.
NOTE: The use of a soap and water solution may ease the installation of hanger into rubber
isolator.
7. Feed the tailpipe assembly over the axle from
the rear of the vehicle. Insert the hanger into the
rubber isolator.
NOTE: The use of a soap and water solution
may ease the installation of hanger into
rubber isolator.
8. Locate one 3” clamp and place it on the inlet of
the tailpipe. Insert the outlet of the midpipe into
the inlet of the tailpipe.
Continued on Next Page . . .
INS5371
10
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
INSTALLATION INSTRUCTIONS
CORSA EXHAUST
Dump Version
Single Side Exit
9. Secure the rubber isolator mounting bracket to its factory location using the hardware from removal step
6 or 10. Tighten the bracket hardware using a 13mm socket and ratchet.
10. Tighten the clamp connecting the tailpipe to the
mid pipe assembly using a ratchet and 15mm
socket until the tailpipe is snug on the mid pipe.
11. For Single Side Exit systems, locate tip assembly
and 3” clamp. Slide tip assembly onto tailpipe
along with clamp and position tip to desired etch
reveal.
12. Moving from the front of the vehicle to the rear, ensure there is sufficient clearance to all components
and tighten all clamps to 45 ft/lbs using torque wrench and 13mm socket for front clamp and 15mm
socket for remaining clamps.
Step 12 completes the installation of your CORSA Exhaust System
INS5371
11
12/3/2019
2020 Jeep Gladiator 3.6L
3.0” Cat-Back Exhaust
Part #: 21060(BLK), 21061, 21062(BLK), 21063
NOTE: During cold weather start-ups, you may experience an exhaust sound that is deeper and louder in
tone than usual. This is temporary and will diminish to normal levels once your engine has reached its
normal operating temperature.
NOTE: Immediately following the installation of your exhaust system, you may experience a trace of smoke
after initial start-up. DO NOT be alarmed. The smoke is caused by the burning of a small amount of forming
oil residue used in the manufacturing process.
NOTE: It is strongly suggested that all clamps be checked and tightened after road testing the vehicle once
the system has cooled.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Corsa Performance 21062 Installation guide

Brand
Corsa Performance
Model
21062
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents