3-37 Unlocking the Dual Processor Module Locking Mechanism.......................................................79
3-38 Aligning the Processor Module.....................................................................................................80
3-39 Locking the Dual Processor Module in Place................................................................................80
3-40 Sliding the Sequencing Retainer Plate...........................................................................................81
3-41 Securing the Captive Screws.........................................................................................................81
3-42 Power Module Shims....................................................................................................................82
3-43 Aligning the Processor Module Power Pod..................................................................................82
3-44 Installing the Processor Module Power Pod Mounting Screws....................................................83
3-45 Connecting the Power Pod Cable..................................................................................................84
3-46 Routing the Turbofan Power Cables through Heatsink Posts......................................................84
3-47 Replacing the System Battery........................................................................................................86
3-48 LAN Ports on the Server Rear.......................................................................................................89
3-49 iLO MP Setup Flowchart...............................................................................................................91
3-50 Web GUI Login Page.....................................................................................................................98
3-51 Status Summary Page....................................................................................................................99
3-52 Control Panel LEDs and Buttons.................................................................................................107
5-1 Control Panel LEDs.....................................................................................................................118
5-2 Location of the STBY and BMC LEDs.........................................................................................120
6-1 Internal Physical Layout..............................................................................................................124
6-2 System Board Connectors and Slots............................................................................................125
6-3 Release the Rack Latches.............................................................................................................127
6-4 Removing the Top Cover on a Rack-Mounted Server.................................................................128
6-5 Aligning the Top Cover on a Rack-Mounted Server...................................................................128
6-6 Closing the Top Cover on a Rack-Mounted Server.....................................................................129
6-7 Front Bezel Retaining Clip...........................................................................................................129
6-8 Replacing the Front Bezel on a Rack-Mounted Server................................................................130
6-9 Removing the Side Cover on a Pedestal-Mounted Server..........................................................131
6-10 Removing the Top Cover on a Pedestal-Mounted Server...........................................................132
6-11 Top Cover Alignment Mark........................................................................................................133
6-12 Replacing the Top Cover on a Pedestal-Mounted Server............................................................133
6-13 Replacing the Side Cover on a Pedestal-Mounted Server...........................................................134
6-14 Removing the Front Bezel on a Pedestal-Mounted Server..........................................................135
6-15 Aligning the Pedestal Front Bezel...............................................................................................135
6-16 Removing Fan 1A or Fan 1B........................................................................................................137
6-17 Removing Fan 2...........................................................................................................................137
6-18 Removing Fan 3...........................................................................................................................137
6-19 Releasing the Power Supply Retaining Clip................................................................................139
6-20 Removing the Power Supply.......................................................................................................139
6-21 Replacing the Power Supply.......................................................................................................140
6-22 Unlocking the Disk Drive............................................................................................................141
6-23 Releasing the Disk Drive.............................................................................................................141
6-24 Removing the Disk Drive............................................................................................................142
6-25 Removing the Disk Drive Slot Filler............................................................................................143
6-26 Installing the Hard Disk Drive....................................................................................................143
6-27 Airflow Guides Locations............................................................................................................144
6-28 Removing the Memory Airflow Guide.......................................................................................145
6-29 Removing the Processor Airflow Guide......................................................................................146
6-30 Opening the Release Clip............................................................................................................147
6-31 Removing the Front Portion of the Processor Airflow Guide ....................................................147
6-32 Routing Power Cables Through Heatsink Posts.........................................................................149
6-33 DIMM Slot Identification.............................................................................................................150
6-34 Inserting the DIMM Into the Connector Socket..........................................................................154
6-35 Disconnecting the Power Pod Cable............................................................................................155
6-36 Removing the Power Pod Mounting Screws...............................................................................156
6-37 Disconnecting the Power Pod From the Dual Processor Module...............................................156
11