Indicator description:
System Indicator:SYS
Green LED Bl ink Working normal
OFF Working abnormal or powered off
PoE Indicator:PoE
Green LED ON C onnect with PD, and working normal
Port short circuit or o ver current
Green LED Bl ink
OFF No PD connected or not supply power
Indicator:Link
Yellow LED ON Data under transmiss ion
Yellow LED Blink Connected and data un der transmission
OFF No netwo rk device conne cted
Indicator Status D escription
Note:Please confirm that the all the PD devices are complying with IEEE802.3af/at standard.
!
Power Industrial Terminals: 48 (48 ~ 57V)VDC , dual redundanc y ( More than 5 0VDC recommended when use d PoE+
output), please use AC1 00~240V, 50/60 Hz power su pply;
PoE Port: The PoE ports support PoE fun ction, which can transmit d ata and pow er simultaneou sly if conn ected matching
device. The LED lights on the front pan el can show working status of e ach port.
Ethernet Port: besid e PoE port, o ther ports are Ethernet RJ4 5 port, and all RJ45 port suppo rt Auto MD IMDIX, pl ug and
play.Th e LED lights on the front panel c an show working status of eac h port.
Please install with the supporting devices.
Please confirm the following things before installation:
1. If the POE port meets the power requirement of the connecting devices.
2. If the POE standard requirement and power supply matches with the power receiving device
(1/2+、3/6-( End -span)/ 4/5+、7/8-(Mid-span))
3 .If the output power of the matched power adapter is compatible with the specification in the label of the POE switch
Please install the POE switch according to the following steps:
1. Put the PoE switch on the surface of a large and stable table.
2. Plug the power adapter into the power connector, and then connect the power outlet through the power cord.
3. Connect the network devices to the POE switch port though network cable.
Note:
1.Please do not put heavy products on the POE switch, and please ensure good ventilation environment for
the POE switch.
2.Please cut off the power first before plugging the power adapter.
Connect the power cable, plug it into power socket, turn on the power, then the switch will automatically initialize,
and LED lights status will display as following:
1.Except the POE port lights, all the other lights will go through the process of “on-off-on-off”, which means the
estoration is successful.
2.Power LED remains lit.
Installation guide
!
!
Connection Diagram Model Descriptions
Tel:+8 6-755-33376 606 Fax:+86-7 55-33376608 E mail:onv@on v.com .cn
Addr ess: Room 1003, B lock D , Terra building , C hegongmiao, F utian distric t ,Shenzhen ,Ch ina
Fact ory address:N o 5, A building, Se nYuTai S&T park, Longhua r oad, BaoAn dist rict,Shenzh en, China
www.onv.com.cn
ONV-IPS33064PFM:
Industrial Ethernet PoE Switch, 4x 10/100/1000M PoE Ports, 2x Gigabit Optical Ports. PoE port is compatible with
IEEE802.3af/at, max power for each port is 30W. It also support SNMP Management Protocol. The RJ45 transmission
distance is 100m, the SFP optical port transmission distance is 2-120km. The power adaptor and SFP module are not included.
Uplink Gigabit SFP
Optical Port
Green LED ON D ata under trans mission
Connected and data under transmission
Green LED Bl ink
OFF No data co nnected.
6-Port 10/100/1000M
Managed Switch
Industr ial
PoE
Switch
IPS33 064PFM
Wide Area N etwork
Note:
If initialization is inconsistent with the above, please check the power.
Power