2. WinSystems
  3. PXM-MINIPCIE-G

WinSystems PXM-MINIPCIE-G User manual

  • Hello! I am an AI chatbot trained to assist you with the WinSystems PXM-MINIPCIE-G User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
WinSystems, Inc.
715 Stadium Drive
Arlington, TX 76011
http://www.winsystems.com
WinSystems
®
PXM-MiniPCIe
SUMIT-ISM
Module with MiniPCIe and USB
PRODUCT MANUAL
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 2
P/N 400-0368-000
Date Code REV Level ECO Number
100422 A
REVISION HISTORY
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 3
TABLE OF CONTENTS
Visual Index - Top View (Connectors) 5
Visual Index - Top View (Jumpers & LEDs) 6
Visual Index - Bottom View (Connectors & Jumpers) 7
Jumper Reference 8
INTRODUCTION 11
FEATURES 11
System 11
FUNCTIONALITY 12
MiniPCIe Cards 12
RF Connectors 12
Status Indicators 12
User Indentity Module (UIM) Connector 12
CONNECTOR REFERENCE 13
POWER 13
D2 (Power LED +5VSB), D1 (Power LED +5V) 13
USB 13
J8, J9 - USB 13
PC/104 BUS INTERFACE 14
J16 - PC/104 14
SUMIT
TM
INTERFACE 15
J1, J2 - SUMIT 15
MiniPCI EXPRESS 16
J11 - MiniPCIe 16
CABLES 17
SOFTWARE DRIVERS & EXAMPLES 18
MECHANICAL DRAWING 19
APPENDIX 20
WARRANTY INFORMATION 21
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 4
This page has been left intentionally blank.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 5
Visual Index - Top View (Connectors)
NOTE: The reference line to each component part has been drawn to Pin 1, and is also highlighted with a square, where applicable.
RESERVED - D7, D8
J16
PC/104 (C/D)
J1
SUMIT-A
J12
MiniPCIe
Antennae
J13
MiniPCIe
Antennae
J7
SIM Card
J2
SUMIT-B
J16
PC/104 (A/B)
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 6
Visual Index - Top View (Jumpers & LEDs)
NOTE: The reference line to each component part has been drawn to Pin 1, and is also highlighted with a square, where applicable.
RESERVED - D7, D8
D3
PCIExpress
Status Indicator 2
D5
PCIExpress
Status Indicator 3
D4
USB0 Power
D9
USB1 Power
D7
D6
PCIExpress
Status Indicator 1
J5
USB2 Power
J15
J11
MiniPCIe Socket
J14
J4
USB (0/1)
J9
USB3 (2.0)
J8
USB2 (2.0)
J3
W_Disable
D2
Power LED
+5VSB
D1
Power LED
+5V
J10
USB (1/3)
J6
USB (0/2)
D8
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 7
Visual Index - Bottom View (Connectors & Jumpers)
NOTE: The reference line to each component part has been drawn to Pin 1, and is also highlighted with a square, where applicable.
RESERVED - D7, D8
J101
J100
J101
SD100
J100
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 8
Jumper Reference
Jumpering Options to be determined.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 9
Jumper Reference (cont’d)
Jumpering Options to be determined.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 10
This page has been left intentionally blank.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 11
INTRODUCTION
This manual is intended to provide the necessary information regarding conguration and usage of the PXM-MiniPCIe
SUMIT-ISM module. WinSystems maintains a Technical Support Group to help answer questions not adequately
addressed in this manual. Contact Technical Support at (817) 274-7553, Monday through Friday, between 8 AM and 5
PM Central Standard Time (CST).
FEATURES
SUMIT™ Interface
Revision 1.5
MiniPCIe
Full and Half size PCIe mini card support
PCIe and USB 2.0 interface support through SUMIT AB
Multiple antennae support (via 2 RF connectors)
SIM card socket
Power
Onboard power supplies
USB
2 USB 2.0 ports
Overcurrent and inrush protection for each port
Automatic USB signal lane shifting
LED status provided for each port
Industrial Operating Temperature
-40°C to 85°C
Form Factor
3.6” x 3.8” (90 mm x 96 mm)
Standard
RoHS compliant
PC/104 and SUMIT expansion connectors
Activity status LEDs on-board
PS/2 Keyboard and Mouse
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
System
The PXM-MiniPCIe is a SUMIT-ISM module that supports both a MiniPCIe card and two USB ports. It provides expansion
of additional functions such as 802.11a/g wireless, WLAN, and othe rhigh performance functions developed for mobile
computing environments. The two USB 2.0 expansion ports support tethered aplications such as storage, imaging, and
video, as well as slower dvices such as mouse, keyboard, oppy disk, USB keys, etc.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 12
FUNCTIONALITY
MiniPCIe Cards
The MiniCard is a small form factor board used to implement the PCI Express interface on notebook computers for
additional I/O functions. The PCI Express MiniCard socket supports two primary system bus interfaces: PCI Express x1
and USB 2.0, and provides connections to many other functions.
RF Connectors
Two right angle RF connectors are on the PXM-MiniiPCIe board’s edge, enabling convenient connection to the MiniPCIe
card from a regular coax cable from an external antenna.
Status Indicators
Three inidividual LEDs provide a visual status of the installed wireless card’s function.
User Indentity Module (UIM) Connector
A UIM contains parameters necessary for the WWAN device’s operation in a wireless wide area radio environment.
The W_DISABLE# signal is supported to disable radio operation. This signal is wired to a connector on the edge of the
PXM-MiniPCIe module.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 13
CONNECTOR REFERENCE
POWER
Visual
Index
The +5V input power and ground is supplied from the SUMIT A and B, and PC/104 connectors, located at J1, J2, and
J16, respectively. There is a +5V to 3.3V regulator and a +5V to 1.5V regulator on-board to supply power to MiniPCIe
cards. Power is applied to the PXM-MiniPCIe via the connector at J15.
LEDs located at D2 (Power LED +5VSB), D1 (Power LED +5V) indicate the state of the system.
NOTE: D2 and D1 will always be illuminated during normal operation. When using an ATX power supply and only D2 is
illuminated, the system is in suspend mode.
D2 (Power LED +5VSB), D1 (Power LED +5V)
Visual
Index
D2 GREEN +5VSB
D1 RED VCC (+5V)
USB
Up to two USB cables may be attached to the PXM-MiniPCIe via the connectors for a total of four USB 2.0
ports. These are terminated to an 8-pin, 2 mm connector at J8 and J9. An adapter cable CBL-356-G-1-1.0 is
available from WinSystems for connection. Two additional USB ports are available for expansion on the SUMIT™
interface.
USBPWR1
D1-
D1+
GND
□ □
□ □
□ □
□ □
2
4
6
8
J8
1
3
5
7
USBPWR0
D0-
D0+
GND
J8, J9 - USB
Visual
Index
USBPWR3
D3-
D3+
GND
□ □
□ □
□ □
□ □
2
4
6
8
J9
1
3
5
7
USBPWR2
D2-
D2+
GND
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 14
PC/104 BUS INTERFACE
NOTES:
1. Rows C and D are not required on 8-bit modules.
2. B10 and C19 are key locations. WinSystems uses key pins as connections to GND.
3. Signal timing and function are as specied in ISA specication.
4. Signal source/sink current differ from ISA values.
# = Active Low Signal
The PC/104 bus is electrically equivalent to the 16-bit ISA bus. Standard PC/104 I/O cards can be populated on
PXM-MiniPCIe’s connectors, located at J16. The interface does not support hot swap capability. The PC/104 bus
connector pin denitions are provided here for reference. Refer to the PC/104 Bus Specication for specic signal and
mechanical specications.
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
J16
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
GND
MEMCS16#
IOCS16#
IRQ10
IRQ11
IRQ12
IRQ15
IRQ14
DACK0#
DRQ0
DACK5#
DRQ5
DACK6#
DRQ6
DACK7#
DRQ7
+5V
MASTER#
GND
GND
GND
SBHE#
LA23
LA22
LA21
LA20
LA19
LA18
LA17
MEMR#
MEMW#
SD8
SB9
SD10
SD11
SD12
SD13
SD14
SD15
KEY
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
J16
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
IOCHK#
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
IOCHRDY
AEN
SA19
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
GND
GND
RESET
+5V
IRQ
-5V
DRQ2
-12V
SRDY#
+12V
KEY
SMEMW#
SMEMR#
IOW#
IOR#
DACK3#
DRQ3
DACK1#
DRQ1
REFRESH#
BCLK
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
DACK2#
TC
BALE
+5V
OSC
GND
GND
J16 - PC/104
Visual
Index
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 15
SUMIT
TM
INTERFACE
The PXM-MiniPCIe has a SUMIT-A connector which allows for multiple I/O modules to be stacked on top of a host
module. SUMIT-A is located at J1. A second SUMIT-B connector, located at J2. Their pinouts for J1 and J2 are
listed above. Refer to the SUMIT Specication for more information on the SUMIT Interface.
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
J1
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
5V
3.3V_1
3.3V_2
EXPCD_REQ#
EXPCD_PRSNT#
USB_OC#0/1
USB_OC#0/1
5V_2
USB3+
USB3-
5V_3
USB2+
USB2-
5V_4
USB1+
USB1-
5V_5
USB0+
USB0-
GND_1
A_PETp0
A_PETn0
GND_2
PERST#
WAKE#
5V_6
12V
SMB_DATA
SMB_CLK
SMB_ALERT
SPI_DO
SPI_DI
SPI_CLK
SPI_CS0
SPI_CS1
RESERVED_5
LPC_DRQ
LPC_AD0
LPC_AD1
LPC_AD2
LPC_AD3
LPC_FRAME#
SERIRQ#
LPC_PRSNT#/GND
CLK_33MHz
GND_3
A_PERp0
A_PERn0
APRSNT
A_CLKp
A_CLKn
GND_4
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
J2
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
5V
B_PETp0
B_PETn0
GND
C_CLKp
C_CLKn
CPRSNT#/GND
C_PETp0
C_PETn0
GND_2
C_PETp1
C_PETn1
GND
C_PETp2
C_PETn2
GND_3
C_PETp3
C_PETn3
GND_4
PERST#
RESERVED
5V_2
RV_3
5V_4
5V_5
5V_6
GND
B_PERp0
B_PERn0
BPRST#/GND
B_CLKp
B_CLKn
GND
C_PERp0
C_PERn0
GND
C_PERp1
C_PERn1
GND
C_PERp2
C_PERn2
GND
C_PERp3
C_PERn3
GND
WAKE#
RESERVED
RESERVED
3.3V
3.3V_2
3.3V_3
5V_7
J1, J2 - SUMIT
Visual
Index
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 16
MiniPCI EXPRESS
The PXM-MiniPCIe includes a MiniPCIExpress socket at J11. Though the socket can support other devices, it is
most often used to add wireless Ethernet cards from Broadcom
®
, Foxconn
®
, (Atheros), or others.
NOTE: Intel
®
boards are not supported by the PXM-MiniPCIe.
Pin Name Pin Name
2 3
.3Vaux 1 WAKE#
4 GND 3 COEX1
6 1.5V 5 COEX2
8 UIM_PWR 7 CLKREQ#
10 UIM_DATA 9 GND
12 UIM_CLK 11 REFCLK-
14 UIM_RESET 13 REFCLK+
16 UIM_VPP 15 GND
Mechanical Key
18 GND 17 Reserved (UIM_C8)
20 W_DISABLE# 19 Reserved (UIM_C4)
22 PERST# 21 GND
24 +
3.3Vaux 23 PERn0
26 GND 25 PERp0
28 +1.5V 27 GND
30 SMB_CLK 29 GND
32 SMB_DATA 31 PETn0
34 GND 33 PETp0
36 USB_D- 35 GND
38 USB_D+ 37 GND
40 GND 39 +
3.3Vaux
42 LED_WWAN# 41 +
3.3Vaux
44 LED_WLAN# 43 GND
46 LED_WPAN# 45 Reserved
48 +1.5V 47 Reserved
50 GND 49 Reserved
52 +
3.3Vaux 51 Reserved
J11 - MiniPCIe
Visual
Index
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 17
CABLES
Cables to be determined.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 18
SOFTWARE DRIVERS & EXAMPLES
Software Drivers & Examples to be determined.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 19
MECHANICAL DRAWING
Mechanical Drawing to be determined.
Preliminary
100422 PRODUCT MANUAL PXM-MiniPCIe 20
BIOS
PXM-MiniPCIe BIOS See WinSystems website.
Ethernet Driver
(Drivers for 10/100/1000 Ethernet Controller)
Examples
(For WS16C48 Compatible Digital I/O Chip)
DOS Driver - C Functions uio48ebc.zip
Linux Drivers - Kernel 2.2, 2.4 linux_uio48_96.zip
Linux Drivers - Kernel 2.6 uio48io_kernel_2.6.zip
Windows XP Driver wsuio48_96xp.zip
(Counter Timer Demo)
Reprogramming DOS tick for high resolution timing tickdemo.zip
Serial Console Utilities
Serial Console Client wincom.zip
APPENDIX
To be included in later manual versions.
Preliminary
/