WinSystems PPM-WIRELESS is designed to provide high-speed wireless connectivity for industrial applications. It supports 802.11b/g wireless communications using miniPCI modules from Intel, Broadcom, Atheros, and others. With an operating temperature range of -40°C to 85°C, it is suitable for harsh environments. The PPM-WIRELESS is a PC/104-Plus compliant module with a 3.60 in x 3.80 in form factor, enabling easy integration into existing systems. It features an onboard 3.3V regulator, allowing operation with +5V boards.
WinSystems PPM-WIRELESS is designed to provide high-speed wireless connectivity for industrial applications. It supports 802.11b/g wireless communications using miniPCI modules from Intel, Broadcom, Atheros, and others. With an operating temperature range of -40°C to 85°C, it is suitable for harsh environments. The PPM-WIRELESS is a PC/104-Plus compliant module with a 3.60 in x 3.80 in form factor, enabling easy integration into existing systems. It features an onboard 3.3V regulator, allowing operation with +5V boards.
OPERATIONS MANUAL
PPM-WIRELESS
NOTE: This manual has been designed and created for use as part of the WinSystems’ Technical Manuals
CD and/or the WinSystems’ web site. If this manual or any portion of the manual is downloaded, copied
or emailed, the links to additional information (i.e. software, cable drawings) will be inoperable.
WinSystems reserves the right to make changes in the circuitry
and specications at any time without notice.
Copyright 2008 by WinSystems. All Rights Reserved.
REVISION HISTORY
P/N 403-0304-000B
ECO Number Date Code Rev Level
ORIGINATED 041008 A
07-142 080107 A.1
08-144 080917 A.2
09-51 090623 A.3
Table of Contents
Visual Index – Quick Reference i
Top View - Connectors and Jumpers i
Introduction 1
General Information 1
Features 1
Functional Capability 2
Conguration Options 2
miniPCI Device Interface (J5) 3
Software 4
RF Antenna Connection 4
Wireless Network Architecture 4
miniPCI Device Interrupt Conguration (J1) 4
PC/104-Plus Bus Slot Selection (J9) 5
PC/104-Plus Bus Interface (J4) 5
PC/104 Bus Interface (J8) 6
On-board Voltage Regulator (J10) 7
Development Kit 7
Jumper Reference 8
Mechanical Drawing 10
Specications 11
WARRANTY REPAIR INFORMATION 12
090623 OPERATIONS MANUAL PPM-WIRELESS i
Visual Index – Quick Reference
Top View - Connectors and Jumpers
For the convenience of the user, a copy of the Visual Index has been provided with
direct links to connector and jumper conguration data.
NOTE: The reference line to each component part has been drawn to Pin 1, where applicable.
Pin 1 is also highlighted with a red square, where applicable.
J7
Auxiliary
Antenna
J9
PC/104-Plus Bus
Slot Selection
4 o o 2
3 o o 1
J1
miniPCI Device
Interrupt
2 o o 1
4 o o 3
J3
Main Antenna
Cable
J2
Main Antenna
J8
PC/104 Bus
Connector
J6
Auxiliary
Antenna Cable
J10
Voltage
Selection
2 o o 1
4 o o 3
J4
PC/104-Plus Bus
Connector
J5
miniPCI Device
Interface
090623 OPERATIONS MANUAL PPM-WIRELESS 1
This manual is intended to provide the necessary information regarding conguration and
usage of the PPM-WIRELESS board. WinSystems maintains a Technical Support Group to help
answer questions regarding usage, or programming of the board. For answers to questions not
adequately addressed in this manual, contact Technical Support at (817) 274-7553 between
8 A.M. and 5 P.M. Central Standard Time.
Wireless Module
IEEE 802.11 module supported
Supports Intel, Broadcom, Atheros, and similar miniPCI modules
Power
Onboard 3.3V regulator (allows +5V board operation)
Industrial Operating Temperature Range
-40°C to 85°C
Form Factor
PC/104-Plus-compliant
3.60 in x 3.80 in (90 mm x 96 mm)
•
•
•
•
•
•
General Information
Introduction
Features
WinSystems PPM-WIRELESS is a PC/104-Plus module that supports 802.11b/g wireless
communications. This technology provides a high-speed, industrial data network based upon
miniPCI wireless modules and Ethernet utilizing a TCP/IP protocol stack. This means that
the standard CAT5 Ethernet cable is replaced by a radio channel which simplies cabling
installation and conguration issues. Lack of cabling makes moves, additions, and changes
easy for installed networks. Also, the portable nature of wireless networks lets engineers pre-
congure and troubleshoot entire networks before installing them at remote locations. Once
congured, a system can be moved from place to place with little or no modication.
Applications include high bandwidth remote communications, MPEG video streaming,
mobile environments, remote surveillance, and protocol conversion.
WARNING: Compliance with Part 15 of the FCC rules is fully the
responsibility of the customer.
090623 OPERATIONS MANUAL PPM-WIRELESS 2
The PPM-Wireless is shipped with an empty miniPCI socket (J5) so that a user can
install their own cards from Intel
®
, Broadcom, Foxconn (Atheros), and others. It is also
available in a kit which includes an Intel
®
PRO/Wireless 2200BG mini-PCI card installed
by WinSystems.
An Intel PRO/Wireless 2200BG card is a standards-based, Wi-Fi Certied wireless local
area network (WLAN) solution that allows up to 54 million bits of data to be transferred
per second. It is designed to maintain high throughput at longer ranges depending upon
the type of antenna used. The Intel PRO/Wireless 2200BG is software upgradeable to
provide future security and other service enhancements. The Intel PRO/Wireless 2200BG
network connection fully supports today’s security standards such as Wi-Fi Protected
Access (WPA) and can be upgraded via software downloads for future security standards
such as when 802.11i becomes available.
Functional Capability
Conguration Options
Visual
Index
The PPM-WIRELESS is a small, PC/104-Plus compliant module that measures only 3.60 in
x 3.80 in (90 mm x 96 mm). The PPM-Wireless can be stacked on top of a host PC/104-
Plus, EPIC, or EBX single board computer. On board the PPM-WIRELESS are the interface
electronics, a miniPCI connector, power supply, and antenna connector.
WinSystems’ PPM-WIRELESS converts the PC/104-Plus PCI signals into miniPCI-compatible
signals. A miniPCI card is a small version of a standard desktop PCI card with the same
features and functionality of a normal PCI card but at about one quarter the size. Ideally
suited for embedded applications, the miniPCI card measures only 51 mm x 60 mm. The
PPM-WIRELESS supports the same miniPCI cards used worldwide in laptop computers. The
operating temperature range -40°C to 85°C does not apply to the user-populated mini-PCI
card.
090623 OPERATIONS MANUAL PPM-WIRELESS 3
Visual
Index
PIN SIGNAL PIN SIGNAL PIN SIGNAL PIN SIGNAL
1 TIP 2 RING 63 3.3V 64 FRAME
KEY KEY 65 CLKRUN# 66 TRDY#
3 8PMJ-3 4 8PMJ-1 67 SERR# 68 STOP#
5 8PMJ-6 6 8PMJ-2 69 GROUND 70 3.3V
7 8PMJ-7 8 8PMJ-4 71 PERR# 72 DEVSEL#
9 8PMJ-8 10 8PMJ-5 73 C/BE(1)# 74 GROUND
11 LED_GRN+ 12 LED_YEL+ 75 AD(14) 76 AD(15)
13 LED_GRN- 14 LED_YEL- 77 GROUND 78 AD(13)
15 CHSGND 16 RESERVED 79 AD(12) 80 AD(11)
17 INTB# 18 5V 81 AD(10) 82 GROUND
19 3.3V 20 INTA# 83 GROUND 84 AD(09)
21 RESERVED 22 RESERVED 85 AD(08) 86 C/BE(0)#
23 GROUND 24 3.3V AUX 87 AD(07) 88 3.3V
25 CLK 26 RST# 89 3.3V 90 AD(06)
27 GROUND 28 3.3V 91 AD(05) 92 AD(04)
29 REQ# 30 GNT# 93 RESERVED 94 AD(02)
31 3.3V 32 GROUND 95 AD(03) 96 AD(00)
33 AD(31) 34 PME# 97 5V 98 RESERVED_WIP
5
35 AD(29) 36 RESERVED 99 AD(01) 100 RESERVED_WIP
5
37 GROUND 38 AD(30) 101 GROUND 102 GROUND
39 AD(27) 40 3.3V 103 AC_SYNC 104 M66EN
41 AD(25) 42 AD(28) 105 AC_SRDATA_IN 106 AC_SDATA_OUT
43 RESERVED 44 AD(26) 107 AC_BIT_CLK 108 AC_CODEC_ID0#
45 C/BE(3)# 46 AD(24) 109 AC_CODEC_ID1# 110 AC_RESET#
47 AD(23) 48 IDSEL 111 MON_AUDIO_MON 112 RESERVED
49 GROUND 50 GROUND 113 AUDIO_GND 114 GROUND
51 AD(21) 52 AD(22) 115 SYS_AUDIO_OUT 116 SYS_AUDIO_IN
53 AD(19) 54 AD(20) 117 SYS_AUDIO_OUT_GND 118 SYS_AUDIO_IN_GND
55 GROUND 56 PAR 119 AUDIO_GND 120 AUDIO_GND
57 AD(17) 58 AD(18) 121 RESERVED 122 MPCIACT#
59 C/BE(2)# 60 AD(16) 123 VCC5VA 124 3.3VAUX
61 IRDY# 62 GROUND
# = ACTIVE LOW SIGNAL
miniPCI Device Interface (J5)
090623 OPERATIONS MANUAL PPM-WIRELESS 4
Visual
Index
RF Antenna Connection
The PPM-WIRELESS has a reverse polarized (RP) SMA external connector to enable the
selection of an antenna having characteristics best suited for the application. Typical
indoor range for an omni-directional is 100 ft (30m) @ 54 Mbps or 300 ft (91m) @ 1
Mbps; however, it is dependent upon the type and placement of the antenna, and any
sources of interference in the environment.
The most common antenna type for wireless LANs is omni-directional, but some
applications may require directional radiation patterns. A second RF connector can be
added to the PPM-WIRELESS board as a factory option to support a diversity antenna
conguration for improved performance.
Software
Normally 802.11 cards are automatically recognized by operating systems such as Windows
®
XP. The individual miniPCI card manufacturer will typically have drivers available with their card
and/or at their website. Please contact them directly for specic operating systems that their
card will support.
Users need very little new information to take advantage of wireless LANs (WLAN).
Because the wireless nature of a WLAN is transparent to a user’s network operating
system (NOS), applications work the same as they do on LANs using cables. The
802.11 protocol can be deployed in ad hoc mode for peer-to-peer communication
between wireless stations or in “infrastructure mode” enabling communication
between stations and access points (APs).
Wireless Network Architecture
Visual
Index
miniPCI Device Interrupt Conguration (J1)
J1 congures device interrupts for the miniPCI interface. When a ‘Single Function’
miniPCI device is present, J1 should be jumpered 1-2. For ‘Dual Function’ devices,
jumper J1 1-2 and 3-4.
2 o o 1
4 o o 3
2 o o 1
4 o o 3
Single function miniPCI
device
Dual function miniPCI
device
J1
J1
090623 OPERATIONS MANUAL PPM-WIRELESS 5
PC/104-Plus Bus Slot Selection (J9)
The PPM-WIRELESS provides a high-performance, 32-bit PCI interface using the
PC/104-Plus bus. Multiple PC/104-Plus boards can be installed and supported on a
single stack.
J9 is used to select the “slot” number of the PCI connection for the board. Each
PC/104-Plus board installed in a system must have a unique slot assignment and must
not conict with any PCI slot assignments on the CPU card.
The jumper settings for J9 are shown here:
4 o o 2
3 o o 1
SLOT 1
4 o o 2
3 o o 1
SLOT 3
4 o o 2
3 o o 1
SLOT 2
4 o o 2
3 o o 1
SLOT 4
There is also a PC/104 connector on the PPM-WIRELESS board to support mixed
PC/104 and PC/104-Plus modules on a stack. No control or data signals are wired to
the PC/104 connector. It simply feeds the signals through the connector to the next
module in a stack.
PIN A B C D
1 GND RESERVED +5V AD00
2 VI/O AD02 AD01 +5V
3 AD05 GND AD04 AD03
4 C/BE0# AD07 GND AD06
5 GND AD09 AD08 GND
6 AD11 VI/O AD10 M66EN
7 AD14 AD13 GND AD12
8 +3.3V C/BE1# AD15 +3.3V
9 SERR# GND RESERVED PAR
10 GND PERR# +3.3V RESERVED
11 STOP# +3.3V LOCK# GND
12 +3.3V TRDY# GND DEVSEL#
13 FRAME# GND IRDY# +3.3V
14 GND AD16 +3.3V C/BE2#
15 AD18 +3.3V AD17 GND
16 AD21 AD20 GND AD19
17 +3.3V AD23 AD22 +3.3V
18 IDSEL0 GND IDSEL1 IDSEL2
19 AD24 C/BE3# VI/O IDSEL3
20 GND AD26 AD25 GND
21 AD29 +5V AD28 AD27
22 +5V AD30 GND AD31
23 REQ0# GND REQ1# VI/O
24 GND REQ2# +5V GNT0#
25 GNT1# VI/O GNT2# GND
26 +5V CLK0 GND CLK1
27 CLK2 +5V CLK3 GND
28 GND INTD# +5V RST#
29 +12V INTA# INTB# INTC#
30 -12V REQ3# GNT3# GND/3.3V KEY
# = ACTIVE LOW SIGNAL
Visual
Index
PC/104-Plus Bus Interface (J4)
Visual
Index
090623 OPERATIONS MANUAL PPM-WIRELESS 6
Visual
Index
J8 PC/104 BUS CONNECTOR
PC/104 Bus Interface (J8)
# = Active Low Signal
NOTES:
1. Rows C and D are not required on 8-bit modules.
2. B10 and C19 are key locations. WinSystems uses key pins as connections to GND.
3. Signal timing and function are as specied in ISA specication.
4. Signal source/sink current differ from ISA values.
D0 o o C0
D1 o o C1
D2 o o C2
D3 o o C3
D4 o o C4
D5 o o C5
D6 o o C6
D7 o o C7
D8 o o C8
D9 o o C9
D10 o o C10
D11 o o C11
D12 o o C12
D13 o o C13
D14 o o C14
D15 o o C15
D16 o o C16
D17 o o C17
D18 o o C18
D19 o o C19
GND
MEMCS16#
IOCS16#
IRQ10
IRQ11
IRQ12
IRQ15
IRQ14
DACK0#
DRQ0
DACK5#
DRQ5
DACK6#
DRQ6
DACK7#
DRQ7
+5V
MASTER#
GND
GND
GND
SBHE#
LA23
LA22
LA21
LA20
LA19
LA18
LA17
MEMR#
MEMW#
SD8
SD9
SD10
SD11
SD12
SD13
SD14
SD15
KEY
A1 o o B1
A2 o o B2
A3 o o B2
A4 o o B4
A5 o o B5
A6 o o B6
A7 o o B7
A8 o o B8
A9 o o B9
A10 o o B10
A11 o o B11
A12 o o B12
A13 o o B13
A14 o o B14
A15 o o B15
A16 o o B16
A17 o o B17
A18 o o B18
A19 o o B19
A20 o o B20
A21 o o B21
A22 o o B22
A23 o o B23
A24 o o B24
A25 o o B25
A26 o o B26
A27 o o B27
A28 o o B28
A29 o o B29
A30 o o B30
A31 o o B31
A32 o o B32
GND
RESET
+5V
IRQ9
-5V
DRQ2
-12V
SRDY#
+12V
KEY
SMEMW#
SMEMR#
IOW#
IOR#
DACK3#
DRQ3
DACK1#
DRQ1
REFRESH#
BCLK
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
DACK2#
TC
BALE
+5V
OSC
GND
GND
IOCHK#
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
IOCHRDY
AEN
SA19
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
GND
090623 OPERATIONS MANUAL PPM-WIRELESS 7
Visual
Index
On-board Voltage Regulator (J10)
An on-board 3.3V regulator allows the board to be used with either +5V or 3.3V
PC/104-Plus processor boards. J10 routes the voltage sources supplied from the
PC/104-Plus bus to the on-board Vcc circuit. Refer to the jumpering options shown below
to route the appropriate voltage. When the supplied voltage from the PC/104-Plus bus
connector is +3.3V, connecting J10 pins 2-4 routes +3.3V directly to the PPM-WIRELESS
Vcc circuit. When +5V are supplied, jumpering pins 1-2 routes +5V to an on-board DC
regulator, which converts the +5V source to +3.3V for Vcc.
Development Kit
A development kit is available that includes the PPM-WIRELESS, Intel miniPCI 802.11 b/g
module, antenna, and cables. It provides a reliable, quick start kit to use during initial product
design.
Additional information about this kit and available software drivers is listed on the WinSystems’
website www.winsystems.com.
Most miniPCI wireless cards will require 3.3 VDC to be provided for proper operation. The
PPM-WIRELESS card can provide this 3.3 VDC supply voltage either directly from the
PC/104-Plus 3.3 VDC supply or by using the 5 VDC supply from the PC/104-Plus bus and
regulating the supply down to 3.3 VDC through an on-board regulator. Jumper J10 is used
to make this selection. Jumpering options based on either the +5V or +3.3V operation are
provided above.
2 o o 1
4 o o 3
2 o o 1
4 o o 3
+5V
+3.3V
J10
J10
090623 OPERATIONS MANUAL PPM-WIRELESS 8
Jumper Reference
Drawings Only - for more detailed informaiton on these parts, refer to the
descriptions shown previously in this manual.
NOTE: The reference line to each component part has been drawn to Pin 1, where applicable.
Pin 1 is also highlighted with a red square, where applicable.
J7
Auxiliary
Antenna
J9
PC/104-Plus Bus
Slot Selection
4 o o 2
3 o o 1
J1
miniPCI Device
Interrupt
2 o o 1
4 o o 3
J3
Main Antenna
Cable
J2
Main Antenna
J8
PC/104 Bus
Connector
J6
Auxiliary
Antenna Cable
J10
Voltage
Selection
2 o o 1
4 o o 3
J4
PC/104-Plus Bus
Connector
J5
miniPCI Device
Interface
090623 OPERATIONS MANUAL PPM-WIRELESS 9
PC/104-Plus Bus Slot Selection (J9)
J9 is used to select the “slot” number of the PCI connection for the board.
4 o o 2
3 o o 1
SLOT 1
4 o o 2
3 o o 1
SLOT 3
4 o o 2
3 o o 1
SLOT 2
4 o o 2
3 o o 1
SLOT 4
Onboard Voltage Regulator (J10)
When the supplied voltage from the PC/104-Plus bus connector is +3.3V, connecting J10
pins 2-4 routes +3.3V directly to the PPM-WIRELESS Vcc circuit. When +5V are supplied,
jumpering pins 1-2 routes +5V to an on-board DC regulator, which converts the +5V
source to +3.3V for Vcc.
2 o o 1
4 o o 3
2 o o 1
4 o o 3
+5 V
+3.3 V
J10
J10
miniPCI Device Interrupt Conguration (J1)
When a ‘Single Function’ miniPCI device is present, J1 should be jumpered 1-2. For ‘Dual
Function’ devices, jumper J1 1-2 and 3-4.
4 o o 2
3 o o 1
4 o o 2
3 o o 1
Single function miniPCI
device
Dual function miniPCI
device
J1
J1
090623 OPERATIONS MANUAL PPM-WIRELESS 10
Mechanical Drawing
090623 OPERATIONS MANUAL PPM-WIRELESS 11
Electrical
Power Requirements :VCC +5V
Mechanical
Dimensions :3.6 in x 3.8 in (90 mm x 96 mm)
Weight :3.0 oz (84 grams) approximate weight
Connectors
RF :RP-SMA
miniPCI :124-pin, 0.8 mm
PC/104-Plus :120-pin (4 x 30;2 mm) stackthrough with
shrouded header
PC/104 :16-bit stackthrough (feed through only)
Environmental
Operating Temperature :-40°C to 85°C
Non-condensing relative
Humidity :5% to 95%
MTBF :....
Specications
090623 OPERATIONS MANUAL PPM-WIRELESS 12
WARRANTY REPAIR INFORMATION
WARRANTY
(http://www.winsystems.com/company/warranty.cfm)
WinSystems warrants to Customer that for a period of two (2) years from the date of
shipment any Products and Software purchased or licensed hereunder which have been
developed or manufactured by WinSystems shall be free of any material defects and shall
perform substantially in accordance with WinSystems’ specications therefore. With respect
to any Products or Software purchased or licensed hereunder which have been developed or
manufactured by others, WinSystems shall transfer and assign to Customer any warranty
of such manufacturer or developer held by WinSystems, provided that the warranty, if any,
may be assigned. Notwithstanding anything herein to the contrary, this warranty granted by
WinSystems to the Customer shall be for the sole benet of the Customer, and may not be
assigned, transferred or conveyed to any third party. The sole obligation of WinSystems for
any breach of warranty contained herein shall be, at its option, either (i) to repair or replace
at its expense any materially defective Products or Software, or (ii) to take back such Products
and Software and refund the Customer the purchase price and any license fees paid for the
same. Customer shall pay all freight, duty, broker’s fees, insurance charges for the return of
any Products or Software to WinSystems under this warranty. WinSystems shall pay freight
and insurance charges for any repaired or replaced Products or Software thereafter delivered
to Customer within the United States. All fees and costs for shipment outside of the United
States shall be paid by Customer. The foregoing warranty shall not apply to any Products of
Software which have been subject to abuse, misuse, vandalism, accidents, alteration, neglect,
unauthorized repair or improper installations.
THERE ARE NO WARRANTIES BY WINSYSTEMS EXCEPT AS STATED HEREIN, THERE ARE NO
OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN NO EVENT
SHALL WINSYSTEMS BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES
INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF DATA, PROFITS OR GOODWILL.
WINSYSTEMS’ MAXIMUM LIABILITY FOR ANY BREACH OF THIS AGREEMENT OR OTHER CLAIM
RELATED TO ANY PRODUCTS, SOFTWARE, OR THE SUBJECT MATTER HEREOF, SHALL NOT
EXCEED THE PURCHASE PRICE OR LICENSE FEE PAID BY CUSTOMER TO WINSYSTEMS FOR
THE PRODUCTS OR SOFTWARE OR PORTION THEREOF TO WHICH SUCH BREACH OR CLAIM
PERTAINS.
WARRANTY SERVICE
1. To obtain service under this warranty, obtain a return authorization number. In the
United States, contact the WinSystems’ Service Center for a return authorization number.
Outside the United States, contact your local sales agent for a return authorization number.
2. You must send the product postage prepaid and insured. You must enclose the products
in an anti-static bag to protect from damage by static electricity. WinSystems is not responsible
for damage to the product due to static electricity.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
WinSystems PPM-WIRELESS is designed to provide high-speed wireless connectivity for industrial applications. It supports 802.11b/g wireless communications using miniPCI modules from Intel, Broadcom, Atheros, and others. With an operating temperature range of -40°C to 85°C, it is suitable for harsh environments. The PPM-WIRELESS is a PC/104-Plus compliant module with a 3.60 in x 3.80 in form factor, enabling easy integration into existing systems. It features an onboard 3.3V regulator, allowing operation with +5V boards.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WinSystems PPM-GIGABIT-G User manual
-
-
-
-
-
-
-
-
-
