Canon i-SENSYS MF211 Series User manual

Category
Fax machines
Type
User manual
87654321
i-SENSYS MF229dw/MF226dn/MF217w/
MF216n/MF212w/MF211 Series
Service Manual Rev.1.0
Product Overview
Technical Overview
Periodical Services
Disassembly/Assembly
Adjustment
Trouble Shooting
Error Codes
Service Mode
Appendix
0
0
0-2
0-2
Application
This manual has been issued by Canon Inc. for qualied persons to learn technical theory,
installation, maintenance, and repair of products. This manual covers all localities where the
products are sold. For this reason, there may be information in this manual that does not
apply to your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements
or changes in products. When changes occur in applicable products or in the contents of this
manual, Canon will release technical information as the need arises. In the event of major
changes in the contents of this manual over a long or short period, Canon will issue a new
edition of this manual.
The following paragraph does not apply to any countries where such provisions are
inconsistent with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks
of the individual companies.
Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
not be copied, reproduced or translated into another language, in whole or in part, without the
consent of Canon Inc.
Copyright CANON INC. 2014
Caution
Use of this manual should be strictly supervised to avoid disclosure of condential
information.
0
0
0-3
0-3
Explanation of Symbols
The following symbols are used throughout this Service Manual.
Symbols Explanation Symbols Explanation
Check.
1x
Remove the claw.
Check visually.
1x
Insert the claw.
Check a sound. Push the part.
1x
Disconnect the connector. Connect the power cable.
1x
Connect the connector.
Disconnect the power
cable.
1x
Remove the cable/wire
from the cable guide or wire
saddle.
Turn on the power.
1x
Install the cable/wire to the
cable guide or wire saddle.
Turn off the power.
1x
Remove the screw.
1x
Loosen the screw.
1x
Install the screw.
1x
Tighten the screw.
Symbols Explanation Symbols Explanation
Cleaning is needed. Measurement is needed.
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specic functions and the
relationship between electrical and mechanical systems with reference to the timing of
operation.
In the diagrams, represents the path of mechanical drive; where a signal name
accompanies the symbol, the arrow
indicates the direction of the electric signal.
The expression "turn on the power" means ipping on the power switch, closing the front
door, and closing the delivery unit door, which results in supplying the machine with power.
2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is "High",
while '0' is used to indicate "Low". (The voltage value, however, differs from circuit to
circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD signal goes on
when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked
in the eld. Therefore, the operations of the microprocessors used in the machines are not
discussed: they are explained in terms of from sensors to the input of the DC controller
PCB and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product
improvement or other purposes, and major changes will be communicated in the form of
Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service
Manual and all relevant Service Information bulletins and be able to identify and isolate faults
in the machine.
0
Safety Precautions
CDRH Provisions -------------------------------------------------------------0-2
Laser Safety
--------------------------------------------------------------------0-2
About Laser Beams --------------------------------------------------------------- 0-2
Handling Laser Scanner Unit --------------------------------------------------- 0-2
Toner Safety --------------------------------------------------------------------0-3
About Toner ------------------------------------------------------------------------- 0-3
Handling Adhered Toner --------------------------------------------------------- 0-3
Notes on Handling Lithium Battery ---------------------------------------0-3
Notes on Assembly/Disassembly
-----------------------------------------0-3
1
Product Overview
Product Lineups ---------------------------------------------------------------1-2
Main Unit ----------------------------------------------------------------------------- 1-2
Options ------------------------------------------------------------------------------- 1-2
Manufacture Sketch Drawing ----------------------------------------------1-3
Features
-------------------------------------------------------------------------1-4
Features ------------------------------------------------------------------------------ 1-4
Product Specications -------------------------------------------------------1-4
Main Unit Specications ---------------------------------------------------------- 1-4
Wireless LAN Specications ---------------------------------------------------- 1-6
SADF/DADF Specications ----------------------------------------------------- 1-6
FAX Specications(FAX model Only) ----------------------------------------- 1-7
Name of Parts ------------------------------------------------------------------1-8
External View ----------------------------------------------------------------------- 1-8
Cross Section ---------------------------------------------------------------------- 1-11
Control Panel ----------------------------------------------------------------------1-13
Contents
2
Technical Overview
Basic Conguration -----------------------------------------------------------2-2
Conguration function ------------------------------------------------------------ 2-2
Basic Sequence -------------------------------------------------------------------- 2-2
Controller System -------------------------------------------------------------2-4
Main Controller --------------------------------------------------------------------- 2-4
Engine Controller ------------------------------------------------------------------ 2-4
Service Works ---------------------------------------------------------------------- 2-5
Document Exposure/Feeder System ------------------------------------2-6
Document Exposure System ---------------------------------------------------- 2-6
Document Feeder System ------------------------------------------------------- 2-7
Service Works ---------------------------------------------------------------------2-10
Laser Exposure System --------------------------------------------------- 2-11
Overview ---------------------------------------------------------------------------- 2-11
Controlling the Laser Activation Timing --------------------------------------2-12
Laser Control -----------------------------------------------------------------------2-13
Laser Scanner Motor Control --------------------------------------------------2-13
Service Works ---------------------------------------------------------------------2-14
Image Formation System ------------------------------------------------- 2-15
Overview/Conguration ---------------------------------------------------------2-15
High-Voltage Control -------------------------------------------------------------2-19
Toner Cartridge --------------------------------------------------------------------2-20
Service Works ---------------------------------------------------------------------2-22
Fixing System ---------------------------------------------------------------- 2-23
Overview/Conguration ---------------------------------------------------------2-23
Various Control Mechanisms --------------------------------------------------2-24
Other Functions -------------------------------------------------------------------2-25
Service Works ---------------------------------------------------------------------2-26
Pickup And Feeding System --------------------------------------------- 2-27
Overview ----------------------------------------------------------------------------2-27
Detecting Jams --------------------------------------------------------------------2-28
Reversal Delay Jam --------------------------------------------------------------2-30
Service Works ---------------------------------------------------------------------2-33
External And Controls System ------------------------------------------- 2-34
Power Supply ----------------------------------------------------------------------2-34
Service Works ---------------------------------------------------------------------2-35
3
Periodical Services
Periodically Replaced Parts ------------------------------------------------3-2
Periodically Replaced Parts ----------------------------------------------------- 3-2
Consumables ------------------------------------------------------------------3-2
Consumables ----------------------------------------------------------------------- 3-2
Periodical Service -------------------------------------------------------------3-3
Scheduled Servicing -------------------------------------------------------------- 3-3
4
Disassembly/Assembly
Outline ---------------------------------------------------------------------------4-3
List of Parts
---------------------------------------------------------------------4-4
External View ----------------------------------------------------------------------- 4-4
List of Main Unit
-------------------------------------------------------------------- 4-7
Electrical Components -----------------------------------------------------------4-10
Connectors Layout Drawing ---------------------------------------------- 4-19
DADF Unit and Reader Unit ----------------------------------------------------4-19
SADF Unit and Reader Unit ----------------------------------------------------4-20
Copyboard Unit and Reader Unit ---------------------------------------------4-21
Duplex Printer Unit ---------------------------------------------------------------4-22
Sinplex Printer Unit ---------------------------------------------------------------4-25
Original Exposure/Feed System (DADF Model) -------------------- 4-27
Layout Drawing --------------------------------------------------------------------4-27
Removing the DADF Unit + Reader Unit -----------------------------------4-27
Disconnecting the DADF Unit + Reader Unit ------------------------------4-30
Removing the DADF Pickup Unit ---------------------------------------------4-32
Removing the DADF Motor Unit ----------------------------------------------4-36
Removing the DADF Solenoid Unit ------------------------------------------4-38
Removing the DADF Pickup Roller Unit ------------------------------------4-39
Removing the DADF Separation Pad ----------------------------------------4-41
Removing the Copyboard Glass (DADF Model) --------------------------4-44
Removing the Contact Image Sensor (DADF Model)
-------------------4-46
Removing the Flat Bed Motor Unit (DADF Model) -----------------------4-48
Original Exposure/Feed System (SADF Model) --------------------- 4-51
Layout Drawing --------------------------------------------------------------------4-51
Removing the SADF Unit + Reader Unit. -----------------------------------4-51
Disconnecting the SADF Unit and the Reader Unit ----------------------4-54
Removing the SADF Upper Cover Unit -------------------------------------4-56
Removing the SADF Pickup Unit ---------------------------------------------4-60
Removing the SADF Motor -----------------------------------------------------4-61
Removing the SADF Pickup Roller Unit -------------------------------------4-62
Removing the SADF Separation Pad ----------------------------------------4-65
Removing the Copyboard Glass (SADF Model) --------------------------4-68
Removing the Contact Image Sensor (SADF Model)--------------------4-70
Removing the Flat Bed Motor Unit (SADF Model)------------------------4-72
Original Exposure/Feed System (Copyboard Model) -------------- 4-75
Layout Drawing --------------------------------------------------------------------4-75
Removing the Copyboard Cover ----------------------------------------------4-75
Removing the Copyboard Cover + Reader Unit --------------------------4-76
Removing the Copyboard Glass (Copyboard Model)--------------------4-78
Removing the Contact Image Sensor (Copyboard Model) -------------4-80
Removing the Flat Bed Motor Unit (Copyboard Model) -----------------4-82
External Cover/Internal System (Duplex Model) -------------------- 4-85
Layout Drawing --------------------------------------------------------------------4-85
Removing the Left Cover (Duplex Model) ----------------------------------4-86
Removing the Right Cover (Duplex Model) --------------------------------4-87
Removing the Front Cover Unit (Duplex Model) --------------------------4-89
Removing the Upper Cover Unit (Duplex Model) -------------------------4-89
Removing the Duplex Feed Guide Unit. (Duplex Model) ---------------4-91
Controller System (Duplex Model) -------------------------------------- 4-93
Layout Drawing --------------------------------------------------------------------4-93
Removing the Control Panel Unit (Duplex Model) ------------------------4-93
Removing the Main Motor (Duplex Model) ---------------------------------4-95
Removing the Main Fan (Duplex Model) ------------------------------------4-97
Removing the Edge Left Cooling Fan (Duplex Model) ------------------4-99
Removing the Edge Right Cooling Fan (Duplex Model) -------------- 4-101
Removing the Engine Controller PCB (Duplex Model) ---------------- 4-102
Removing the Main Controller PCB (Duplex Model) ------------------- 4-105
Removing the FAX NCU PCB
(Fax Model 120V/230V) (Duplex Model) ---------------------------------- 4-107
Removing the Wirelss LAN PCB (Wi Model + Duplex Model) ----- 4-108
Removing the Paper Leading Edge Sensor PCB (Duplex Model) - 4-108
Removing the Fixing Delivery/Paper Width Sensor PCB
(Duplex Model) -------------------------------------------------------------------4-111
Removing the Toner Sensor and Multi Pickup Sensor Unit
(Fax Model + Duplex Model) ------------------------------------------------- 4-114
Removing the Speaker (Fax Model + Duplex Model) ----------------- 4-116
Laser Exposure System (Duplex Model) -----------------------------4-118
Layout Drawing ------------------------------------------------------------------ 4-118
Removing the Laser Scanner Unit (Duplex Model) -------------------- 4-118
Image Formation System (Duplex Model) -------------------------- 4-120
Layout Drawing ------------------------------------------------------------------ 4-120
Removing the Transfer Roller (Duplex Model) -------------------------- 4-120
Fixing System (Duplex Model) ----------------------------------------- 4-122
Layout Drawing ------------------------------------------------------------------ 4-122
Removing the Fixing Assembly (Duplex Model) ------------------------ 4-122
Pickup Feed System (Duplex Model) -------------------------------- 4-127
Layout Drawing ------------------------------------------------------------------ 4-127
Removing the Pickup Unit (Duplex Model) ------------------------------- 4-127
Removing the Pickup Tray Unit (Duplex Model) ------------------------ 4-132
Removing the Pickup Roller (Duplex Model) ---------------------------- 4-134
Removing the Separation Pad (Duplex Model) ------------------------- 4-135
Removing the Delivery Slave Roller Unit (Duplex Model) ------------ 4-136
Removing the Pickup Solenoid (Duplex Model)------------------------- 4-137
Removing the Duplex Solenoid (Duplex Model) ------------------------ 4-141
External Cover/Internal System (Simplex Model) ----------------- 4-143
Layout Drawing ------------------------------------------------------------------ 4-143
Removing the Left Cover (Simplex Model) ------------------------------- 4-144
Removing the Right Cover (Simplex Model) ----------------------------- 4-145
Removing the Front Cover Unit (Simplex Model) ----------------------- 4-147
Removing the Upper Cover (Simplex Model) ---------------------------- 4-147
Removing the Rear Cover (Simplex Model) ----------------------------- 4-149
Controller System (Simplex Model) ---------------------------------- 4-151
Layout Drawing ------------------------------------------------------------------ 4-151
Removing the Control Panel Unit (Simplex Model) -------------------- 4-151
Removing the Main Motor (Simplex Model) ------------------------------ 4-153
Removing the Engine Controller PCB (Simplex Model)--------------- 4-155
Removing the Main Controller PCB (Simplex Model) ----------------- 4-159
Removing the FAX NCU PCB
(Fax Model 120V/230V + Simplex Model) -------------------------------- 4-161
Removing the Wireless LAN PCB (Wi Model + Simplex Model) -- 4-161
Removing the Paper Leading Edge Sensor (Simplex Model) ------- 4-162
Removing the Fixing Delivery/Paper Width Sensor PCB
(Simplex Model) ----------------------------------------------------------------- 4-164
Removing the Toner Sensor and Multi Pickup Sensor Unit
(Fax Model + Simplex Model) ----------------------------------------------- 4-167
Removing the Speaker (Fax Model + Simplex Model) ---------------- 4-169
Laser Exposure System (Simplex Model) -------------------------- 4-171
Layout Drawing ------------------------------------------------------------------ 4-171
Removing the Laser Scanner Unit (Simplex Model) ------------------- 4-171
Image Formation System (Simplex Model) ------------------------- 4-173
Layout Drawing ------------------------------------------------------------------ 4-173
Removing the Transfer Roller (Simplex Model) ------------------------- 4-173
Fixing System (Simplex Model) --------------------------------------- 4-175
Layout Drawing ------------------------------------------------------------------ 4-175
Removing the Fixing Assembly (Simplex Model) ----------------------- 4-175
Pickup Feed System (Simplex Model) ------------------------------- 4-180
Layout Drawing ------------------------------------------------------------------ 4-180
Removing the Pickup Unit (Simplex Model) ------------------------------ 4-180
Removing the Pickup Tray Unit (Simplex Model) ----------------------- 4-184
Removing the Pickup Roller (Simplex Model) --------------------------- 4-186
Removing the Separation Pad (Simplex Model) ------------------------ 4-187
Removing the Delivery Slave Roller Unit (Simplex Model) ----------- 4-188
Removing the Pickup Solenoid (Simplex Model) ----------------------- 4-190
5
Adjustment
Mechanical Adjustment ------------------------------------------------------5-2
Conrming Nip Width ------------------------------------------------------------- 5-2
6
Trouble Shooting
Test Print ------------------------------------------------------------------------6-2
Test Print Function ----------------------------------------------------------------- 6-2
Trouble Shooting Items ------------------------------------------------------6-3
Image Faults ------------------------------------------------------------------------ 6-3
Log Collector -------------------------------------------------------------------6-8
OutLine ------------------------------------------------------------------------------- 6-8
Version Upgrade ------------------------------------------------------------ 6-10
Overview ----------------------------------------------------------------------------6-10
UST -----------------------------------------------------------------------------------6-10
Preparation -------------------------------------------------------------------------6-10
Downloading System Software ------------------------------------------------ 6-11
Upgrading via Internet -----------------------------------------------------------6-13
7
Error Codes
Overview ------------------------------------------------------------------------7-2
Error Codes
---------------------------------------------------------------------7-3
Jam Codes
----------------------------------------------------------------------7-4
8
Service Mode
Overview ------------------------------------------------------------------------8-2
Entering Service Mode. ---------------------------------------------------------- 8-2
Service Mode Menu --------------------------------------------------------------- 8-2
COPIER -------------------------------------------------------------------------8-4
DISPLAY ----------------------------------------------------------------------------- 8-4
I/O -------------------------------------------------------------------------------------- 8-5
ADJUST ------------------------------------------------------------------------------ 8-5
FUNCTION -------------------------------------------------------------------------- 8-6
OPTION ------------------------------------------------------------------------------ 8-8
COUNTER --------------------------------------------------------------------------- 8-9
FEEDER ----------------------------------------------------------------------- 8-11
ADJUST ----------------------------------------------------------------------------- 8-11
FUNCTION ------------------------------------------------------------------------- 8-11
FAX ----------------------------------------------------------------------------- 8-12
List of SSSW -----------------------------------------------------------------------8-12
List of MENU -----------------------------------------------------------------------8-14
List of NUM -------------------------------------------------------------------------8-15
List of NCU -------------------------------------------------------------------------8-16
TESTMODE ------------------------------------------------------------------ 8-20
SYSTEM ----------------------------------------------------------------------------8-20
SCAN --------------------------------------------------------------------------------8-20
FAX -----------------------------------------------------------------------------------8-21
PANEL -------------------------------------------------------------------------------8-22
NETWORK ------------------------------------------------------------------- 8-23
SSSW --------------------------------------------------------------------------------8-23
Appendix
Service Tools -------------------------------------------------------------------9-2
Solvent/Oil List
-----------------------------------------------------------------9-3
General Circuit Diagram (Duplex Model)
-------------------------------9-4
General Circuit Diagram (Simplex Model)
------------------------------9-5
General Timing Chart
--------------------------------------------------------9-6
List of User Mode
-------------------------------------------------------------9-7
Network Settings ------------------------------------------------------------------- 9-7
Preferences ------------------------------------------------------------------------- 9-8
Quiet Mode Time ------------------------------------------------------------------- 9-9
Common Settings ------------------------------------------------------------------ 9-9
Copy Settings ----------------------------------------------------------------------- 9-9
Fax Settings ------------------------------------------------------------------------- 9-9
Scan Settings ----------------------------------------------------------------------9-10
Printer Settings --------------------------------------------------------------------9-10
Adjustment/Maintenance --------------------------------------------------------9-10
System Management Settings -------------------------------------------------9-10
Backup Data ------------------------------------------------------------------ 9-12
CDRH Provisions
Laser Safety
Toner Safety
Notes on Handling
Lithium Battery
Notes on Assembly/
Disassembly
Safety Precautions
0
0
0-2
0-2
Safety Precautions > Laser Safety > Handling Laser Scanner Unit
Safety Precautions > Laser Safety > Handling Laser Scanner Unit
CDRH Provisions
Food and Drug CDRH (Center for Devices and Radiological Health) under FDA (Food and
Drug Administration) enforced provisions of the section for laser and laser products on August
2, 1976. These provisions are applicable to all laser products manufactured or assembled
after August 1, 1976 and allow only products certied their compliance with the provisions
to market in the US. Each product shall have afxed the applicable label as shown below to
follow the labeling requirements prescribed in CDRH provisions.
Note that the wording included in labels is different depending on laser product
classications.
F-0-1
Laser Safety
About Laser Beams
Laser radiation may be hazardous to human. The laser scanner unit mounted in this device is
sealed in the protective housing and the external cover to prevent laser beams from leaking
to the environment. As long as the device is operated under normal conditions, users are
safely guarded from laser leaks.
Handling Laser Scanner Unit
Before providing service works for the laser scanner unit and its peripherals, ensure to turn
off the power of the device.
Any cover with potential dangers of laser beam reection has afxed the caution label at the
position shown in the gure below.
This product is certicated as a Class 1 laser product under IEC60825-1:2007.
But this product is equipped with a class 3B laser.
When you remove interlock and work, you must warn the safety.
F-0-2
0
0
0-3
0-3
Safety Precautions > Notes on Assembly/Disassembly
Safety Precautions > Notes on Assembly/Disassembly
Toner Safety
About Toner
Toner is a nontoxic matter composed of plastic, iron and a trace of pigments.
Never throw toner in ames to avoid explosion.
Handling Adhered Toner
Use dry tissue paper to wipe off toner adhered to skin or clothes and wash in water.
Never use warm water for cleaning up toner to prevent toner particles from being able to
soak into bers permanently.
Toner particles are reactive with vinyl polymers. Avoid contacting these materials.
Notes on Handling Lithium Battery
Replacing with wrong battery types may cause explosion.
Follow instructions to dispose used batteries properly.
Notes on Assembly/Disassembly
Follow the items below to assemble/disassemble the device.
1. Disconnect the power plug to avoid any potential dangers during assembling/disassembling
works.
2. If not specially instructed, reverse the order of disassembly to reinstall.
3. Ensure to use the right screw type (length, diameter, etc.) at the right position when
assembling.
4. To keep electric conduction, binding screws with washers are used to attach the grounding
wire and the varistor. Ensure to use the right screw type when assembling.
5. Unless it is specially needed, do not operate the device with some parts removed.
6. Never remove the paint-locked screws when disassembling.
1
1
Product Overview
Product Overview
Product Lineups
Features
Product Specications
Name of Parts
1
1
1-2
1-2
Product Overview > Product Lineups > Options
Product Overview > Product Lineups > Options
Product Lineups
Main Unit
Model i-SENSYS MF229dw i-SENSYS MF226dn i-SENSYS
MF217w
i-SENSYS
MF216n
i-SENSYS
MF212w
i-SENSYS
MF211
Cong 4in1DADF+WN 4in1SADF+N 4in1SADF+WN 4in1SADF+N 3in1Pla+WN 3in1Pla
Design
ADF DADF SADF SADF SADF PLATEN PLATEN
Engine 2-Sided 2-Sided 1-Sided 1-Sided 1-Sided 1-Sided
LAN port Yes Yes Yes Yes Yes
Wireless LAN Yes Yes Yes
FAX Yes Yes Yes Yes
Options
Non
F-1-1
F-1-2
F-1-3
F-1-4
T-1-1
1
1
1-3
1-3
Product Overview > Manufacture Sketch Drawing
Product Overview > Manufacture Sketch Drawing
Manufacture Sketch Drawing
Duplex Model Sinplex Model
Duplex Model Sinplex Model
Duplex Model Sinplex Model
Duplex Model
Duplex Model
Sinplex Model
Sinplex Model
DADF Model
SADF Model
Copyboard Model
Edge Cooling Fan
Duplex Solenoid
Main Fan
Duplex Relay PCB
Intake hole of
the main fan
F-1-5
1
1
1-4
1-4
Product Overview > Product Specications > Main Unit Specications
Product Overview > Product Specications > Main Unit Specications
Features
Features
1. Small-size, high-speed monochrome printer
This equipment has a compact body that realizes high-speed print of 27 ppm (A4) / 26 ppm
(LTR).
2. Automatic duplex print
Automatic two-sided printing is available with standard equipped duplex unit.
3. Reduction in standby time and energy consumption
This equipment employs on-demand xing where the heater activates only during printing,
resulting in a reduction in standby time and energy consumption on this mode.
4. Realization of noise reduction and stable image quality
This equipment employs a belt drive method for transmitting the drive of the main motor.
This enables lower noise and more stable image quality compared to the conventional gear
drive method. (See NOTE)
5. Improved Usability
In this equipment maintenance (jam removal, replacing the cartridge) can be performed by
accessing one point of the delivery tray.
Note:
Changing the drive method from gear to belt reduces uneven pitch due to varied
rotation speed of the photosensitive drum, which realizes stable image quality.
Product Specications
Main Unit Specications
Copyboard Fixed
Device Installation Personal Desktop
Light source LED (RGB)
Image scanning CIS (color)
Photoreceptor OPC drum (φ24)
Light exposure
method
Laser beam exposure (semiconductor laser)
Charging method Roller charging
Developing method Toner projection developing method
Transfer method Direct transfer to the transfer member
Separation method Curvature separation
Paper feed method Pickup Tray : Semilunar-shaped Pickup Roller + Pad separation method
(pressure release mechanism is not available)
Multi-purpose Tray : Semilunar-shaped Pickup Roller + Pad separation
method (pressure release mechanism is not available)
Paper delivery
method
Face-down
Drum cleaning
method
Cleaning blade
Fixing method SURF xing method with the Ceramic Heater
Toner supply method All-in-one cartridge with drum
Toner level sensor Fax model: Yes (magnetic sensor)
Document types Sheets, Book, Height of document : 20 mm, Weight: up to 2 Kg
Maximum document
size
Fixation : to A4
ADF : to LGL
Image size
magnication
100% Direct, 400% Max, 200%, 129% STMT->LTR, 78% LGL->LTR, 64%
LTR->STMT, 50%, 25% Min
Zoom Zoom : 25 to 400 % (1 % increment)
Reading resolution Text/photo : 300 dpi x 300 dpi (default)
Text/photo : 600 dpi x 600 dpi
Text : 600 dpi x 600 dpi
Photo : 600 dpi x 600 dpi
Print resolution 1,200 dpi equivalent x 1,200 dpi equivalent
Warm-up Time 13.5 seconds or less
First print time 6.0 seconds or less
First copy time
Platen glass: 9 seconds or less
Feeder: 14 seconds or less
Print
Speed
Simplex
Print
Duplex Model: 28 ppm(LTR), 27 ppm(A4)
Simplex Model: 24 ppm(LTR), 23 ppm(A4)
Duplex
Print
Duplex Model: 16 cpm(LTR), 15 cpm(A4)
Simplex Model: Non Duplex Print
1
1
1-5
1-5
Product Overview > Product Specications > Main Unit Specications
Product Overview > Product Specications > Main Unit Specications
Copy
speed
Simplex
Print
Duplex Model: 28 ppm(LTR), 27 ppm(A4)
Simplex Model: 24 ppm(LTR), 23 ppm(A4)
Duplex
Print
Duplex Model: 16 cpm(LTR), 15 cpm(A4)
Simplex Model: Non Duplex Print
Available paper size
in Paper Cassette
Fixed size :
A4 *1 , B5, A5, Legal *1, Letter *1 , Statement, Executive *1, Ofcio *1,
B-ofcio *1, M-ofcio *1, Government - Letter, Government - Legal, Foolscap
*1, Australian-foolscap, Indian-Legal *1, Envelope COM10, Envelope
Monarch *2, Envelope C5, Envelope DL, Index Card *2
Custom paper size :
Envelope: COM10 / Monarch / C5 / DL
Width: 76.2 to 216.0 mm
Length: 148.0 to 356.0 mm
Available paper size
in multi-purpose tray
Fixed size :
A4 *1 , B5, A5, Legal *1, Letter *1 , Statement, Executive *1, Ofcio *1,
B-ofcio *1, M-ofcio *1, Government - Letter, Government - Legal, Foolscap
*1, Australian-foolscap, Indian-Legal *1, Envelope COM10, Envelope
Monarch *2, Envelope C5, Envelope DL, Index Card *2
Custom paper size :
Envelope: COM10 / Monarch / C5 / DL
Width: 76.2 to 216.0 mm
Length: 148.0 to 356.0 mm
Paper types for Paper
Cassette
Plain paper*3 (60 to 90 g/m²(16 to 24 lb Bond )), Heavy paper*4 (90 to 163
g/m²(24 to 60 lb Bond)), Recycled paper*3 (60 to 90 g/m²(16 to 24 lb Bond)),
Color paper*3 (60 to 90 g/m²(16 to 24 lb Bond)), Bond paper*5 (60 to 163 g/
m²(16 lb Bond to 60 lb Cover)), Transparency, Label, Envelope
Multi-Purpose Tray Plain paper*3 (60 to 90 g/m²(16 to 24 lb Bond )), Heavy paper*4 (90 to 163
g/m²(24 to 60 lb Bond)), Recycled paper*3 (60 to 90 g/m²(16 to 24 lb Bond)),
Color paper*3 (60 to 90 g/m²(16 to 24 lb Bond)), Bond paper*5 (60 to 163 g/
m²(16 lb Bond to 60 lb Cover)), Transparency, Label, Envelope
Stack capacity of
Paper Cassette
About 250 sheets (60 to 80 g/m2)
Stack capacity of
Multi-purpose Tray
1 sheet
Output tray stacking
capacity
About 100 sheets (60 to 80 g/m2)
Allowable
environmental
temperature
10 - 30 deg C(50 to 86°F)
Allowable humidity 20 - 80 %
Duplex method Yes
Interface
100BASE-TX
10BASE-T
Hi-Speed USB
IEEE 802.11b/g/n (Infrastructure mode)
Hard Disk Standard : none, Option : none
Power Supply 110 to 127 V, 50/60 Hz
220 to 240 V, 50/60 Hz
(Power requirements differ depending on the country in which you purchased
the product.)
Power Consumption <Maximum>
Duplex Model : 1,220 W
Simplex Model : 1,190 W
<Average consumption during standby mode>
Duplex Model : Approx. 5.8 W
Simplex Model : Approx. 5.4 W
<Average consumption during sleep mode>
Duplex Model :
Wired Connections : Approx. 1.7 W
Wireless Connections : Approx. 2.3 W
Simplex Model :
Wired Connections : Approx. 1.6 W
Wireless Connections : Approx. 2.0 W
<When the power switch is turned OFF>
0.5 W or less
Dimensions
(W x L x H)
DADF model:
390 mm x 378 mm x 360 mm(15" 3/8 x 14" 7/8 x 14" 1/4)
SADF model:
390 mm x 371 mm x 360 mm (15" 3/8 x 14" 5/8 x 14" 1/4)
PLATEN model:
390 mm x 371 mm x 312 mm(15 3/8" x 14 5/8" x 12 1/4")
Weight
(The value indicates
the mass of the main
unit including toner
cartridges.)
MF229dw: Approx. 13.7 kg(30.2 lb)
MF227dw: Approx. 12.8 kg(28.2 lb)
MF226dn: Approx. 12.8 kg(28.2 lb)
MF216n: Approx. 12.1 kg(26.7 lb)
MF212w: Approx. 10.8 kg(23.8 lb)
*1 : Only in Duplex Model, automatic 2-sided printing is available without replacing paper.
*2 : You can load Envelope Monarch and Index Card only in the manual feed slot
*3 : Only in Duplex Model, automatic 2-sided printing is available without replacing paper.
*4 : Only in Duplex Model, automatic 2-sided printing is available for heavy paper 1 (90 to 120
g/m²).
*5 : Only in Duplex Model, automatic 2-sided printing is available for bond paper 1 (60 to 90
g/m²) and bond paper 2 (90 to 120 g/m²).
T-1-2
1
1
1-6
1-6
Product Overview > Product Specications > SADF/DADF Specications
Product Overview > Product Specications > SADF/DADF Specications
Wireless LAN Specications
Standard IEEE 802.11g, IEEE 802.11b, IEEE 802.11n
Frequency Range 2,412 to 2,462 MHz
Data Transmission Rate
IEEE 802.11g
6/9/12/18/24/36/48/54 Mbps
IEEE 802.11b
1/2/5.5/11 Mbps
IEEE 802.11n
SGI Invalidated 20 MHz: 6.5/13/19.5/26/39/52/58.5/65 Mbps
SGI Validated 20 MHz: 7.2/14.4/21.7/28.9/43.3/57.8/72.2 Mbps
Communication Mode Infrastructure Mode
Security WEP 64/128 bit, WPA-PSK (TKIP/AES), WPA2-PSK (AES),
802.1x (LEAP, EAP-FAST, PEAP, EAP-TLS, EAP-TTLS)
Connection Method WPS (Wi-Fi Protected Setup), Manual setup
*
WPS (Wi-Fi Protected Setup), Connection can be established by manually setting values.
T-1-3
SADF/DADF Specications
Document pickup method Auto pickup method
Document setting direction face-up method
Document type Sheet document
Document size DADF Size: A4R/B5R/A5/B6 (landscape)/LGL/LTRR
2-sided: A4R/B5R/A5/LTRR/LGL/B6 (landscape only)
Feed direction : 127 mm to 356 mm
Width direction : 140 mm to 216 mm
SADF Size: A4R/B5R/A5/B6 (landscape)/LGL/LTRR
Feed direction : 105 mm to 356 mm
Width direction : 148 mm to 216 mm
Document
processing mode
SADF 1-sided document -> 1-sided copy, 1-sided document -> 2-sided copy
DADF 1-sided document -> 1-sided copy, 1-sided document -> 2-sided copy,
2-sided document -> 1-sided copy, 2-sided document -> 2-sided copy
Document weight Continuous feed 1-sided : 50 to 105 g/m
2
Continuous reading 2-sided : 60 to 105 g/m
2
Document stack
capacity *
DADF S size: 50 Sheets/L size : 10 Sheets
SADF S size: 35 Sheets/L size : 10 Sheets
Document setting position Center reference
Document reading method Stream reading
Mixed paper reading None
Document size sensor None
Document AE sensor None
Stamp function None
Document feed
speed
(at reading)
100 % DADF: 129.34 mm/s
SADF: 113.38 mm/s
Document
processing speed
(At A4, LTR)
Mono
1-sided constant speed, DADF
22 ipm (sheets/min)
1-sided constant speed, SADF
20 ipm (sheets/min)
2-sided constant speed, DADF
8 ipm (sheets/min)
Color
1-sided constant speed, DADF
15 ipm (sheets/min)
1-sided constant speed, SADF
15 ipm (sheets/min)
2-sided constant speed, DADF
5 ipm (sheets/min)
*:
Ssize: A4R, B5R, A5R, B6, LTRR, STMTR, 16KR
L size: LGL
T-1-4
1
1
1-7
1-7
Product Overview > Product Specications > FAX Specications(FAX model Only)
Product Overview > Product Specications > FAX Specications(FAX model Only)
FAX Specications(FAX model Only)
Line Used Public Switched Telephone Network (PSTN)*1
Communication Mode Super G3, G3
Compression Method MH, MR, MMR
Modem Speed Super G3: 33.6 Kbps, G3: 14.4 Kbps
Automatic Fallback
Transmission Speed Approx. 3 seconds per page*2
(ECM-MMR, transmitting from the memory at 33.6 Kbps)
Sending from Memory/
Receiving in Memory
Maximum approx. 256 pages*2 (Total pages of transmission/reception)
(Maximum number of fax jobs that can be sent from the memory: 10 jobs/
Maximum number of fax jobs that can be received into the memory: 90 jobs)
Fax Resolution
Normal: 200 x 100 dpi
Fine: 200 x 200 dpi
Photo: 200 x 200 dpi
Superne: 200 x 400 dpi
Dialing
One-touch keys (4 destinations)
Coded dialing (100 destinations)
Group dialing (103 groups)
Address Book dialing
Regular dialing (with numeric keys)
Automatic redialing
Manual redialing
Sequential broadcast (114 destinations)
Receiving
Automatic reception
Remote reception by telephone (Default ID: 25)
Reports
Send Results
Transmission management report
(By default, auto output every 40 destinations)
RX Results
Telephone Type External telephone/External telephone with the built-in answer function/Data
modem
*1 The Public Switched Telephone Network (PSTN) currently supports 28.8 Kbps modem
speed or lower. Note that speeds can vary depending on the telephone line conditions.
*2 Based on ITU-T (ITU Telecommunication Standardization Sector) Standard Chart No. 1,
MMR standard mode.
T-1-5
1
1
1-8
1-8
Product Overview > Name of Parts > External View > SADF Unit and Reader Unit
Product Overview > Name of Parts > External View > SADF Unit and Reader Unit
Name of Parts
External View
DADF Unit and Reader Unit
[10]
[13]
[12]
[11]
[1]
[2] [3] [4]
[5]
[6]
[7]
[9]
[8]
No. Name Remarks
[1] DADF Upper Cover -
[2] DADF Rear Cover -
[3] Side Guide Plate -
[4] Original Feed Tray -
[5] Original Feed Auxiliary Tray -
[6] Original Delivery Tray -
[7] DADF Front Cover -
[8] Document Reading Glass -
[9] Copyboard Guide Holder -
[10] White Guide Plate -
[11] White Plate -
[12] Copyboard Glass -
[13] Copyboard Upper Cover -
F-1-6
T-1-6
SADF Unit and Reader Unit
[10]
[13]
[12]
[11]
[1]
[2] [3] [4]
[5]
[6]
[7]
[8]
[9]
No. Name Remarks
[1] SADF Upper Cover -
[2] SADF Rear Cover -
[3] Side Guide Plate -
[4] Original Feed Tray -
[5] Original Feed Auxiliary Tray -
[6] Original Delivery Tray -
[7] SADF Front Cover -
[8] Document Reading Glass -
[9] Copyboard Guide Holder -
[10] White Guide Plate -
[11] White Plate -
[12] Copyboard Glass -
[13] Copyboard Upper Cover -
F-1-7
T-1-7
1
1
1-9
1-9
Product Overview > Name of Parts > External View > Printer Unit (Duplex)
Product Overview > Name of Parts > External View > Printer Unit (Duplex)
Copyboard Unit and Reader Unit
[1]
[4]
[2]
[3]
[5]
No. Name Remarks
[1] Copyboard Upper Cover -
[2] Copyboard Guide Holder -
[3] White Plate -
[4] Copyboard Glass -
[5] Copyboard Upper Cover -
F-1-8
T-1-8
Printer Unit (Duplex)
Front Side (Duplex)
[10]
[1]
[11]
[2]
[12]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
No. Name Remarks
[1] Control Panel Unit -
[2] Delivery Auxiliary Tray -
[3] Pickup Tray -
[4] Trailing Edge Paper Guides -
[5] Pickup Tray Side Guide Plate -
[6] Power Switch -
[7] Upper Cover -
[8] Delivery Tray -
[9] Front Cover Unit -
[10] Multi-Purpose Tray -
[11] Tray Cover -
[12] Multi-Purpose Tray Side Guide Plate -
F-1-9
T-1-9
1
1
1-10
1-10
Product Overview > Name of Parts > External View > Printer Unit (Sinplex)
Product Overview > Name of Parts > External View > Printer Unit (Sinplex)
Rear Side (Duplex)
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
No. Name Remarks
[13] Left Cover -
[14] Hinge Face Cover -
[15] Duplex Feed Guide Unit -
[16] Right Cover -
[17] USB Device Port -
[18] LAN Port Model with NET
[19] External Device Jack Model with FAX
[20] Telephon Line Jack Model with FAX
[21] Power Supply Cord Slot -
F-1-10
T-1-10
Printer Unit (Sinplex)
Front Side (Sinplex)
[10]
[1]
[11]
[2]
[12]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
No. Name Remarks
[1] Control Panel Unit -
[2] Delivery Auxiliary Tray -
[3] Pickup Tray -
[4] Trailing Edge Paper Guides -
[5] Pickup Tray Side Guide Plate -
[6] Power Switch -
[7] Upper Cover -
[8] Delivery Tray -
[9] Front Cover Unit -
[10] Multi-Purpose Tray -
[11] Tray Cover -
[12] Multi-Purpose Tray Side Guide Plate -
F-1-11
T-1-11
1 / 1

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document