Heath Zenith HZ-4265-OR Installation guide
- Category
- Work lights
- Type
- Installation guide
Motion Activated
Decorative Lighting
Decorative Light
Questions or problems? Before returning to your
retailer, refer to the troubleshooting guide in this
manual or call our technical service department
at 1-800-858-8501 (English speaking only), 8:00
am to 5:00 pm, CST, Monday – Friday.
FEATURES
-
tected.
hours.
is package includes:
REQUIREMENTS
Some electrical codes require installation by
a qualied electrician. Please check the codes
in your area.
Before installation, record the model num-
ber listed inside the xture. Attach receipt
in case of possible warranty issues.
Model Number:
Installation and
Operating Instructions
© 2013 HeathCo LLC 205071-02A
Model
4265
2
205071-02
WARNING: Turn power o at circuit
breaker or fuse. Place tape over circuit
breaker switch and verify power is o at
the xture.
Sensitivity Control
Wire Path Ground Screw
Mounting
Plate
INSTALLATION
Decorative Nut
Mounting Screw
Bracket
Mounting
Screw
Mounting
Plate
Junction
Box
Note:
the majority of junction box applications.
the mounting plate. Note:
on mounting plate (See
Recommended Ground-
ing Method
for additional information).
3. Flip the mounting plate over.
is on the upper right. Note:
xture to pass through.
-
tach the mounting plate to the junction box
Wire Path Wire Path
Fixture Screws
Ground Screw
As Shipped Flipped and
Rotated
For best performance, mount the xture about 6
feet (1.8 m) above the ground.
mounting plate.
5. Set sensitivity (SENS) control on back of
xture to mid-position.
MAX
MIN
SENS
3
205071-02
Black to black White to white
Recommended Grounding Method
WIRING
Note:
the National Electrical Code through conduit
or another acceptable means. Contact a quali-
ed electrician if there is any question as to the
suitability of the system.
CAUTION: DO NOT connect the RED wire
unless you want to control other lights from
the motion sensor (see Optional Wiring).
-
grounding method, consult your local building
code.
One Motion Light
Two Motion Lights
Black
White
Green
or Bare
Light
Fixture
Black
White
Green
or Bare
Light
Fixture
Light
Fixture
4
205071-02
Black
White
Green
or Bare
Light
Fixture
Light
Fixture
(Standard) Master Slave
Black
White
Green
or Bare
Light
Fixture
Light
Fixture
Red
Red
Wiring Diagram 1 Wiring Diagram 2
Wiring Diagram 3
Master
Black
White
Red
Green
or Bare
Master
Light
Fixture
Light
Fixture
OPTIONAL WIRING
Wiring Diagram 1 – When wiring to control a standard light xture:
redblack
Wiring Diagram 2 – When wiring to control another motion sensing light xture (Master /
Slave): Strip the redred
xture to the red and black
Wiring Diagram 3 – When wiring so either motion light turns on the both motion lights
(Master / Master): Strip the redred
to the redNote:
5
205071-02
Junction Box
FINAL ASSEMBLY
Slide the xture assembly onto the mounting
1 of Installation section securely against xture
base.
Mounting Screw
Decorative Nut
maximum). See
Bulb Replacement
section for
bulb installation.
TESTING AND ADJUSTMENTS
1. Turn on the circuit breaker and light
switch.
Note: Sensor has a 1
1
1
minutes.
TEST 1 5 10 MIN
OFF 3 6 DUSK TO
HOUR DAWN
6
205071-02
3.
4.
or decrease the range as needed. Too much
sensitivity may cause false triggering due to
heat sources in the coverage area (see
Adjust-
ment of Coverage Area or Troubleshooting
section).
light to stay on after motion is detected (1, 5,
or 10 minutes).
6. Set the
sealant.
Note:
1
minutes
for the circuitry to calibrate.
e sensor is less sensitive to motion directly
coverage area.
OPERATION
... back on.
1 Second
OFF then...
night because daylight returns
one second then back on to
1, 5, or 10 position.
MANUAL MODE
Mode: On-Time Works: Day Night
Test
5 Seconds x x
Auto
1, 5, or 10
Minutes
x
Accent
3, 6 Hour,
x
Manual
x
30 ft.
(9.1 m)
6 ft.
(1.8 m)
150°
Maximum Range Maximum
Coverage Angle
(Top View)
Least Sensitive Most Sensitive
Sensor
Motion Motion
7
205071-02
ADJUSTMENT OF COVERAGE AREA
by the movement of heat across the coverage
that also produce heat and can cause the sensor
to trigger:
triggering the sensor, reduce the sensitivity.
MANUAL MODE
AUTO
TEST
ON-TIME Switch at 1, 5, or 10
minutes
MODE SWITCHING SUMMARY
Flip light switch o for
one second then back
on*
BULB REPLACEMENT
1. Remove decorative nut on top of xture cap.
3. Replace bulb.
4. Replace cap onto xture making sure ring is
on decorative hook.
5.
Decorative Nut
Decorative Hook
Decorative Ring
Fixture Cap
Remove Fixture Cap
mode.
DualBrite® Dimmer Control
disables this feature. e motion sensing features
returns to dim mode.
8
205071-02
TROUBLESHOOTING GUIDE
SYMPTOM POSSIBLE CAUSE SOLUTION
come on.
5. Sensor not detecting movement.
3. Replace fuse or turn circuit breaker on.
4. Recheck after dark.
daylight.
1. e xture is operating normally under these
conditions.
no apparent reason.
1. Reduce sensitivity.
continuously.
1. e sensor may be picking up a heat source like an air
surface.
4. Sensitivity is set too high.
1. Reduce sensitivity.
3. Slide
4. Reduce sensitivity.
the sensor.
1. Flashing is normal under these conditions.
SPECIFICATIONS
Range .................................................
.....................................Up to 150°
...................................
Bulb Type ...........................................
Sensor Capacity ..................................
...........................
...............................
.......................................... 1, 5, 10 minutes
Timer ...........................
Test Timer .......................................... 5 Seconds
Manual Mode Timer ..........................
9
205071-02
TWO YEAR LIMITED WARRANTY
to state or province to province.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and
-
Please keep your dated sales receipt, it is required for all warranty requests.
TECHNICAL SERVICE
Please call 1-800-858-8501 (English speaking only) for assistance before
returning product to store.
www.
hzsupport.com1-800-858-8501 (English speaking
No Service Parts Available for this Product
Please keep your dated sales receipt, it is required for all warranty requests.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
28
205071-02
Staple Purchase Receipt Here
Engrape aquí el recibo de compra
Agrafez le reçu d’achat ici
PLEASE KEEP YOUR DATED SALES RECEIPT,
IT IS REQUIRED FOR ALL WARRANTY REQUESTS.
POR FAVOR GUARDE SU RECIBO DE VENTA FECHADO; SE LO
REQUIERE PARA CUALQUIER SOLICITUD DE GARANTÍA.
VEUILLEZ CONSERVER LE REÇU PORTANT LA DATE D'ACHAT;
VOUS EN AUREZ BESOIN POUR TOUTES VOS DEMANDES LIÉES À
LA GARANTIE.
Purchase Information
Información de la compra
Renseignements d’achat
Model #: ________________________ Date of Purchase: _______________________
Nº de modelo / N° de modèle Fecha de compra / Date d’achat
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Heath Zenith HZ-4265-OR Installation guide
- Category
- Work lights
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Heath Zenith HZ-4114-HB Installation guide
-
Heath Zenith HZ-4151-BR1 User manual
-
Hampton Bay SL-4133-OR User manual
-
HeathZenith HZ-4192-BK User manual
-
-
-
-
-
-
Other documents
-
Secure Home SH-4192-BK-A User manual
-
ProPOW B075PXDKS2 User manual
-
Design House 514992 Installation guide
-
Lutec 7622111 User guide
-
Hampton Bay HBI-4192-WH Installation guide
-
Defiant DFI-5936-WH FAQ
-
HeathZenith SL-4110 Motion-activated Coach Light User manual
-
-
Health Zenith DualBrite 4700 Installation And Operating Instructions Manual
-
Hampton Bay HBI-4197-WH Operating instructions
