2. Home
  3. Home security & automation
  4. Motion detectors
  5. Hampton Bay
  6. HBI-4192-WH

Hampton Bay HBI-4192-WH Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Hampton Bay HBI-4192-WH Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Motion Sensing
Diecast Lantern
HB-4190 Series
Features
• Lightcomesonwhenmotionisdetected.
• Automaticallyturnslightoff.
• DuskAccentlighting.
• Photocellkeepsthelightoffduringdaylight
hours.
Requirements
• Thelightcontrolrequires120voltsAC.
• IfyouwanttouseManualMode,thecontrol
mustbewiredthroughaswitch.
• Some codes require installation by a
qualified electrician.
©2009 595-5770-06
OPERATION
*resetstoAutoModeatdawn.
SettheON-TIMEswitch
on the bottom of the
coverplatetoTEST.
TEST 1 510 MIN
SetON-TIMEswitchto
1,5,or10minutes.
1Second
OFFthen...
Manualmodeonlyworksat
nightbecausedaylightre-
turnsthesensortoAUTO.
Flipthelightswitchofffor
onesecondthenbackonto
togglebetweenAUTOand
MANUALMODE.
Manual mode works only
withtheON-TIMEswitchin
the1,5,or10position.
...backon.
Thispackageincludes:
• Lantern
• Easy to use universal mounting bracket
(X-Bar)
• Mountinghardware
• Wirenuts
Note:Whenrstturnedonwaitabout1
1
/
2
minutesforthecircuitrytocalibrate.
TEST
AUTO
MANUAL MODE
TEST 1 5 10 MIN
Mode: On-Time Works: Day Night
Test 5Seconds x x
Auto 1,5,or10Min x
Manual ToDawn* x
Accent 3,6Hr,toDawn x
2
595-5770-06
INSTALLATION
Forbestperformance,mountthextureabout
6feet(1.8m)abovetheground.
1.Remove
twonuts.
2.Remove
X-Bar.
Junction
Box
5.AttachX-Barto
junctionbox
Duetothesizeandweightofthexture,you
mayndithelpfultohaveanassistantholdthe
xtureinplacewhileconnectingthewires.
MAX
MIN
3.Tightenscrews
ngertight.
SENSITIVITY
4.Setsensitivityon
xturebacktothe
mid-position.
ON-TIME Switch at 1,
5, or 10 minutes
Mode Switching Summary
Flip light
switch off for
one second
then back on*
MANUAL MODE
AUTO
TEST
* Ifyougetconfusedwhileswitchingmodes,
turnthepoweroffforoneminute,thenback
on.Afterthecalibrationtimethecontrolwill
beintheAUTOmode.
Du a l Br i t e
®
Dimmer Control
Lightcomesonhalfbrightforselectedtimeaf-
terdusk(Off,3hr.,6hr.,untildawn).Selecting
OFFdisablesthisfeature.Themotionsensing
featureswillcontinuetoworkasdescribed
inthismanual.Ifmotionissensed,thelight
turnsonfullbrightfortheON-TIME(1,5,or
10minutes)thenreturnstodimmode.
WARNING: Turn power off at circuit
breaker or fuse.
3
595-5770-06
Recommended Grounding Method
Useagreenground“pigtail”(notprovided)and
twistoneendtogetherwiththebarexturewire
andtheboxgroundwire.Securewithawire
connector.Securetheotherendofthe“pigtail”
withtheGNDscrewontheX-bar.
Blacktoblack
Whitetowhite
WIRING
One Motion Light
❒ Twist the junction box wires and the
xturewirestogetherasshownbelow.
Securewithwireconnectors.Ifyouhave
ametaljunctionbox,youmaynotneed
thegreen“pigtail”.Ifyouareunsureabout
thegroundingmethod,consultyourlocal
buildingcode.
Two Motion Lights
Black
White
Green
orBare
Light
Fixture
Black
White
Green
orBare
Light
Fixture
Light
Fixture
CAUTION: DO NOT connect the RED
wire unless you want to control other
lights from the motion sensor.
Note:Allwiringshouldberuninaccordance
with the National Electrical Code through
conduit or another acceptable means.
Contact a qualified electrician if there is
any question as to the suitability of the
system.
Connectthexturewirestothewiresinthe
junction box. Twist the wires together and
securewithwireconnectors.
4
595-5770-06
OPTIONAL WIRING
Thisxtureisprovidedwithasensorratedfor360Watts.Sincethextureisonlyrated100
Watts,260Wattsofadditionalloadmaybecontrolledbythissensor.
Whendeterminingwhataxtureisratedfor,donotsimplylookattheratingonthelight
bulbinthexture.Lookatthemarkingwhichspeciesthemaximumbulbwattageforwhich
thextureissuitable.
Onceyouhaveselectedthexturestobeconnectedanddeterminedtheirmaximumrat-
ings,addtheseratingsup.Forinstance,ifyouhave3xturesrated100Watts,150Watts,
and75Wattsrespectively,youhaveatotalloadof325Watts.
Wiring Diagram 1 – When wiring to control a standard light fixture:Stripthemotion
sensor’sredwireandconnecttothestandardlight’sblackwire.Connectallwhitewires
together.Totalxtureratingsmustnotexceed360Watts(3.0A).
Wiring Diagram 2 – When wiring to control another motion sensing light fixture (Mas-
ter / Slave):Striptheredwireinbothlightxtures.Connecttheredwireofthecontrolling
(master)xturetotheredandblackwiresofthecontrolled(slave)xture.Connectallwhite
wirestogether.Totalxtureratingsmustnotexceed360Watts(3.0A).
Wiring Diagram 3 – When wiring so either motion light turns on both motion lights
(Master / Master):Striptheredwireinbothlightxtures.Connecttheredwireofonexture
totheredwireofthesecondxture.Note:Inmostinstallations,anadditionalwire(same
gaugeasexistinghousewire)willhavetobeinstalledinthehousetoconnectthetwox-
turesasmaster/master.Connectallwhitewirestogetherandallblackwirestogether.Total
xtureratingsmustnotexceed360Watts(3.0A).
Black
White
Green
orBare
Light
Fixture
Light
Fixture
(Standard)
Master Slave
Black
White
Green
orBare
Light
Fixture
Light
Fixture
Red
Red
Wiring Diagram 1 Wiring Diagram 2
Wiring Diagram 3
Master Master
Black
White
Red
Green
orBare
Light
Fixture
Light
Fixture
5
595-5770-06
COMPLETE THE INSTALLATION
❒ Stuffthewiresintothejunctionbox.Make
surenoneofthewiresgetpinched.
Slidethextureontothe
mountingscrewsand
tightennuts.
❒ Installone 100 Wattmaximumlightbulb,or
three 60 Wattbulbsincandelabrastyle.
❒ Install the fixture top. Secure with
decorativescrews.
❒ Aftercompletingthetestsonpage6,caulk
fixture mounting surfacewithsilicone
weathersealant.
Junction
Box
Model 4193 Glass Installation
❒ Model 4193 only: install the six pieces
ofglassbyslidingthemdownasshown.
The glass panels should rest upon the
cornerguidesoneachside,andagainst
therubberbumpersatthebottom.
Note:Aswithanyglass,handlewithcare.
Corner
Guides
RubberBumpers
6
595-5770-06
TESTING
❒ Turn on the circuit breaker and light
switch.
NOTE: Sensorhasa1
1
/
2
minutewarmuppe-
riodbeforeitwilldetectmotion.When
rstturnedon,wait1
1
/
2
minutes.
❒ Switchtheon-timetoTESTpositionand
Du a l Br i t e
®
switchtotheOFFposition.
Thedetectorislesssensitivetomotiondi-
rectlytowardsitandmoresensitivetoacross
motion.
Sensor
Motion
Least Sensitive Most Sensitive
❒ Walkthroughthe coverage areanoting
whereyouarewhenthelightsturnon.
❒ If you need to change the sensitivity,
temporarilyremovethextureandmake
theadjustment.Toomuchsensitivitymay
increasefalsetriggering.
❒ SettheamountofTIMEyouwantthelight
tostayonaftermotionisdetected.(1,5,
or10minutes).
❒ Settheamountoftimeafterduskyouwant
thelightsonaccentlevel.
TEST1510MIN
ON-TIME
OFF 3 6 DUSK TO
HOUR DAWN
Avoid aiming the control at:
•Objectsthatchangetemperaturerapidly,
suchasheating vents and air condition-
ers.Theseheatsourcescouldcausefalse
triggering.
•Areaswherepets or trafficmaytrigger
thecontrol.
•Nearby large, light-colored objects
reecting light may trigger the shut-off
feature. Do not point other lights at the
sensor.
30ft.
(9.1m)
Maximum Range Maximum
Coverage Angle
6ft.
(1.8m)
180°
Motion
7
595-5770-06
SPECIFICATIONS
Range........... Up to 30 ft. (9.1 m)
[varieswithsurrounding
temperature]
SensingAngle..... Upto180°
ElectricalLoad..... See rating on xture
formaximumwattage
SensorCapacity ... Upto360Watts(3.0A.)
Maximum Tungsten
Incandescent
PowerRequirements 120VAC,60Hz
OperatingModes... TEST, AUTO, and
MANUALMODE
TimeDelay ....... 1,5,10minutes
Du a l Br i t e
®
Timer... Off,3,6hours,dusk-to
dawn
TheHamptonBayLightingCompanyreserves
the right to discontinue products and to
change specications at any time without
incurringanyobligationtoincorporatenew
featuresinproductspreviouslysold.
8
595-5770-06
SYMPTOM
Light stays on
continuously.
Light flashes
on and off.
POSSIBLE CAUSE
1. Thesensorispointedtoward
a heat source like an air
vent, dryer vent, or brightly-
paintedheat-reectivesurface.
(Reduce sensitivity.)
2. LightcontrolisinManualMode.
(Switch to Auto.)
3. Light control isin Du a l Br i t e
®
mode.
4. Sensitivityissettoohigh.(Re-
duce sensitivity.)
1. Light control is in the Test
mode and warming up.
(Flashing is normal under
these conditions).
2. Heatbeingreectedfromother
objects may be affecting the
sensor.(Reduce sensitivity.)
POSSIBLE CAUSE
1. Lightswitchisturnedoff.
2. Bulbislooseorburnedout.
3. Fuseisblownorcircuitbreaker
isturnedoff.
4. Daylight turn-off is in effect
(recheck after dark).
5. Incorrectcircuitwiring,ifthisis
anewinstallation.
1. Lightcontrolmaybeinstalled
inarelativelydarklocation.
2. Light control is in Test. (Set
control switch to an ON-TIME
position.)
1. Light control may be sensing
smallanimalsorautomobiletrafc
(Reduce sensitivity).
2. Sensitivityissettoohigh.(Re-
duce sensitivity.)
SYMPTOM
Light will not
come on.
Light comes on
in daylight.
Light comes on
for no apparent
reason.
TROUBLESHOOTING GUIDE
Ifyouexperienceaproblem,followthisguide.
No Service Parts Available for this Product
/