ESAB Power Line Filter/Conditioner Troubleshooting instruction

Brand: ESAB

Model: Power Line Filter/Conditioner

Type: Troubleshooting instruction

Be sure this information reaches the operator.

You can get extra copies through your supplier.

INSTRUCTIONS for

F-15-297

March, 1996

Installing

POWER LINE FILTER/CONDITIONER

P/N 35910 - 600 vac, 3-phase, 16 amp/phase

P/N 35911 - 600 vac, 3-phase, 25 amp/phase

F-15-297

To install Filter/Conditioner, refer to installation instruc-

tions and Figures 1 and 2 on the back of this form.

Power Line Filter/Conditioner is recommended for use

with inverter type power sources where 460 or 575 volt

input power surges and spikes are common. It will also

reduce input current draw by at least 25% as well as

improve power factor and efficency.

The 10" X 8" X 7" Filter/Conditioner is wall mountable.

It should be located no more than 2 feet from the power

source. The Filter/Conditioner is equipped with a 12-

foot long, 4-conductor, #10AWG input power cable for

connecting to your 460 or 575 vac power.

P/N 35910 Filter/Conditioner can be used with any 460

or 575 vac, 3-phase power source having an input cur-

rent draw up to 16 amps/phase such as PCM-750i (460

575 vac) and PCM-1000i (575 vac). P/N 35911 is de-

signed for power sources with higher input current draw

up to 25 amps/phase such as PCM-1000i (460 vac),

SVI 300i, and SVI 450i.

INPUT

POWER

OUTPUT

INVERTER

POWER LINE FILTER

600VAC, 3 PHASE 16 AMP/PHASE

P/N 35910

Before installing this accessory, make sure all in-

put power is disconnected and/or lock out proce-

dures are in place.

3. Connect the white, red and black wires to terminals

A2, B2 and C2 respectively in the box and connect

green ground wire to the ground terminal. Make

sure all connections are tight. Tighten the strain relief

to secure the power cable.

To install Filter/Conditioner, proceed as follows:

1. Cut off input power cable to the power source to 2

feet maximum. Strip insulation off the end of each

wire to expose 1/2" to 5/8" of bare wire.

NOTE: If connecting for single phase, use only the black

and white wires.

4. Connect the 12-ft. long input cable of the filter/condi-

tioner box to your 460 or 575 vac power supply. Your

power source is now ready for return to welding or

cutting operation.

2. Open the filter/conditioner box cover. Insert the power

source's input power cable through the strain relief

at the output end of the box.

PCM-750i or PCM-1000i

Any Length*

35910 or 35911

2 ft.

Max

To Input

Power Line

* 35910 & 35911 are equipped

W/12 ft. 4-cond cable.

Fig. 1 - Interconnection Diagram

SCHEMATIC

Fig. 2 - Schematic Diagram/Replacement Parts - Filter/Conditioner Assembly, P/N 35910 and 35911.

R2 R1

C2 C1

CABLE, 4-COND/#10AWG

- 36275

LABLE, DANGER

- 954008

BOX, 16A - 32222

25A - 32223

(2) STRAIN RELIEF

3/4 NPT

- 13734727

(3) RESISTOR

330K 1W 10%

(R1,2,3) - 17130433

BRACKET, MOUNTING CAPACITOR

- 36282

DECAL, GROUND

- 2091558

(3) CAPACITOR

2.2uf 300VAC

(C1,2,3) - 952163

F-15-297 3/96 1M Printed in U.S.A.

REACTOR, 16A - 52164

25A - 52165

ESAB Power Line Filter/Conditioner Troubleshooting instruction

ESAB Power Line Filter/Conditioner Troubleshooting instruction

ESAB Power Line Filter/Conditioner Troubleshooting instruction

Related papers

Other documents