ESAB Digipulse 450i Power Source for 575-Volt Service User manual

  • Hello! I am an AI chatbot trained to assist you with the ESAB Digipulse 450i Power Source for 575-Volt Service User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
SUPPLEMENT to Form 15-014
DIGIPULSE 450i POWER SOURCE for 575-VOLT SERVICE
Part No. 31238
I. General
This supplement covers the Digipulse 450i Power Source spe-
cifically designed for 575 Volt — 60 Hertz service. It is identi-
cal to the standard Digipulse 450i, P/N 31120 unit covered in
Form 15-014 except for the following:
IMPORTANT
As shipped from the factory, all 575-volt units are hooked-
up to operate “only” from a 575 volt input. This unit “does
not” contain a Voltage Changeover Input Terminal Board
assembly.
A. Replacement Parts:
Main Transformer Assy. (MTR) - P/N 31685 replaces P/N
31133.
Control Transformer Assy. (MTR) - P/N 31686 replaces
P/N 31134.
Power P.C. Board Assy. (PB1 and PB2) — P/N 31423 re-
places P/N 674991.
Capacitors (C5 and C6) — P/N 672348 replaces 950516.
II. Form 15-014 is applicable to this unit except as
follows:
A. See Revised Specification Table following.
B. See Revised Table for Recommended Input Conduc-
tors and Line Fuses.
Note that the customer can either use the factory supplied
input power cable (No. 6 AWG, 4/c, type SO, 90° C, 12-ft. lg.),
or provide his own leads per the Input Table.
Rated Input Input & Gnd. Time-Delay
Conductor Fuse Size
Volts Amps CU/AWG Amps
575 32 8 50
* Sized per National Electric Code for 90° C rated copper conductors @ 30° C
ambient. Not more than three conductors in raceway or cable. Local codes
should be followed if they specify sizes other than those listed above.
SPECIFICATIONS
Rated Output @:
60% Duty ........................................... 450 amps @ 38 vdc
100% Duty ......................................... 350 amps @ 34 vdc
Open Circuit Voltage ................................................. 72 vdc
Input Voltage ....................................... 575 vac, 3 ph, 60 Hz
Input Current @ Rated Load ................ 32 amps @ 575 vac
Dimensions:
15.25" (387 mm) W x 23.0" (584 mm) D x 15.5" (394 mm) H
Weight, Net .................................................. 161 lbs (73 kg)
C. Changes To Troubleshooting Section VI, as follows:
All resistance and low voltage check readings described in
15-014 are applicable to this unit, except those designated
with the symbol H.V. . This symbol indicates “high” voltage
checks which are not applicable, and cannot be safely made
in this unit because it does not contain an input terminal board
— reference the Capacitor Warning in the booklet (15-014).
D. Revised Wiring Diagram Contained Herein.
E. Revised Schematic Diagram Contained Herein.
Be sure this information reaches the operator.
You can get extra copies through your supplier.
F-15-015
F-15-015
June, 1995
2
Schematic Diagram - Digipulse 450/575 V.
D-31683
3
Wiring Diagram - Digipulse 450/575 V. (sh. 1 of 2)
D-31684
Wiring Diagram - Digipulse 450/575 V. (sh. 2 of 2)
F-15-015 6/95 Printed in U.S.A.
D-31684
1/4