2. JADEMAR
  3. JSLCT-SOL Series

JADEMAR JSLCT-SOL Series User manual

  • Hello! I am an AI chatbot trained to assist you with the JADEMAR JSLCT-SOL Series User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
• Sculpture/Memorial
• Billboard/sign
• Pathway
• Sign boards
• Wall washer
• Garden feature
• Commercial product
Model-31
Model-60
Model-90
Model-120
Model-3 Model-61 0 Model-90 Model-120
Solar Panel Po r we 5.5V 4.5W 5.5V 9W 5.5V 13W 5.5V 17W
Bat eryt 3.7V 8800mAh 3.7V 17600mAh 3.7V 26400mAh 3.7V 35200mAh
LED Po r we 5W 10W 15W 20W
Chargin Time g 8-9 Hou s(10r 00W/㎡)
LED Color Warm white/Natural white/Cool white
LED Life Time ＞50000 Hours
Product Size 300*95*95mm 600*95*95mm 900*95*95mm 1200*95*95mm
Beam Angle 120 Degree
Material Aluminum Alloy+PC
Con roller t Sunshine Control Automatic
Work Mode 4 hrs full bright + 25% brightness dim till dawn
INSTALLATION REQUIREMENTS
WARNING: Risk of electric shock and serious injury. SHUT OFF BREAKER AT PANEL BEFORE INSTALLING.
J T-SOL SERIES SLC OFF-GRID SOLAR SIGN LIGHT
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised /2001 22
Page of 1 3
INSTALLATION INSTRUCTIONS
Please read these instrucons before installaon to ensure opmum results and longevity of your lights. The solar panel should be charged in full sunlight for 6 to 8
hours before first use to obtain opmum results.
1.0 PACKAGE CONTENTS
1. Solar Panel and Baery box with LED array (1 pcs)
2. Wall brackets (2 pcs)
3. Instrucon sheet (1 pcs)
2.0 APPLICATIONS
3.0 FEATURES
• Easy installaon- no electrical wiring required with integrated design.
• Turns on automacally at night and off during the day.
• The lights include an On/Off switch and built in baery.
• Baery can support 2-3 nights with cloudy days.
• When the baery is full charged in sunlight, the lights will operate up to 3 nights.
• Intelligent power saving mode increases lighng x 1.5 mes.
• IP65 water and dust resistance.
4.0 HOW THE SOLAR PANEL WORKS
During the day, the solar panel converts sunlight into electricity to charge the baery. At night, the lights turn ON automacally using the electricity stored in the
baery. The performance of the solar lights is dependent on the locaon of the solar panel and/ or weather condions. Install the solar panel in a sunny posion
ensuring it receives 6-8 hours sunlight each day. Reduced sunlight will reduce connuous working hours at night.
Please note: during connuous wet & overcast days, lighng me may be reduced as the baery will not be fully charged. The lights may stop working during
longer rainy periods of more than 5 days & will return to normal funcon when the sun returns. Aer an extended period of poor weather restore the baery
power by turning the unit off and, fully charge the baery for 8 hours in full sunlight.
5.0 PRODUCT PARAMETERS
JSLCT-SOL SERIES OFF-GRID SOLAR SIGN LIGHT
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468
6.0 INSTALLATION STEPS - INSTALLATION WITH BRACKETS
Revised 01/2022
Page of 2 3
1. Using the brackets as a template, mark out and drill the mounng holes for the bracket. Insert the wall anchors provided.
2. Fix the two brackets onto the sides of the light. Use the exisng screws in the bracket fixing locaon by removing the screws and reinstang them with the
brackets in place.
3. Install the brackets into the pre-drilled wall holes making sure to use the washers. Tighten the screws and check the unit is square and straight.
4. Turn on the main power buon to acvate the LED display under the solar panel.
(Model-3 0 only) 1 and Model-6
7.0 INSTALLATION STEPS - DIRECT FIXED TO THE WALL
1. Mark out and drill the mounng holes to correspond with the mounng locaons on the light. Insert the wall anchors provided.
2. Insert the screws into the wall anchors and ghten.
3. Directly hang the unit onto the screws, ensuring the unit is square and straight.
4. Turn on the main power buon to acvate the LED display under the solar panel.
Notes:
1. All screws and bolts must be ghtened firmly.
2. Only press the main power buon once. The light will operate automacally at night.
3. Please charge the product for 6-8h before use.
8.0 NOTES
1. The solar light will automacally turn off when it detects low voltage from the baery. This may happen aer 3-4 cloudy days. For best charging performance,
please place light in direct sunlight.
2. To test the light during daylight hours, fully cover the solar panel and press the main power buon.
Note: This product uses a series of 3.7V, 2200mAh rechargeable lithium baery
BATTERY WARNINGS – Do not dispose of baeries in regular household waste. Do not get the baeries wet, hot or in contact with flames.
Dispose of baeries at your local baery recycle center. Do not expose to flames or other corrosive material. Follow aviaon safety
guidelines were applicable.
INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised /2001 22
Page of 3 3
JSLCT-SOL SERIES OFF-GRID SOLAR SIGN LIGHT
9.0 BATTERY REPLACEMENT
Step 2: This step is very important,
be sure to disassemble (unscrew)
the mounng
bracket
and
end
cap
on the button side of the light
fing.
Step 3: After open the end cap at the
buon
side,
removing
the
quick
connecon cable clamps smoothly to
avoid damaging the wire.Disconnect the
wires marked
(S h/LED/display)olar/switc
and gently
slide
out
the
baery
pack.
Step4:
a.Ensure replacement
baery
compartment
is
inserted
in
the correct direcon:
1. Cables
marked
(display/LED)
insert
towards
LED
display
2.Cables mark de with (solar/switch) extend towards
ON/OFF buon
side.
b.R coe nnect
the cables marke ar/Switc )d(display/LED/Sol h
respecvely, then slide over connector isolaon covers
(clear silicon cove sr ). Slide the baery back into the SSL
fixture.
Step 5: a.Replace buon end capto light fing then ghten
screws firmly. Note: Do not over ghten as aluminum threads will
strip.
b.
To
reset
and
test
push
in
the
ON/OFFbuon
and
ensure all the
solar panel is covered to prevent UV light reaching the surface.
The
light
will
turn
ON
automacally.
Note:
Leaving
the
ON/OFF
buon engaged and covering the solar
panel will cause the SSL fixture to turn ON automacally. When
the solar panel is unco erv ed and expose it to light the
LED’s will
immediately
turn
OFF
and
baery
will
begin
to charge.
Performing
this
test
will
det rminee
if
the
baery
replacement
was
succe fss ul.
If
the
above
does
not
occur
then
installaon steps
must
be
repeated,
double
checking
connectors
are
in correct
order.
Step6:
Line
up
all
sc wre s
on
the
back
of
the
light
fing,
then ghten.
This is best done before re-fing the end cap, as
the baery
compartment can be maneuvered to help line up back screws.
Step
7:
Check
all
seals
and
fing
are
in
place,
then
re-install buon
end
cap
and
mo ngun
brackets, ghten screws firmly. (do not
cross thread screws. All screws should be done up by fingers
before using a screwdriver to finish.
Step1: Loosen rear facing sc wre s
on main frame, ensure the baery
box is loose (free) to move.
Switch
Display Solar
Led
INSTALLATION INSTRUCTIONS
/