Samsung SOC-B120P User manual

E

R

User's guide

êÛÍÓ‚Ó‰ÒÚ‚Ó ÔÓÎ¸ÁÓ‚‡ÚÂÎﬂ

Observation Camera

SOC-C120P

SOC-B120P

AB68-00471A

3

E

2

E

Important Safety Instructions

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE REAR COVER. NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

This symbol indicates high voltage is

present inside. It is dangerous to

make any kind of contact with any

inside part of this product.

This symbol alerts you that important

literature concerning operation and

maintenance has been included with

this product.

5. If any unusual smells or smoke come from the unit,

stop using the product. In such case, immediately

disconnect the power source and contact the service

center. (Continued use in such a condition may cause

fire or electric shock.)

6. If this product fails to operate normally, contact the

store of purchase or your nearest service center.

Never disassemble or modify this product in any way.

(The manufacturer is not liable for any damage

resulting from unauthorized disassembly or repairs.)

7. When cleaning, do not spray water directly onto parts

of the product. (Doing so may cause fire or electric

shock.) Wipe the surface with a dry cloth. Never use

detergents or chemical cleaners on the product, as

this may result in discoloration of surface or cause

damage to the finish.

1. Do not drop objects on the product or apply strong

shock to it. Keep away from a location subject to

excessive vibration or magnetic interference.

2.. Do not install in a location subject to high temperature

(over 50°C/122°F), low temperature (below -10°C

/14°F), or high humidity. (Doing so may cause fire or

electric shock).

3. Avoid a location which is exposed to direct sunlight,

or near heat sources such as heaters or radiators.

(Neglecting to do so may result in a risk of fire).

4. If you want to relocate the already installed product, be

sure to turn off the power and then move or reinstall it.

5. Install in a well - ventilated location.

6. Remove the power plug from the outlet when there is

a lightning storm. (Neglecting to do so may cause fire

or damage to the product.)

1. Make sure that the cable is plugged in securely

before using. (A loose connection may result in fire.)

2. When installing the camera on a wall or ceiling,

mount it safely and securely. (A falling camera may

cause personal injury.)

3. Do not place conductive objects (e.g., screwdrivers,

coins, and metal things) or containers filled with

water on top of the camera. (Serious injury may

result from fire, electric shock, or falling objects.)

4. Do not install in a sooty, dusty, or humid location.

(Doing so may cause fire or electric shock.)

4 5

EE

Overview

Observation Camera is the monitoring camera

incorporated with the recent CCD that provides

the best monitoring function in connection with the

CCTV system equipment.

✔

Number of CCD pixels

•

320,000 pixels

✔

Power supply

•

SOC-C120P : DC12V From Monitor(SMO-150QP)

•

SOC-B120P

: DC12V From Monitor(SMO-120MP)

✔

Automatic function and special function

•

ATW

•

ELC(Electronic shutter iris)

•

Alarm Sensor input

•

Audio input

✔

The SOC-C120P is SMO-150QP(Monitor) only

✔

The SOC-B120P is SMO-120MP(Monitor) only

Part Names and Function

!@#$%^

PIN NUMBER SPEC

1 SPEAKER(HOT)

2 VIDEO_OUT

3GND

4 SPEAKER(COLD)

5

AUDIO_OUT/ALARM_OUT

6 12V DC

a

Lens

It has a focal length of 3.8mm and makes it possible

for you to observe a relatively wide area.

b

Microphone

Capable of picking up all sound in the vicinity of the

camera location and transmitting to the monitor.

6 7

EE

c

Camera fitting groove

Enables the camera to be fixed onto the bracket.

You may install it either above or below the camera if

necessary.

d

6-pin modular jack

Used to connect the camera to the monitor.

e

SENSOR jack

Used to connect the sensor to the camera.

f

Speaker

It outputs the sound signal which was transfered from

the monitor.

Installation

✔

Check what is inside the package

•

Check to see if the following parts are included in

the purchased package.

Camera Camera Mount Bracket

User’s Guide Alarm Terminal-Block Camera Cable

(Camera Kit option)

8 9

EE

✔

Notes on installation and usage

1.Users should not disassemble the camera from

the front direction.

2.Always handle the camera with care.

Please do not apply a shock or vibration as

much as possible and take cautions not to cause

damage or make a scratch on the camera due to

careless storage.

3.Please do not install the camera with the rainy

place or highly humid areas. And do not operate

the camera in the wet place.

4.Do not clean the camera body with the strong

abrasives or soaps. When the camera becomes

dirty, clean it with the dry rugs. Especially, make

sure to use the dedicated rugs for lens to clean

the dome cover.

5.Please select the camera in the cool area that is

not exposed to the direct sunlight. If you do, it

can cause bad effects on the product.

✔

Cable connection

Caution to install SOC-B120P/SOC-C120P out-

doors

•

SOC-B120P/SOC-C120P is designed to be protected

from the water drops which are falling on the

upper side of camera in a range of 15

°

.

(Dust-water protection level : IP42)

Therefore, be sure to install it in a location

which is fit in above condition when you install it

outdoor.

SOC-B120P/SOC-C120P

camera can be

attached to the wall,ceiling or shelf using the

camera mount bracket (SBR-110).

•

Choose an installation site that can sufficiently

support the weight of the equipments to be

installed.

•

Attach the camera mount bracket to the wall or

ceiling using the supplied three screws (M4 X L15).

•

Adjust the camera to target the video location

and tighten the bracket handle on the camera

mount bracket.

10 11

EE

4x15 sized screws

wall or ceiling

•

Connect the camera cable to the camera cable

jack on the camera,then connect,and the other

end of the cable to the monitor's channel input jack.

< SOC-B120P >

< SOC-C120P >

12 13

EE

•

An additional PIR sensor or external sensor can

also be connected.

•

The additional PIR sensor can be connected as

shown in the above graphic.

•

Sensor's trigger signal is NO (Normal Open).

•

Sensor is not supplied. (Sold separately)

✔

External terminal connecting method for camera

Camera alarm in jack

Sensor

in put

Specifications

SOC-C120P / SOC-B120P : Standard Camera

Model Name

SOC-C120P/ SOC-B120P

Broadcast System

SOC-C120P: PAL STANDARD

SOC-B120P: CCIR STANDARD

Imaging Device

SOC-C120P:

1/4 SUPER HAD IT CCD

SOC-B120P: 1/3” B/W IT CCD

Effective Pixels

500(H) x 582(V)

Synchronization

Internal

Resolution

SOC-C120P:

H :330 TV Lines,

V :350 TV Lines

SOC-B120P: H:380 TV Lines,

V:350 TV Lines

Signal Output

VBS 1.0 Vp-p(75ohm composite)

S/N Ratio

SOC-C120P: ≤48 dB

SOC-B120P: ≤50 dB

Minimum Object

SOC-C120P: 2lux(F2.0, 50 IRE)

Illumination

SOC-B120P: 0.2lux(F2.0, 50 IRE)

Gamma Correction

0.45

Lens

Focal Length (f) : 3.8mm,

Relative Aperture (F) : 2.0

Auto Exposure

Electronic Shutter lris

Audio

-40dB Condenser

Microphone Inclusion

I/O Connectors

Modular jack

Operating Temperature -10 ~ + 50

°C

Power Source

DC 12V (From Monitor)

Power Consumption Approx. 2W

Dimensions

57(W)X47.2(H)X100.5(L)

Weight

130g

14

E

R

êÛÍÓ‚Ó‰ÒÚ‚Ó ÔÓÎ¸ÁÓ‚‡ÚÂÎﬂ

SOC-C120P

SOC-B120P

Page is loading ...

Samsung SOC-B120P User manual

This manual is also suitable for

Samsung SOC-B120P User manual

Related papers

Other documents