Lutron Electronics EcoSystem 5-Series Installation guide

Brand
Lutron Electronics
Model
EcoSystem 5-Series
Type
Installation guide

Lutron Electronics EcoSystem 5-Series is a high-quality LED driver that offers a wide range of features and capabilities. With its advanced design, this driver provides reliable and efficient operation for your LED lighting system.

The EcoSystem 5-Series driver is designed for daisy-chain wiring, allowing you to connect multiple drivers together for larger lighting installations. This feature simplifies the wiring process and reduces the amount of cabling required.

In addition to daisy-chain wiring, the EcoSystem 5-Series driver also supports digital linking, which enables communication between compatible devices. This allows for remote control and monitoring of your lighting system, providing added convenience and flexibility.

Lutron Electronics EcoSystem 5-Series is a high-quality LED driver that offers a wide range of features and capabilities. With its advanced design, this driver provides reliable and efficient operation for your LED lighting system.

The EcoSystem 5-Series driver is designed for daisy-chain wiring, allowing you to connect multiple drivers together for larger lighting installations. This feature simplifies the wiring process and reduces the amount of cabling required.

In addition to daisy-chain wiring, the EcoSystem 5-Series driver also supports digital linking, which enables communication between compatible devices. This allows for remote control and monitoring of your lighting system, providing added convenience and flexibility.

English
LED Driver
Installation Guide
EcoSystem® 5-Series LED Driver
Driver Mounting
Remove lids before mounting. Avoid mounting driver close to heat source
such as light source.
Enclosure Mounting
Correct
Lutron Technical Support Hotline +44.(0)20.7680.4481
Lutron, EcoSystem, and ) are registered trademarks of Lutron Electronics Co., Inc.
Power Input and Digital Link Wiring
WARNING: Shock hazard. May result in serious injury or death.
Disconnect power before servicing or installing.
For proper wiring, follow wiring schematic on driver label. Torque range
on connector screws: 0.45 N•m to 0.50 N•m.
Load Wiring
Secure Wiring
Mains Wire Size:
Use 0.75 mm
2
– 2.50 mm
2
cable
(side view)
(top view)
Solid or stranded
copper wire
8 mm
Wire Size Digital Link
Length (max)
2.50 mm
2
500 m
1.50 mm
2
300 m
1.00 mm
2
200 m
0.75 mm
2
150 m
Ensure outer insulation extends across both rows of strain relief teeth.
Correct Incorrect
(insulation stripped too far)
Replace the lids to clamp the wires
in place.
Tighten the screws (0.5 N•m to
0.8 N•m) and tug gently on the wires
to ensure they are secure.
Use 0.75 mm
2
– 1.50 mm
2
cable.
+V / Red
15 m Max Cable Length
LED
light
source
www.lutron.com/europe
Lid screws
To secure mounting,
insert M3.5 screws here.
Daisy Chain Wiring
To EcoSystemR Digital Link
compatible devices.
Note:
For EcoSystemR daisy chain wiring, terminals can
accept two 0.75 – 1.50 mm
2
solid or stranded wires.
EcoSystemR Daisy Chain Wiring
Power Daisy Chain Wiring
To additional EcoSystemR
LED Drivers. (Maximum units
to be daisy chained: 20)
-V / Black
Incorrect
Use 0.75 mm
2
– 1.50 mm
2
cable
Note:
When placing multiple cables into the same strain relief,
all cable outside diameters must be the same.
N
L
N/C
N/C
E1
E2
Primary
Digital Bus
N/C
E1
E2
Digital Bus
N/C
E1
E2
Digital Bus
UNIT 1 UNIT 2
N/C
N
L
Primary
N/C
N
L
Primary
UNIT 1 UNIT 2
SELV Secondary
N/C
-V
N/C
+V
Refer to spec submittal for 15 m cable
wire gauge requirements.
041407b
P/N 041407b 01/2014
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Lutron Electronics EcoSystem 5-Series Installation guide

Brand
Lutron Electronics
Model
EcoSystem 5-Series
Type
Installation guide

Lutron Electronics EcoSystem 5-Series is a high-quality LED driver that offers a wide range of features and capabilities. With its advanced design, this driver provides reliable and efficient operation for your LED lighting system.

The EcoSystem 5-Series driver is designed for daisy-chain wiring, allowing you to connect multiple drivers together for larger lighting installations. This feature simplifies the wiring process and reduces the amount of cabling required.

In addition to daisy-chain wiring, the EcoSystem 5-Series driver also supports digital linking, which enables communication between compatible devices. This allows for remote control and monitoring of your lighting system, providing added convenience and flexibility.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents