© 2018
Order #XXXXX
Plan View
Perspective View
10’
10’
Scale: 18
VK-1127 General Layout
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
© 2018
Order #XXXXX Grid View
Locked layer contains
placeholder marks.
= 1 sq foot
© 2018
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2018
Order #XXXXX
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
4
13
2
Fold edges over.
Insert into
groove
of frame
SEG Installation
© 2018
Case 1 of 3
Order #XXXXX
Graphics
Lights
Setup Hardware
Top View of Each Level
Level 1 Level 2
2A 3
Level 3 Level 4 Level 5
2
5,5A 6,6A
Base
Plate
(Qty. 2)
Wings (Qty. 4)
Case Packing
© 2018
Case 2 of 3
Order #XXXXX Case Packing
Top View of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5
4A 43A
Assembled Workstation
Front Panel
7/10/11/11/Door
© 2018
Case 3 of 3
Order #XXXXX Case Packing
Top View of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7
7A/10A/11/11/Door8/9/11/11/11A8/9/11/11/11A
Shelf
Supports
ShelfShelf
Workstation
Top
Workstation
Top
12,12
12,12
Infills
(Qty. 2)
Shelf
Supports
Assembled Workstation
Side Panel
Assembled Workstation
Side Panel
Infills
(Qty. 2)
12,12
12,12
Assembled Workstation
Front Panel
© 2018
Step 1 of 4
Order #XXXXX
5
Bolt
Left Frame Right Frame
Bolt
Bolt
6
5A
2A
2
8A
7A
8A
7A
3
4A
4
8
7
8
7
11
1
6A
Item
1
2,2A
3,3A
4,4A
5,5A
6,6A
7,7A
8,8A
Qty.
3
1,1
1,1
1,1
1,1
1,1
2,2
2,2
Description
Base Plate
47.5” RR1252 Vertical Extrusion w/ A10 Clamps
47.5” RR1252 Vertical Extrusion
47.5” RR1252 Vertical Extrusion w/ A10 Clamps
47.5” TSP46 Curved Horizontal Extrusion
47.5” TSP46 Curved Horizontal Extrusion
47.5” TSP46 Vertical Extrusion
47.5” TSP46 Vertical Extrusion
Steps:
1) Attach base plates to verticals [2] [3] and [4], using bolts.
2) Attach extrusions [2 to 2A] [3 to 3A] and [4 to 4A], using
connectors. See Extrusion Connector detail.
See TSP46 Corner Connection and TSP46 Straight Connection
details for steps 3 and 4:
3) Assemble left frame extrusions [5] [5A] [7] [7A] [8] [8A].
4) Assemble right frame extrusions [6] [6A] [7] [7A] [8] [8A].
5) Attach left and right assembled frames between assembled
verticals [2/2A] [3/3A] and [4/4A]. Tighten set screws to secure.
6) Install SEG graphics to front of assembled frames. See
SEG Graphic Installation sheet for instruction. Completed Assembly
**
*
S
E
G
G
r
a
p
h
i
c
S
E
G
G
r
a
p
h
i
c
3A
Set Screws
PR53
Connector
Extrusion Connector
Slide upper extrusion
over connector and
rest on lower extrusion.
Secure with set screws.
*
To prevent product loss,
keep all screws attached
to connector after
disassembling.
*
Lock
Set Screw
Slide end of extrusion over
Lock. Tighten set screw to
secure extrusions together.
TSP46 Corner Connection
TSP46 Straight Connection
*
PR53
Connector
TSP46
TSP46
Insert connector into extrusions.
Secure with set screws.
Set Screw
To prevent product loss, keep all
screws attached to connector
after disassembling.
VK-1127 Backwall Assembly
© 2018
Step 2 of 4
Order #XXXXX VK-1127 Backwall Attachments
Monitor
Mount
Wing
Wing
Wing
Wing
Monitor
Mount
Completed Assembly
* *
**
Steps:
1) Attach monitor mounts to verticals [2A and [4A]. See Monitor Mount detail.
2) Attach wings to clamps on each side of assembled backwall.
See A10 Clamp detail.
3) Connect lights to top of assembled backwall. See Light Connection detail.
Knob
Set Screw
Connector
1) Slide connector of clamp
into extrusion groove.
2) Tighten set screw when
A10 is in desired location.
3) Insert wing into clamp.
4) Tighten knob on clamp
to secure wing in place.
A10 Clamp
A10 Clamp
Light Connection
Connect light to
horizontal where
desired and
tighten in place.
*
Monitor Mount
Slide connectors into groove
of vertical extrusion. Tighten
set screws to secure in place.
Attach monitor mount back
plate to connectors, using bolts.
*
Bolts
Monitor
Mount
Connectors
with Set
Screws
© 2018
Step 3 of 4
Order #XXXXX VK-1127 Workstation Assembly
Item
7,7A
8
9
10,10A
11,11A
12,12A
Qty.
1,1
2
2
1,1
4,4
4,4
Description
42”h GS220 Vertical Extrusion w/ Door Stop
42”h GS220 Vertical Extrusion
42”h GS220 Vertical Extrusion
42”h GS220 Vertical Extrusion w/ Door Hinge
13” Z45 Horizontal Extrusion
10” Z41 Horizontal Extrusion
Steps:
1) Assemble horizontal extrusions between vertical extrusions, inserting infills.
2) Connect doors to verticals [10] and [10A]. See Door Connection detail.
3) Attach assembled workstations to backwall verticals [2] and [4], using
standoff barrels & screw caps. See Workstation Attachment detail.
4) Connect shelf supports to Velcro on inside of assembled workstation.
5) Place shelf onto shelf supports.
6) Place workstation top onto verticals [11A] and [12A]. See Workstation Top Lock detail.
Completed Assembly
*
Left Workstation Right Workstation Shelf Support
Shelf
Workstation Top
7
7A
11 11
11A
11A
11 11
11A 11A
12 12
12 12
12A
12A 8
8
9
9
10
10A
I
nf
i
l
l
I
nf
i
l
l
I
n
f
i
l
l
I
n
f
i
l
l
I
nf
i
l
l
I
nf
i
l
l
I
n
f
i
l
l
I
n
f
i
l
l
V4
Workstation Attachment
*
Screw Cap
Standoff Z45
Slide connector into groove of vertical extrusion.
Tighten set screws to secure in place. Screw
standoff into connector. Attach workstation to
standoff using screw cap.
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Workstation Top Lock
12
*
Pin
Hole
Door
Hinge
Hinge
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
11A
11A
12A
12A
*
*
*
*
*
Door
Door
© 2018
Step 4 of 4
Order #XXXXX
USB Extension Cord
Completed Assembly
Base
Plate
Post
Plate
Clamshell
Hex
Nut
Steps:
1) Attach base plate to straight end of post, using bolt.
2) Attach plate to curved end of post, using bolt.
NOTE: Plate must rotate to left and right before installing clamshell.
3) Attach clamshell to plate, using hex nuts. See Clamshell Attachment detail.
4) Insert iPad in clamshell, then feed cords through holes. See
Cord Management for iPad detail.
Clamshell Attachment
Rotate clamshell
to turn iPad from portrait
to landscape orientation.
Cord from iPad
Cord Management For iPad
Attach iPad cord to supplied USB extension
cord. Feed USB cord through top hole of
post, then out bottom hole of post.
connect to power.
Cord
Access
iPad
Lock Lock
Clamshell
Foam Lining
Removed
Home Button Shield
Optional Cover for Home Button
1) Remove foam lining from inside bottom of
clamshell.
2) Attach Home Button Shield with double-sided
tape to inside of clamshell, keeping top of
shield flush with clamshell opening.
NOTE: This is a permanent fix and can’t be
easily removed.
MOD-1336 iPad Kiosk (Qty. 2)
/
