Classic Exhibits VK-2308 Setup Instructions

Brand: Classic Exhibits

Model: VK-2308

Type: Setup Instructions

Order #XXXXX

Completed Assembly

Item

1,2,3,4

5,6,7,8

1,2,3,4

5,6,7,8

Qty.

1,1,1,1

Description

45” TSP46 Vertical Extrusion

45” TSP46 Horizontal Extrusion

45” TSP46 Vertical Extrusion

45” TSP46 Horizontal Extrusion

Base Plate

656

7878

C Clamp Connector

Connector

Screw

Slide connector over verticals,

then secure with screws.

Keep all screws attached to

connector pieces when

disassembling, to prevent loss.

Setups:

1) Assemble TSP46 frames together, flat on floor.

See TSP46 Frame Assembly sheet.

2) Use C clamp connector to connect assembled

frames together. See C Clamp Connector detail.

3) Attach base plate [9] to verticals [1] and [3].

See Base Plate Attachment detail.

4) Install SEG graphic to assembled frames. See

SEG Installation sheet..

5) Connect lights to top of assembled frame. See

Light Connection detail.

1) Place key hole over fixed bolt on assembled

frame then push down.

2) Turn knob into assembled frame to secure.

Base Plate Attachment

Fixed

Bolt

Threaded

Hole

push keyhole down

Key Hole

Base Plate

Assembled

Frame

Knob

Light Connection

Connect light to

horizontal where

desired and

tighten in place.

****

VK-2308 Sunrise

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

TSP46 Profile

All knobs must be tightened securely to ensure a proper connection.

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

Corner

Connector Corner

Connector

Corner

Connector

Corner

Connector

COMPLETED ASSEMBLY

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

Straight Connection

3) Tighten all knobs to secure connection.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

Slide connector across seam of extrusions.

Tighten all knobs.

All knobs must be tightened securely to ensure a proper connection.

Straight Connector

2) Loosen all knobs, then slide straight

connector across the seam of extrusions.

TSP46 Frame Assembly

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab. Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Case 1 of 1

Order #XXXXX

Graphics

Setup Hardware

Top View of Each Level

Level 1 (Bottom Level) Level 2

9 9

1,2,3,4,5,6,7,8

Level 3

1,2,3,4,5,6,7,8

Case Packing

Classic Exhibits VK-2308 Setup Instructions

Classic Exhibits VK-2308 Setup Instructions

Classic Exhibits VK-2308 Setup Instructions

Related papers