CMP Bobé Scupper Installation guide

Brand: CMP

Model: Bobé Scupper

Type: Installation guide

SCUPPER WATER FEATURE

INSTALLATION INSTRUCTIONS

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

IMPORTANT SAFETY INFORMATION: READ AND FOLLOW ALL INSTRUCTIONS

Save these instructions. Leave manual with homeowner after installation.

Improper installation, adjustment, alteration, service, or lack of maintenance can cause injury or property damage. Read

the installation, operating, & maintenance instructions thoroughly before installing or servicing this equipment.

1. PRODUCT DETAILS

BONDING LUG

• All scuppers come with a bonding lug on the back.

• This is a grounding lug used to ground the scupper

INLET: All scuppers are manufactured with a 1 ½” NPT female inlet in the back

2. DIMENSIONS

A. SPECIFICATIONS

RADIUS SCUPPER

SMOOTH FLOW SCUPPER SMOOTH FLOW RADIUS SCUPPER

ARC SCUPPER

U-SHAPE SCUPPER WEDGE SCUPPER

TUNNEL SCUPPER

1/2 W

12"

“C” = 1" for 6" W

2" for above 6"

10.5""

WALL MOUNTED BOWL

NOTES:

1. INLET AND BRACKET DIMENSIONS/QUANTITY ARE SUBJECT TO CHANGE WITH CUSTOM ORDERS.

2. STANDARD INLETS ARE 1.5" FEMALE IN BACK.

3. STANDARD SIZES COME WITH 3 6" LONG 3/8" THICK MOUNTING BRACKETS ACROSS BACK TOP OF BOWL.

4. FLOW RATE IS 15-20 GPM/FT. STAINLESS STEEL NOT RECOMMENDED FOR SALT WATER ENVIRONMENTS.

5. INSTALLATION TO BE COMPLETED IN ACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS.

6. DO NOT SCALE DRAWING.

7. THIS DRAWING IS INTENDED FOR USE BY ARCHITECTS, ENGINEERS, CONTRACTORS, CONSULTANTS AND DESIGN PROFESSIONALS

FOR PLANNING PURPOSES ONLY. THIS DRAWING MAY NOT BE USED FOR CONSTRUCTION.

8. ALL INFORMATION CONTAINED HEREIN WAS CURRENT AT THE TIME OF DEVELOPMENT BUT MUST BE REVIEWED AND APPROVED BY

THE PRODUCT MANUFACTURER TO BE CONSIDERED ACCURATE.

9. CONTRACTOR'S NOTE: FOR PRODUCT AND COMPANY INFORMATION VISIT www.CADdetails.com/info AND ENTER

REFERENCE NUMBER 5059-012.

WALL MOUNTED BOWL

WALL MOUNTED BOWLS

5059-012

BOBE WATER & FIRE

3101 NORTH 29TH AVE

PHOENIX, AZ 85017

TOLL FREE: 1-888-388-2623

PHONE: (888) 388-2623

FAX: (602) 253-3496

www.bobewaterandre.com

REVISION DATE 01/27/2016

ISOMETRIC

SELECT DESIRED SIZE:

A = 12", B = 12"

CUSTOM SIZE (FILL IN CUSTOM DIMENSIONS):

A = ____________ B = ____________

SELECT DESIRED MATERIAL:

COPPER

STAINLESS STEEL

HAMMERED COPPER

OIL RUBBED BRONZE PATINA

(ADDED TO COPPER)

BLACK ONYX PATINA

(ADDED TO COPPER)

SELECT DESIRED QUANTITY:

_________________________

A = 24", B = 12"

7”

24”

A = 36", B = 12"

A = 12", B = 7"

A = 24", B = 7"

A = 36", B = 7"

STANDARD SIZE

SELECT DESIRED DIMENSIONS:

FIGURE 1

1. LEVELING

• All scuppers must be installed 1/8” OFF LEVEL down in the front

• This means the scupper should be pointed down towards the pool 1/8”

• The helps the water ow o the lip and reduces spill-back under the scupper

2. BOND BEAM

• Install either in the bond beam or on top

• If installing in the beam, notch out an extra 1” (one inch) around the scupper.

• The extra inch allows room for the scupper to be leveled at the nal installation

• The steel pattern should be oset by 3” to the bottom and by 1” outside the length of the scupper.

STEEL OFFSET

FIGURE 2

3. MASONRY FINISHING

• Ideally the scupper should be on site when the column or wall is being built.

• If the scupper is NOT on site, leave a 1” gap in the masonry to allow for leveling adjustments.

B. INSTALLATION

SCUPPER SHOULD BE

ANGLED DOWN 1/8"

STONE, TILE, ETC

D. PLUMBING

1. PLUMBING INSTALLATION

a. RECOMMENDED PLUMBING

• Use multiple pumps when installing multiple water features.

• The dedicated pump should be plumbed with a minimum of 2” pvc pipe.

• VGB compliant suction covers must be used, and they must be installed 18” above the bottom of the pool.

• A lter strainer is required between the pump and the waterfall.

b. BALANCING THE FLOW

• A 3-way valve is recommended after the pump to allow the ow to be regulated between the scupper and the

pool return. The recommended location for this valve is after the lter near the equipment pad.

• When plumbing two or more scuppers, follow all of the previous instructions with the addition of a 2-way ball

valve for each water feature. The valve is necessary to balance the water ow between the units. CMP ball valve

part numbers are 25800-151-000 for 1½” and 25800-210-000 for 2”.

• The dedicated pump should be plumbed with a minimum of 2” pvc pipe

PUMP

3-WAY VALVE

SUCTION LINE

SEPARATE RETURN

TO POOL

SCUPPER

FILTER/STRAINER

FIGURE 3

2. INLET PLUMBING

1. Single Inlet

a. Sizes below 24 inches wide have a single inlet

b. Plumb with a single ball valve for ow regulation (FIGURE 4)

2. Dual Inlet

a. 24 inch scuppers have two inlets

b. Plumb the two inlets into a Tee tting with a ball valve before the Tee (FIGURE 4)

3. Multiple Inlets

a. 36 inch scuppers have three inlets

b. Scuppers with three inlets should be plumbed into a manifold to balance the ow. A ball valve should be

plumbed inline before the manifold (FIGURE 4)

D. PLUMBING

BELOW 24" WIDE 24" WIDE 36" WIDE OR LARGER

FLOW

BELOW 24" WIDE

24" WIDE

36" WIDE OR LARGER

FLOW

BELOW 24" WIDE 24" WIDE

36" WIDE OR LARGER

FLOW

FIGURE 4

3. FLOW RATES

• Flow rates vary by product model and design

• Listed ow rates are per foot. (Example: 12” Radius Scupper is 15-20GPM, 24” Radius Scupper is 30-40GPM)

• Adjust the ow on site after installation with a valve to get the desired look at the water feature.

RADIUS SMOOTH FL SMOOTH RAD. ARC CANNON TUNNEL U-SHAPE WEDGE SLOT BOWL BOX

15-20 GPM 25-30 GPM 25-30 GPM 15-20 GPM 15-20 GPM 15-20 GPM 15-20 GPM 15-20 GPM 18-25 GPM 15-10 GPM 15-20 GPM

E. MATERIAL CARE GUIDE

COPPER

PATINA: Dark brown to green to blue. All copper products will patina. Patina is a natural process of oxidation where copper

reacts to the elements and produces a series of colors that build up in order to protect the copper. The nal color can vary

widely depending on location, environment and other factors.

WHAT COLOR WILL MY PRODUCT BE?

All products ship in their natural copper state. Depending on where they are stored or transported, patina may begin to

develop. It is very likely the color may change between manufacture and delivery and will continue to patina after installation.

Copper can be cleaned after installation to reset the patina process.

CLEANING

• Patina color may vary from piece to piece, even when delivered on the same day. If you prefer to restore the material after

installation, a cleaning solution such as TarnX® may be used.

• Hand Prints/Water Spots: Products develop hand prints from handling or water stains from water testing. The natural patina

process will cover up the markings as the whole piece begins to darken.

STAINLESS STEEL

PATINA

Stainless steel does not develop a patina.

CLEANING

• Stainless steel is steel that is “stain-less” however, this DOES NOT MEAN THAT STAINLESS STEEL WILL NEVER RUST OR

CORRODE. Stainless steel can show water spots and deposits of minerals or other natural substances that appear, orange,

white and/or brown. We suggest regular cleaning, at least once a month.

• Use distilled, soft or puried water (preferably warm) while cleaning and as a last rinse. Dry with a soft cloth.

• General maintenance and/or light buildup can be done with a soft cloth. Windex works well if you want to remove water

spots. Otherwise a mild soap or vinegar (1 part vinegar to 3 parts water) will remove light buildup.

• Try to go in the direction of the natural polishing grains

• Heavier build-up can be cleaned using very ne red Scotch-Brite™ cleaning pads.

• In many cases, cleaning over time will greatly reduce reappearance of build-up.

SALTWATER

Stainless steel is not warranted for use in or around salt water. Our products are made of 316 marine grade Stainless Steel. .

Stainless steel can get water spots and stainless steel can get deposits of minerals or other natural substances that appeared,

white and/or brown. If this happens you’ll need to clean the areas each time the build up occurs and after 3-6 cleanings the

problem areas should be free of any build up returning.

Record Information on this System Below & Keep for Your Records

Installer _______________________________________________________________

Purchased From _______________________________________________________

Installation Date _____________________________

Model Number ______________________________

Pool Size in Gallons __________________________

Customer Service & Tech Support

Toll Free: 1-800-733-9060

suppor[email protected]

Warranty Questions

[email protected]

Support Resources & Videos Online

c-m-p.com/support

SAVE THESE INSTRUCTIONS

CUSTOM MOLDED PRODUCTS | 36 HERRING ROAD, NEWNAN, GA 30265 | WWW.C-M-P.COM0220sb

CMP Bobé Scupper Installation guide

CMP Bobé Scupper Installation guide

CMP Bobé Scupper Installation guide

Related papers

Other documents