Eaton XV400 5.7" Operating Instructions Manual

Operating Instructions

12/2014 MN04802009Z-EN

replaces M000746

XV400 5.7"/8.4"

MICRO PANEL

Imprint

2 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

Manufacturer

Support

Original instructions

The German version of this document is the original instructions.

Translations of the original instructions

All non-German editions of this document are translations of the original instructions.

Editor

Monika Jahn

Brand and product names

All brand and product names are trademarks or registered trademarks of the owner concerned.

Copyright

None of this document may be reproduced or processed, duplicated or distributed by electronic

systems in any form (print, photocopy, microfilm or any other process) without the written permission of

Eaton Automation AG, St. Gallen.

Subject to modifications.

Eaton Automation AG

Spinnereistrasse 8-14

CH-9008 St. Gallen

Switzerland

www.eaton.eu

www.eaton.com

Region North America

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

www.eaton.com

Other regions

Please contact your local supplier or send an Email

to: [email protected]

Contents

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 3

Contents

1 General....................................................................................................................... 7

1.1 Purpose of these Operating Instructions..................................................................... 7

1.2 Comments about this document ................................................................................. 7

1.3 Additional documentation............................................................................................ 7

2 Device description .................................................................................................... 9

2.1 Device names ............................................................................................................. 9

2.2 Function ...................................................................................................................... 9

2.3 Intended use ............................................................................................................... 9

2.4 Device versions........................................................................................................... 9

2.5 Package contents........................................................................................................ 11

2.5.1 Package contents for devices with standard front....................................................... 11

2.5.2 Package contents for devices with 4-hole front........................................................... 11

2.5.3 Package contents for devices with stainless steel front.............................................. 12

2.6 Accessories................................................................................................................. 12

2.7 Designation ................................................................................................................. 12

3 Safety regulations ..................................................................................................... 13

3.1 General ....................................................................................................................... 13

3.2 Meaning of symbols .................................................................................................... 14

3.3 Mandatory requirements, personnel ........................................................................... 15

3.3.1 Work safety ................................................................................................................. 15

3.3.2 Qualification of personnel............................................................................................ 15

3.3.3 Operating Instructions ................................................................................................. 15

3.3.4 Installation, maintenance and disposal ....................................................................... 15

3.3.5 Prohibited use .............................................................................................................15

3.3.6 Requirements for proper operation ............................................................................. 16

3.4 Device related hazards ............................................................................................... 17

4 Operating and indication elements ......................................................................... 21

4.1 Operating and indication elements on the front .......................................................... 21

4.2 Operating elements on the service side...................................................................... 22

4.3 Indication elements on the service side ...................................................................... 23

5 Installation ................................................................................................................. 25

5.1 Safety regulations ....................................................................................................... 25

5.2 Requirements for the place of installation ................................................................... 26

5.2.1 Engineering conditions of acceptability by Underwriters Labaratories Inc. (UL)......... 26

5.2.2 Requirements for the mounting position ..................................................................... 26

5.3 Interfaces .................................................................................................................... 28

5.3.1 Overview of interfaces................................................................................................. 29

5.3.2 Preparation of cables with D-Sub connector............................................................... 30

5.3.3 Power supply...............................................................................................................32

5.3.4 RS232 (System Port) .................................................................................................. 33

5.3.5 Ethernet....................................................................................................................... 35

5.3.6 USB Device.................................................................................................................36

Contents

4 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

5.3.7 USB Host .................................................................................................................... 36

5.3.8 CAN............................................................................................................................. 37

5.4 Mounting .....................................................................................................................39

5.4.1 Fitting the communication module in the device ......................................................... 40

5.4.2 Mounting a device with standard front ........................................................................ 42

5.4.3 Mounting a device with 4-hole front ............................................................................ 45

5.4.4 Mounting a device with stainless steel front (standard mounting and mounting to IP65) 47

5.4.5 Mounting a device with stainless steel front (mounting to IP69K)............................... 50

6 Operation ................................................................................................................... 53

6.1 Safety regulations ....................................................................................................... 53

6.2 Starting the device ...................................................................................................... 54

6.3 Switching off the device .............................................................................................. 56

7 Maintenance and service.......................................................................................... 57

7.1 Safety regulations ....................................................................................................... 57

7.2 Maintenance................................................................................................................ 58

7.2.1 Cleaning the resistive touch ........................................................................................ 58

7.2.2 Recalibrating a resistive touch .................................................................................... 58

7.2.3 Cleaning the infra-red touch........................................................................................ 59

7.2.4 Recalibrating the infra-red touch ................................................................................. 60

7.2.5 Battery......................................................................................................................... 60

7.3 Service ........................................................................................................................ 61

7.3.1 Repairs........................................................................................................................ 61

7.4 Troubleshooting .......................................................................................................... 62

8 Storage, transport and disposal .............................................................................. 65

8.1 Safety regulations ....................................................................................................... 65

8.2 Storage........................................................................................................................ 65

8.3 Transport..................................................................................................................... 65

8.4 Disposal ...................................................................................................................... 66

9 Technical data ........................................................................................................... 67

9.1 Dimensions and weights ............................................................................................. 67

9.1.1 5.7" devices with standard or stainless steel front ...................................................... 67

9.1.2 5.7" devices with 4-hole front ...................................................................................... 68

9.1.3 8.4" devices................................................................................................................. 69

9.2 Display ........................................................................................................................ 70

9.2.1 5.7" devices XV-432-57; MC2-432-57 and XV-442-57; MC2-442-57 ......................... 70

9.2.2 5.7" devices XV-450-57 and XV-460-57 ..................................................................... 71

9.2.3 8.4" devices................................................................................................................. 71

9.3 Touch sensor .............................................................................................................. 72

9.3.1 Devices with resistive touch ........................................................................................ 72

9.3.2 Devices with infra-red touch........................................................................................ 72

9.4 System ........................................................................................................................ 72

9.5 Interfaces .................................................................................................................... 73

9.5.1 Power supply...............................................................................................................74

9.6 Enclosure ratings ........................................................................................................ 75

9.7 Agency approvals and standards................................................................................ 75

Contents

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 5

9.8 Applicable standards and regulations ......................................................................... 76

9.9 Ambient conditions...................................................................................................... 77

Contents

6 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

1 General

1.1 Purpose of these Operating Instructions

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 7

1 General

1.1 Purpose of these Operating Instructions

These Operating Instructions contain the information required for the correct and safe use of the

MICRO PANELs XV400 5.7"/8.4"; MC2 5.7". The Operating Instructions are part of the devices and

must therefore be kept nearby.

These Operating Instructions describe all aspects of the devices: transport, installation, commissioning,

operation, maintenance, storage and disposal. The operating system and the application software are

not described.

1.2 Comments about this document

Please send any comments, recommendations or suggestions relating to this document to info-auto-

[email protected].

1.3 Additional documentation

The following documents may be helpful in the use of the device in addition to this document:

[1] MN05010007Z-EN System Description Windows CE

(operation of the Windows CE operating system on MICRO PANELs)

[2] MN05010009Z-EN System Description Networks in Brief

(information on networks in general and on the integration of PCs and MICRO PANELs in

networks)

The documents can be downloaded from:

 www.moeller.net, «Support» section

 www.eaton.eu (search document No. via search field of the home page)

 www.eaton-automation.com, «DOWNLOADS» section



Read Chapter 3 Safety regulations,  13 before working with the device. This contains

important information for your personal safety. This chapter must be read and under-

stood by all persons working with this device.

WARNING

Incomplete copy of the Operating Instructions

Working with individual pages of these Operating Instructions may cause damage

to property or personnel by failure to observe safety-related information.

 Always work with the complete document.

1 General

1.3 Additional documentation

8 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

2 Device description

2.1 Device names

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 9

2 Device description

2.1 Device names

XV400 5.7"/8.4" and MC2 5.7" are two different names of equivalent products.

2.2 Function

MICRO PANELs XV400 5.7"/8.4"; MC2 5.7" can be used as HMI devices or as integrated HMI/PLC

devices.

2.3 Intended use

MICRO PANELs XV400 5.7"/8.4"; MC2 5.7" are primarily used in machine and system building. They

are designed exclusively for the visualization, operation and control of machines and systems. Any

other use must be agreed beforehand with the manufacturer.

2.4 Device versions

MICRO PANELs XV400 5.7"/8.4"; MC2 5.7" are available in the following versions:

Tab. 1 Device versions

Version with XV400 type MC2 type

Resistive touch 5.7", CSTN LCD display, standard front XV-432-57CQB-1-1x MC2-432-57CQB-1-1x

Infra-red touch 5.7", CSTN LCD display, standard front XV-442-57CQB-1-1x MC2-442-57CQB-1-1x

Infra-red touch 5.7", CSTN LCD display, 4-hole front XV-442-57CQB-1-2x MC2-442-57CQB-1-2x

Infra-red touch 5.7", CSTN LCD display, stainless steel

front

XV-442-57CQB-1-5x MC2-442-57CQB-1-5x

Resistive touch 5.7", TFT LCD display, standard front XV-450-57TQB-1-1x –

Infra-red touch 5.7", TFT LCD display, standard front XV-460-57TQB-1-1x –

Infra-red touch 5.7", TFT LCD display, stainless steel

front

XV-460-57TQB-1-5x –

Infra-red touch 8.4", TFT LCD display, standard front XV-460-84TVB-1-1x –

2 Device description

2.4 Device versions

10 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

Abb. 1 5.7" device with resistive touch and standard front Abb. 2 5.7" device with infra-red touch and standard front

Abb. 3 5.7" device with infra-red touch and 4-hole front Abb. 4 5.7" device with infra-red touch and stainless steel front

Abb. 5 8.4" device

2 Device description

2.5 Package contents

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 11

2.5 Package contents

The accessories supplied with the MICRO PANELs XV400 5.7"/8.4"; MC2 5.7" depend on the device

version.

2.5.1 Package contents for devices with standard front

Tab. 2 Package contents for devices with standard front

2.5.2 Package contents for devices with 4-hole front

Tab. 3 Package contents for devices with 4-hole front



If required, styluses in sets of 5 (ACCESSORIES-TP-PEN-5, Article No. 171192) and other

accessories can be ordered. Please contact the supplier.

Qty Designation

1 MICRO PANEL:

 XV-432-57CQB-1-1x or

 XV-442-57CQB-1-1x or

 XV-450-57TQB-1-1x or

 XV-460-57TQB-1-1x or

 XV-460-84TVB-1-1x or

 MC2-432-57CQB-1-1x or

 MC2-442-57CQB-1-1x

4 Retaining brackets with threaded pin for mounting the device

1 Sealing strip for mounting the device

1 Power supply connector

Qty Designation

1 MICRO PANEL:

 XV-442-57CQB-1-2x or  MC2-442-57CQB-1-2x

4 Countersunk screws for mounting the device

1 Front seal for mounting the device

1 Power supply connector

2 Device description

2.6 Accessories

12 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

2.5.3 Package contents for devices with stainless steel front

Tab. 4 Package contents for devices with stainless steel front

2.6 Accessories

Different accessories are available. Use only original accessories.

2.7 Designation

Nameplate A nameplate is fixed on the rear of the device in order to identify it. The nameplate contains the following

information:

 Manufacturer address

 Type designation

 Power supply required

 Part no. (Part-No or Art.-No)

 Serial no.

 Time of manufacturing (week/year)

 Approval mark and information to the approval

 Arrangement of interfaces and operating elements

 Permissible mounting options (top edge «Top»)

Support To ensure fast and optimum support always provide the support personnel with the following informa-

tion on the nameplate:

 Part no. (Part-No or Art.-No)

 Serial no.

Qty Designation

1 MICRO PANEL:

 XV-442-57CQB-1-5x or

 XV-460-57TQB-1-5x or

 MC2-442-57CQB-1-5x

8 Retaining brackets with threaded pin for mounting the device

1 Seal for mounting the device

1 Power supply connector



Order the accessories required from your supplier.

 Required accessories for:

- Mounting with increased protection class:

See Chapter 9.6 Enclosure ratings,  75.

- Use in a potentially explosive atmosphere:

See Chapter 9.7 Agency approvals and standards,  75.

 Required communication module

3 Safety regulations

3.1 General

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 13

3 Safety regulations

3.1 General

Hazards may still occur even though the device meets the current state of the art and complies with all

recognized safety requirements.

The device must only be installed and commissioned in perfect technical condition and in compliance

with this document.



Read this chapter before working with the device. This contains important information

for your personal safety. This chapter must be read and understood by all persons work-

ing with this device.

3 Safety regulations

3.2 Meaning of symbols

14 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

3.2 Meaning of symbols

The following symbols are used in this document according to the hazard level described:

The danger symbol used and the text indicate the actual danger and the related preventative measures.

DANGER

Signal word DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING

Signal word WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION

Signal word CAUTION

Indicates a potentially hazardous situation which, if not avoided, could result in minor

or moderate injury.

CAUTION

Signal word CAUTION without safety alert symbol

Indicates a situation which, if not avoided, could result in material damage.



Indicates useful information.

3 Safety regulations

3.3 Mandatory requirements, personnel

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 15

3.3 Mandatory requirements, personnel

3.3.1 Work safety

All applicable work safety regulations (in-house and national) must be observed.

3.3.2 Qualification of personnel

The personnel responsible for installation, operation, maintenance and service must be adequately

qualified. These persons must be sufficiently trained or instructed and they must be informed of all

hazards and risks associated with the device.

3.3.3 Operating Instructions

It must be ensured that any person working with the device in any phase of its lifespan has read and

understood the relevant sections of the Operating Instructions.

3.3.4 Installation, maintenance and disposal

It must be ensured that the device is properly connected, mounted, maintained and disposed of in

compliance with all relevant standards and safety regulations.

3.3.5 Prohibited use

The implementation of safety functions (relating to the protection of personnel and machinery) using the

device is prohibited.

WARNING

Incomplete copy of the Operating Instructions

Working with individual pages of these Operating Instructions may cause damage

to property or personnel by failure to observe safety-related information.

 Always work with the complete document.

3 Safety regulations

3.3 Mandatory requirements, personnel

16 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

3.3.6 Requirements for proper operation

The following points must be observed so that the device meets the contractual requirements:

 Only qualified personnel may work with the device.

 These persons must have read the Operating Instructions and must observe the requirements

described.

 The ambient conditions stated must be observed. See Chapter 9.9 Ambient conditions,  77.

 The maintenance work must be carried out correctly.

 Potentially explosive atmosphere, Zone 22:

The ground resistance of accessible metal parts must be less than 10

9

ohms.

No liability is accepted for damage, consequential damage and accidents caused by the following:

 Failure to observe work safety regulations

 Failure or malfunction of the device

 Improper handling or use

 Failure to observe the Operating Instructions

 Conversions, modifications and repairs to the device



Repairs, see Chapter 7.3.1 Repairs,  61.

3 Safety regulations

3.4 Device related hazards

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 17

3.4 Device related hazards

DANGER

Explosion hazard

Death, serious injury or material damage may occur if an electrical plug connection

is removed in a potentially explosive atmosphere during operation or if the device is

subjected to hazardous knocks.

 Only use the device in the following environments:

- Environments not subject to explosion hazards

- Potentially explosive atmosphere, Zone 22 (according to ATEX 94/9/EC)

 Potentially explosive atmosphere, Zone 22:

The ground resistance of accessible metal parts must be less than 10

9

ohms.

 When used in potentially explosive atmosphere, Zone 22, the environment has

to be designed to avoid any bunch discharge.

 Prevent the device from being subjected to hazardous knocks.

 Only operate the device in potentially explosive atmospheres if it is correctly

mounted.

 Switch off the device before removing the plug connections.

WARNING

Live parts in the device

When the device is opened, there is a risk of electric shock if live parts are touched.

 The device must not be opened.

WARNING

Potential equalization currents

Large equalization currents between the protective ground systems of different de-

vices may cause operational malfunctions due to signal interference and may even

cause fires.

 If necessary, a potential equalization conductor should be installed parallel to the

cable. This should have a cross-section that is a multiple of the cable shield.

CAUTION

Electrostatic discharge

Electrostatic discharge may damage or destroy electronic components.

 Avoid contact with components (such as connector pins) that are susceptible to

electrostatic discharge.

 Discharge (by touching a grounded metal object) any static charge accumulated

in your body before touching the device.

3 Safety regulations

3.4 Device related hazards

18 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

CAUTION

Non-isolated interfaces

The device may be damaged due to potential differences.

 The GND terminals of all bus stations must be connected.

CAUTION

Sensitive resistive touch surface

Damage to the resistive touch due to the use of pointed or sharp objects.

 Only activate the resistive touch with your finger or a stylus.

 When wearing gloves, ensure that these are clean. They must not be covered

with abrasive dust or sharp particles.

CAUTION

Data loss

During a write operation, the CF card may lose data or may be destroyed if it is re-

moved or if there is a power failure.

 Always secure CF cards with the CF slot cover.

 Avoid write operations to CF cards. Reasons:

- The number of write cycles possible on CF cards is limited.

- A power failure during write operations will most likely lead to loss of data.

 Only remove the CF card when the device is in a de-energized state.

 Before switching off, ensure that no software write operations to the CF card are

in progress («CF ACT» LED must not be lit).

CAUTION

Device condensation

If the device is or was exposed to climatic changes (temperature fluctuation, air hu-

midity) moisture can form on or in the device (device condensation). In this case,

there is a risk of short-circuit.

 The device must not be switched on when device condensation is present.

 If condensation is present on the device, or if it was exposed to temperature fluc-

tuations, it must be allowed to adjust to room temperature (do not expose the de-

vice to the direct heat of heating devices) prior to commissioning.

CAUTION

UV light

When exposed to UV light, plastics can embrittle and the lifespan of the device is

reduced.

 Protect the device against direct sunlight and lamps with UV rays.

3 Safety regulations

3.4 Device related hazards

MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com 19

CAUTION

Cleaning the device

Damage to the device due to the use of pointed or sharp objects or by liquids.

 Do not use any pointed or sharp objects (e.g. knife) for cleaning.

 Do not use any aggressive or abrasive cleaning agent or solvent.

 Avoid any liquid entering the device (risk of short-circuit).

3 Safety regulations

3.4 Device related hazards

20 MICRO PANEL XV400 5.7"/8.4" 12/2014 MN04802009Z-EN www.eaton.com

Page is loading ...

Eaton XV400 5.7" Operating Instructions Manual

This manual is also suitable for

Eaton XV400 5.7" Operating Instructions Manual

Related papers

Other documents