Quick Reference
Contents
Loading paper and specialty media...............................................3
Loading the paper tray........................................................................................................................................................3
Clearing jams.......................................................................................7
200–201 paper jam................................................................................................................................................................7
202 paper jam.......................................................................................................................................................................10
241 paper jam.......................................................................................................................................................................13
251 paper jam.......................................................................................................................................................................14
Contents
2
Loading paper and specialty media
Loading the paper tray
Do not load the paper tray while a job prints or while Busy appears on the display. Doing so may cause a paper jam.
1 Pull the paper tray completely out.
2 Squeeze the width guide tabs on the right guide as shown, and slide the width guides to the sides of the tray.
The width guides move in unison.
Loading paper and specialty media
3
3 Squeeze the length guide tabs together as shown, and then slide the length guide to the correct position for the
paper size. Use the size indicators on the bottom of the tray to help position the guide.
If you are loading a longer size of paper, then squeeze the length guide tab and slide the length guide backward
to the correct position for the paper size. The tray extends backward as shown.
4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the
edges on a level surface.
Loading paper and specialty media
4
5 Load the paper stack toward the back of the tray as shown with the recommended print side facedown.
Note: The maximum fill line on the side of the width guide indicates the maximum height for loading paper. Do
not overload the tray.
Load letterhead with the print side facedown and the top edge of the sheet toward the front of the tray.
6 Squeeze the width guide tabs on the right guide, and then slide the width guides to lightly touch the side of the
stack.
Loading paper and specialty media
5
7 Insert the paper tray.
8 If the paper type you loaded differs from the type that was previously loaded in the tray, then change the Paper
Type setting for the tray.
Loading paper and specialty media
6
Clearing jams
200–201 paper jam
200 paper jam
1 Remove the tray from the printer.
Clearing jams
7
2 Remove the jam if you see it here.
3 If you do not see it, see “201 paper jam” on page 8.
201 paper jam
1 Open the front door, and then remove the photoconductor kit and toner cartridge.
Clearing jams
8
2 Lift the flap at the front of the printer, and remove any jammed sheets.
3 Align and insert the photoconductor kit and toner cartridge.
4 Close the front door.
5 Insert the tray.
6 Press .
Clearing jams
9
202 paper jam
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
1 Open the front door, and then remove the photoconductor kit and toner cartridge.
Clearing jams
10
2 Lift the flap at the front of the printer, and then remove any jammed sheets.
Clearing jams
11
3 Open the rear door.
4 Remove the jam.
5 Close the rear door.
6 Align and insert the photoconductor kit and toner cartridge.
7 Close the front door.
8 Press .
Clearing jams
12
241 paper jam
1 Remove the tray from the printer.
2 Remove the jam.
3 Insert the tray.
4 Press .
Clearing jams
13
251 paper jam
A sheet of paper or specialty media failed to feed completely from the manual feeder. Part of it may be still visible. If
it is visible, then gently pull the jammed sheet from the front of the manual feeder.
If the sheet is not visible, then complete the following steps:
1 Remove the photoconductor kit and toner cartridge.
Clearing jams
14
2 Lift the flap at the front of the printer, and then remove any jammed sheets.
3 Align and insert the photoconductor kit and toner cartridge.
4 Press .
Clearing jams
15
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Lexmark X204N series Function Manual
- Type
- Function Manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Lexmark 260dn - E B/W Laser Printer Reference guide
-
Lexmark 34S0500 User manual
-
Lexmark E360d Series User manual
-
Lexmark 430 User manual
-
Minolta E260 Series User manual
-
Lexmark 34S0600 User manual
-
-
Lexmark 34A0252 User manual
-
-