Legrand DLM Wireless Quick Start User guide

Brand: Legrand

Model: DLM Wireless Quick Start

Type: User guide

Wattstopper

Wireless DLM Configuration App Quick Start Guide

Download the App

The DLM Conguration App is accessible by download through

the Apple

App Store or Google

Play Store for Android

Search for “DLM Conguration” by Legrand. Install and launch

the app on your smart phone or tablet.

NOTE: The DLM App software and hardware requirements:

• Android OS 4.4 (KitKat) or later; Recommended Android

OS 7 (Nougat)

• Hardware iOS manufactured after 2013 only (iPhone 5+

and newer) iOS10 or later, recommended iOS11

• Device Bluetooth™ 4.2 and higher

• Wireless DLM Device Firmware: Version 10.14 or newer

Overview

This quick start guide will help you obtain the wireless DLM Conguration App, set up an authorized account, and establish your site

in preparation for connecting devices to create wireless rooms. Further customize your site through device parameter settings, create

and organize scenes, and keep the system current with wireless rmware updates. For more details on the app, download the user

guide at www.legrand.us/wattstopper.

Create An Account

Press the Create New Account option (requires Internet

access). You will need to create an account. Fill in the screen

elds. It is important to associate a phone number that can

receive texts for system information feedback. Tap Create

Account to nalize.

IMPORTANT: Wattstopper recommends creation of an

authorized account before pairing. Although it is possible to do

basic pairing without an account, an authorized account allows

you to fully secure the site to the cloud and also provides for

full conguration of DLM rooms, including editing of device

parameters.

You can call Wattstopper at 1.888.538.6070 to nd out about

your authorization status.

DEVICE PAIRING THROUGH AUTHORIZED SITES

Prepare Devices

If devices have not already been installed, prepare devices by

adding batteries and installing them according to the device’s

installation instructions. All devices should be 10 pressed and

ready to go.

NOTE: If DLM wireless equipment is being used repeatedly

for demo purposes, previously created networks should

be decommissioned and app data should be cleared. For

instructions, see page 10.

IMPORTANT:

Set up your account and obtain authorization (steps 2-4) before

proceeding.

DLM Wireless Quick Start Guide

Enter Sites

Open the DLM Conguration App and choose Sites from

the main dashboard. Create a new site or select an existing

site.

NOTE: Using Sites is the standard method for wireless DLM

project creation and management and also begins the process

of cloud site backup.

Create A Site

To create a new site, tap the + circle in the lower right hand

corner to select Create Site +.

Obtain Account Authorization

Once you have received authorization and log back into the

DLM Conguration App, you will receive a notication verifying

authorization. You will also see a check mark on the dashboard

next to Account Status.

DLM Wireless Quick Start Guide

Establish Areas and Rooms

Tap the three ellipses next to Building. Tap Edit Name to

enable the keyboard, change the building name text, and then

tap the check mark to save changes.

Tap Add Area under the ellipses of the building name to begin

creating areas within the building. This dialog box will visually

reect which area the new area will be nested under. Name the

new area and tap OK to save changes. You can add multiple

areas, or create sub-areas under areas.

Fill the Fields

Fill in the elds for the new site. The name, city and state are

required to create a site. The other information is helpful to

create a complete prole but is not required.

Tap Create when nished to complete the site set up. Repeat

this process for each site creation.

NOTE: Recently viewed sites will be located under the main

dashboard for convenience. Tap on a site tile at the sites level

to access its dashboard.

Create A Room Network and Add Controller

Make sure all devices are awake by single pressing each of

their conguration buttons. From the Networks page, tap

the Add Network + button and select Create new network.

Select the room controller that will be used to begin the pairing

process from the available list that is shown.

NOTE: The four digit identier (XX:XX) for each device in

the app coincides with the four digit code on the device itself.

Please ensure you are choosing the correct device.

DLM Wireless Quick Start Guide

Wake Up Devices

Wake up devices by pushing the cong button once. This

powers up the device for 5 minutes which gives you enough

time to pair the device through the app.

Wake all battery-powered devices within arms reach before

installation or access installed devices via ladder.

Wireless Dimming Wall Switch

Remove switch plate and with a pen point, push the

conguration button one time to awake.

Sensors

Push the conguration button on the outside cover

one time to awake.

NOTE: FACTORY DEFAULT: To reset the controller or any

device to factory default, press the conguration button

consecutively 10xs.

CONFIG

BUTTON

CONFIG

BUTTON

WIRELESS DIMMING WALL SWITCH

SENSORS

ROOM CONTROLLER

X10

LMPC-600 LMPX-600

LMRC-611

LMDM-601 LMSW-605

Add Devices

Check the devices you would like to add by tapping the white

box in the device tile. Select the green circle at the bottom-right

to add the devices to your network. Devices will pair and reset.

Select the Next button then select the Return To Networks

button.

DLM Wireless Quick Start Guide

Add Devices to Areas

Return to the Site level . At the desired area level, tap the

three ellipses and select Add Devices.

Select Devices and Finalize

Check the devices you would like to add to the room by tapping

the white box in the device tile. Select the green circle at the

bottom-right to add the devices to your room.

Demo

At this point you can demo whatever is needed with the

network (RC, parameters, scenes, etc.) When nished, select

the network used from the networks view.

NOTE: If DLM wireless equipment is being used repeatedly

for demo purposes, previously created networks should

be decommissioned and app data should be cleared. For

instructions, see page 10.

DLM Wireless Quick Start Guide

Set Device Parameters and Sequence of

Operations (SoO)

With an authorized account, you can now set parameters for

devices, and create scenes, etc. Tap on the “Room Controller”

tile to edit parameters for devices linked to the room

controller. Tap on the Change Parameters under Settings to

access the parameter options. Some of the parameters that

can be set through the room controller are:

• Trim Levels

• Occupancy Delays

• Vacancy Timeouts

• Daylight Harvesting

Customize

A secure site and network has now been created. The next steps are quick overviews to the Device Parameters, Scenes, Room/

Device, Networks, Site Synchronization, and Site Information icons located along the bottom. See the DLM Conguration App User’s

Guide for further detail.

Scenes Overview

In the Scenes section you can view, edit, or create scenes.

Add new categories by pressing the “+” button. Selecting a

category will display all scenes in that category. Tap on a scene

to view or edit its details. To add a new scene click on the “+”

button.

Room Overview

Sites displays the tree structure view of your site that you

have established. Edit and add areas, rooms, and devices

within the site. View additional information about a specic

room such as devices, loads, and scenes by selecting the

desired location. Toggle between device and room view

by tapping the desired icon at the top right.

DLM Wireless Quick Start Guide

Networks View Overview

By tapping on the Networks icon , you can view all visible

DLM networks associated with the selected site and the

number of devices that have been added at a quick glance.

To view unpaired devices alongside devices on the site, select

“Unsecured Networks” from the lter menu.

Site Synchronization Overview

To access Site Synchronization, tap . In order to keep all

projects up to date, changes made are uploaded to the cloud.

You can see the status of items that are both pending changes

on the cloud, or items you have updated that need to be sent to

the cloud.

Site Information Overview

Tap to access Site Information. View demographic

information about the site such as its address, contact info,

code compliance standard, etc. To edit this information, tap the

“edit” icon at the top right of the page.

DLM Wireless Quick Start Guide

Enter Quick Pair and Prepare Devices

After setting up an account, tap the Quick Pair button

from the dashboard.

If devices have not already been installed, prepare devices by

adding batteries and installing them according to Wattstopper’s

instructions. All devices should be 10 pressed and ready to go.

See page 4 for details.

Quick Pair Process

Create A Room Network and Add Controller

Make sure all devices are awake by single pressing each of

their conguration buttons. From the Networks page, tap

the Add Network + button and select Create new network.

Select the room controller that will be used to begin the pairing

process from the available list that is shown.

NOTE: The four digit identier (XX:XX) for each device in

the app coincides with the four digit code on the device itself.

Please ensure you are choosing the correct device.

Add Devices

Check the devices you would like to add by tapping the white

box in the device tile. Select the green circle at the bottom-right

to add the devices to your network. Devices will pair and reset.

Select the Next button then select the Return To Networks

button.

DLM Wireless Quick Start Guide

Pairing Process Status

The app will begin the pairing process and an active status

screen will show the progress. A conrmation screen will inform

you when successful pairing has occurred and a new network

has been established.

New Network

Upon completion a new non-secured network will appear in

the networks list containing the last four numbers of the mac

address of the controller used.

DLM Wireless Quick Start Guide

800.879.8585

www.legrand.us/wattstopper

28654 Rev. 2 08/2019

Wireless DLM COnfiguration App

Quick Start Guide

The Bluetooth

word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of

such marks by Legrand is under license. Other trademarks and trade names are those of their respective owners.

Google Play and the Google Play logo are trademarks of Google Inc.

The Apple logo, iPhone, iPod touch, and iTunes are trademarks of Apple Inc., registered in the U.S. and other

countries.

Select the Network to Decommission

By tapping on the Networks icon , access the networks and

select the network to decommission. Tap the three ellipses and

select Decommission Network.

Conrm Deletion

Tap OK to conrm decommissioning. The app will remove

devices from the network.

Clear App Data

Return to the main dashboard. Tap the “menu” button (three

lines) to access the pop-up menu and select Settings. Tap

About and tap the Clear All App Data bar in the window.

Decommissioning A Network and Clearing App Data

It is important to decommission a network and clear app data when using wireless devices repeatedly for demo purposes.

Legrand DLM Wireless Quick Start User guide

Legrand DLM Wireless Quick Start User guide

Legrand DLM Wireless Quick Start User guide

Related papers

Other documents