Intel PMB-601LF User manual

USER’S

MANUAL

PMB-601LF

Intel

®

Core 2 Duo

ATX Motherboard

With VGA/Sound/2LAN

PMB-601LF M1

Copyright Notice

PMB-601LF Intel® Core 2 Duo

ATX Motherboard

With VGA/ Sound/ 2LAN

OPERATION MANUAL

COPYRIGHT NOTICE

This operation manual is meant to assist both Embedded Computer

manufacturers and end users in installing and setting up the system. The

information contained in this document is subject to change without any

notice.

This manual is copyrighted in January, 2007. You may not reproduce or

transmit in any form or by any means, electronic, or mechanical, including

photocopying and recording.

ACKNOWLEDGEMENTS

All trademarks and registered trademarks mentioned herein are the

property of their respective owners.

CE NOTICE

This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

Copyright Notice

FCC NOTICE

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment not

expressly approve by the party responsible for compliance could void

your authority to operate such equipment.

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual ........................................................ 1-2

1-2 System Specification ...................................................... 1-3

1-3 Safety Precautions ......................................................... 1-6

CHAPTER 2 HARDWARE CONFIGURATION

2-1 Jumper & Connector Quick Reference Table ................ 2-2

2-2 Component Locations .................................................... 2-3

2-3 How to Set the Jumpers ................................................. 2-4

2-4 COM Port Connector ……..…………………………... 2-6

2-5 COM3 RI & Voltage Selection …………..……………. 2-8

2-6 COM4 RI & Voltage Selection ……………………… 2-9

2-7 RS232/422/485(COM2) Selection ................................ 2-10

2-8 Keyboard and PS/2 Mouse Connector .....................….. 2-11

2-9 Reset Connector ............................................................ 2-11

2-10 Hard Disk Drive LED Connector .................................. 2-12

2-11 ATX Power Button ….................................................... 2-12

2-12 External Speaker Connector .......................................... 2-12

2-13 PLED Connector …….................................................... 2-13

2-14 KeyLock Connector ..………………………………… 2-13

2-15 External SMI Connector ……………………………… 2-13

2-16 Clear CMOS Data Selection ………………………… 2-14

2-17 CPU Fan Connector ………………………………….. 2-14

2-18 System Fan Connector ………………………………… 2-15

2-19 Power Fan Connector ………………………………….. 2-15

2-20 NB Fan Connector …………………………………….. 2-15

2-21 VGA Connector …………………..…………………… 2-16

2-22 Serial ATA Connector ………………………………… 2-17

2-23 Floppy Disk Drive Connector ....................................... 2-19

2-24 Printer Connector .......................................................... 2-20

2-25 Universal Serial Bus Connector ……………………… 2-21

2-26 IrDA Connector ………………………………………. 2-22

2-27 USB & LAN Connector ……………………………… 2-23

2-28 ATX Power Connector ………………………………. 2-25

2-29 Sound Connector ……………………………………… 2-26

2-30 CD Audio-In Connector ………………………………. 2-27

2-31 Memory Installation ………………………………….. 2-27

Contents

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction …………..........................................…....... 3-2

3-2 VGA Driver Utility ……………………………….…… 3-3

3-3 Flash BIOS Update ..............................................…....... 3-4

3-4 LAN Driver Utility …...........................................…...... 3-6

3-5 Sound Driver Utility …………………………………… 3-7

3-6 Intel Chipset Software Installation Utility …..……..….. 3-8

3-7 USB2.0 Software Installation Utility ………………….. 3-9

3-8 Watchdog Timer Configuration ……………………….. 3-10

CHAPTER 4 AWARD BIOS SETUP

4-1 Introduction ................................................................... 4-2

4-2 Entering Setup ............................................................... 4-3

4-3 The Standard CMOS Features ………............................ 4-4

4-4 The Advanced BIOS Features ....................................... 4-8

4-5 Advanced Chipset Features ........................................... 4-12

4-6 Integrated Peripherals …............................................... 4-14

4-7 Power Management Setup ............................................. 4-19

4-8 PNP/PCI Configuration …............................................. 4-21

4-9 PC Health Status …….................................................... 4-23

4-10 Frequency Control ....................................…………...... 4-24

4-11 Load Fail-Safe Defaults ................................................. 4-25

4-12 Load Optimized Defaults .........................................…. 4-25

4-13 Password Setting ……………………………………… 4-26

4-14 Save & Exit Setup ......................................................... 4-27

4-15 Exit Without Saving ………………………………… 4-28

APPENDIX A EXPANSION BUS

PCI Bus Pin Assignment ..............................................…......... A-2

APPENDIX B TECHNICAL SUMMARY

Block Diagram ........................................................................... B-2

Interrupt Map ............................................................................ B-3

RTC & CMOS RAM Map ........................................................ B-4

Timer & DMA Channels Map .................................................. B-5

I/O & Memory Map ...............................................…................ B-6

Page:1-1

INTRODUCTION

This chapter gives you the information for PMB-601LF. It also

outlines the System specifications.

Section includes:

z About This Manual

z System Specifications

z Safety Precautions

Experienced users can skip to chapter 2 on page 2-1

for a Quick Start.

CHAPTER

1

Chapter 1 Introduction

Page: 1-2

PMB-601LF USER

′

S MANUAL

1-1. ABOUT THIS MANUAL

Thank you for purchasing our PMB-601LF Intel® Core 2 Duo ATX

Motherboard enhanced with VGA/Sound/2LAN, which is fully PC / AT

compatible. The PMB-601LF provides faster processing speed, greater

expandability and can handle more tasks than before. This manual is

designed to assist you how to install and set up the system. It contains four

chapters. The user can apply this manual for configuration according to the

following chapters:

Chapter 1 Introduction

This chapter introduces you to the background of this manual, and the

specifications for this system. The final page of this chapter will indicate

how to avoid damaging this board.

Chapter 2 Hardware Configuration

This chapter outlines the component locations and their functions. In the

end of this chapter, you will learn how to set jumper and how to configure

this card to meet your own needs.

Chapter 3 Software Utilities

This chapter contains helpful information for proper installations of the

VGA utility, LAN utility, Sound utility, and Flash BIOS Update. It also

describes the Watchdog-timer configuration.

Chapter 4 Award BIOS Setup

This chapter indicates you how to set up the BIOS configurations.

Appendix A Expansion Bus

This Appendix introduces you the expansion bus for 1 x PCI-E16 BUS, 1

x PCI-E4 BUS, 4 x PCI Bus and 1 x ISA BUS.

Appendix B Technical Summary

This section gives you the information about the Technical maps.

Chapter 1 Introduction

PMB-601LF USER

′

S MANUAL

Page: 1-3

1-2. SYSTEM SPECIFICATIONS

z CPU (mPGA775):

Intel® Celeron®-D, Pentium® 4, Pentium®-D, Core 2 Duo processor in

mPGA775 Socket.

2.8~3.8 GHz clock generator for Pentium 4

1.86~2.66GHz clock generator for Core 2 Duo

Front Side Bus 533/667/800/1066 MHZ.

Auto detect voltage regulator.

z CHIPSET :

Intel Q965 + ICH8DO+FWH

z MEMORY :

Supports up to 8GB DDR SDRAM.

Four 240-pin DDR2 DIMM sockets on board.

z CACHE :

Built-in CPU.

z REAL-TIME CLOCK :

Build in South Bridge.

z BIOS :

Phoenix-AwardBIOS™ for plug & play function

.

8Mb with VGA BIOS.

Easy update 1MB flash EEPROM.

Support S/IO Setup.

z KEYBOARD CONNECTOR :

Mini DIN connector.

Supports for AT/PS2 keyboard.

z MOUSE CONNECTOR :

Mini DIN connector.

Supports for PS/2 Mouse.

z BUS SUPPORT :

1 PCI-E16 Slot, support Graphic Card

1 PCI-E4 Slots, support I/O card

4 PCI Slots

Chapter 1 Introduction

Page: 1-4

PMB-601LF USER

′

S MANUAL

1 ISA Slot

z DISPLAY :

Built-in Intel Q965, support for CRT.

Onboard 15-pin VGA D-SUB connector, support for resolution on SVGA

Monitor.

z SATA INTERFACE :

6 SATA ports, support RAID 0,1,5,10.

z SERIAL PORT :

Four serial connectors.

COM1/3/4 for RS-232, COM2 for RS-232/422/485.

COM3/4 can output +5V or +12V, and use jumper settings.

z FLOPPY DISK DRIVER INTERFACE :

Support up to two Floppy Disk Drives, 3.5" and 5.25" (360K / 720K / 1.2M /

1.44M / 2.88M).

z USB CONNECTOR :

Support up to ten USB 2.0 ports.

4 ports with LAN1/ LAN2 on rear panel.

6 ports with external 2.54 connector 2x5-pin headpin.

z LAN ADAPTER :

Dual ports, Intel® 82573V x 2, 10/100/1000 BaseT Ethernet.

LAN1: 10/100/1000 BaseT Ethernet

LAN2: 10/100/1000 BaseT Ethernet

Support wake-on-LAN function.

z SOUND :

Realtek ALC262A (HD Codec), including SPDIF.

Fully Compliant HD Analog I/O Component

16-Bit Stereo Full-Duplex Codec

Four Analog Line-level Stereo Inputs for Connection.

High Quality CD Input with Ground Sense

Stereo Line-Level Output

Interface: Line-In, Line-Out, Microphone, and CD Audio-In.

Chapter 1 Introduction

PMB-601LF USER

′

S MANUAL

Page: 1-5

z HARDWARE MONITORING FUNCTION :

Monitor Voltage, CPU temperature, & Cooling fan.

If CPU Temperature is over setting, the buzzer will send out a warming (only

under DOS system).

z IRDA PORT :

5-pin Infrared port, support IrDA v1.0 SIR protocol

z PARALLEL PORT :

SPP / ECP / EPP Function.

1 port, bi-directional parallel port.

z GREEN FUNCTION :

Controlled by hardware and software.

z LED INDICATOR :

System power

Hard Disk access (SATA)

z DMA CONTROLLER :

82C37 x 2

z DMA CHANNELS :

7

z INTERRUPT CONTROLLERS :

82C59 x 2

z INTERRUPT LEVELS :

15

z OPERATING TEMPERATURE :

0 to 60°C.

z BOARD DIMENSIONS :

305mm x 344mm, 12” x9.61”

z BOARD NET WEIGHT :

810 gram.

Chapter 1 Introduction

Page: 1-6

PMB-601LF USER

′

S MANUAL

1-3. SAFETY PRECAUTIONS

Follow the messages below to avoid your systems from damage:

1. Keep your system away from static electricity on all occasions.

2. Prevent electric shock. Don‘t touch any components of this card when the

card is power-on. Always disconnect power when the system is not in use.

3. Disconnect power when you change any hardware devices. For instance,

when you connect a jumper or install any cards, a surge of power may

damage the electronic components or the whole system.

Page 2-1

HARDWARE

CONFIGURATION

** QUICK START **

CHAPTER

2

Helpful information describes the jumper & connector settings, and

component locations.

Section includes:

z Jumper & Connector Quick Reference Table

z Component Locations

z Configuration and Jumper settings

z Connector’s Pin Assignments

Chapter 2 Hardware Configuration

Page: 2-2

PMB-601LF USER

′

S MANUAL

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

COM Port Connector ....................…..................………

…………………………………..

COM1, COM2

COM3, COM4

COM3 Port RI/Voltage Selection ……………………..

JP6

COM4 Port RI/Voltage Selection ……………………

JP7

RS232/422/485 (COM2) Selection .....................………

JP5

Keyboard/Mouse Connector ..........….....………………

KB_MS1

Reset Connector .........................…....................……….

JP8 (5, 7)

Hard Disk Drive LED Connector .......................……….

JP8 (1, 3)

ATX Power Button ……………………………………..

JP8 (6, 8)

External Speaker Connector ....…........................………

JP8 (14, 16, 18, 20)

PLED Connector …………….…….…...............………

JP8 (2, 4)

KeyLock Connector ……………………………………

JP8 (13, 15)

External SMI Connector ……………..…………..…….

JP8 (17, 19)

Clear CMOS Data Selection ……………………………

JP4

CPU Fan Connector ……………………………………

CPU_FAN1

System Fan Connector ………………………………….

SYS_FAN1

Power Fan Connector …………………………………..

PWR_FAN1

NB Fan Connector ……………………………………..

NB_FAN1

VGA Connector ………………………………………..

VGA1

Serial ATA Connector ………………………………….

SATA1, SATA2, SATA3, SATA4

Floppy Disk Drive Connector ……..........………....…...

FDD1

Printer Connector …….....................……………......…

LPT1

Universal Serial Bus Connector …….....................……

USB1, USB2, USB3

IrDA Connector ………………………………………..

JP1

USB&LAN Connector …....................................………

USB_RJG1, USB_RJG2

ATX Power Connector …………………………………

ATX_PWR1, ATX_PWR2

Sound Connector ………………………….……………

JAUDIO1

CD Audio-In Connector ………………………………..

CD_IN1

Memory Installation ..................................…......………

……………………………………

DIMM1, DIMM2, DIMM3,

DIMM4

Chapter 2 Hardware Configuration

PMB-601LF USER

′

S MANUAL

Page: 2-3

2-2. COMPONENT LOCATIONS

PMB-601LF Connector, Jumper and Component locations

Chapter 2 Hardware Configuration

Page: 2-4

PMB-601LF USER

′

S MANUAL

2-3. HOW TO SET THE JUMPERS

You can configure your board by setting jumpers. Jumper is consists of

two or three metal pins with a plastic base mounted on the card, and by

using a small plastic "cap", Also known as the jumper cap (with a metal

contact inside), you are able to connect the pins. So you can set-up your

hardware configuration by "open" or "close" pins.

The jumper can be combined into sets that called jumper blocks. When

the jumpers are all in the block, you have to put them together to set up

the hardware configuration. The figure below shows how this looks like.

JUMPERS AND CAPS

If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),

You can connect PIN1 & PIN2 to create one setting by shorting. You can

either connect PIN2 & PIN3 to create another setting. The same jumper

diagrams are applied all through this manual. The figure below shows

what the manual diagrams look and what they represent.

Chapter 2 Hardware Configuration

PMB-601LF USER

′

S MANUAL

Page: 2-5

JUMPER DIAGRAMS

2 pin Jumper

looks like this

Jumper Cap

looks like this

3 pin Jumper

looks like this

Jumper Block

looks like this

JUMPER SETTINGS

Looks like this

3 pin Jumper

2-3 pin close(enabled)

Looks like this

Jumper Block

1-2 pin close(enabled)

2 pin Jumper close(enabled)

1

2

12

1

Looks like this

Chapter 2 Hardware Configuration

Page: 2-6

PMB-601LF USER

′

S MANUAL

2-4. COM PORT CONNECTOR

COM1 : COM1 Connector

COM1 is fixed as RS-232.

The pin assignment is as follows :

PIN ASSIGNMENT

1 COM1_DCD#

2 COM1_RX

3 COM1_TX

4 COM1_DTR#

5 GND

6 COM1_DSR#

7 COM1_RTS#

8 COM1_CTS#

9 COM1_RI#

COM2 : COM2 Connector

The COM2 is selectable as RS-232/422/485.

The pin assignment is as follows :

ASSIGNMENT

RS-232 RS-422 RS-485

1 COM2_DCD# TX- TX-

2 COM2_RX TX+ TX+

3 COM2_TX RX+ RX+

4 COM2_DTR# RX- RX-

5 GND GND GND

6 COM2_DSR# RTS- GND

7 COM2_RTS# RTS+ GND

8 COM2_CTS# CTS+ GND

9 COM2_RI# CTS- GND

Chapter 2 Hardware Configuration

PMB-601LF USER

′

S MANUAL

Page: 2-7

COM3 : COM3 Connector

COM3 is fixed as RS-232.

The pin assignment is as follows :

PIN ASSIGNMENT

1 COM3_DCD#

2 COM3_RX

3 COM3_TX

4 COM3_DTR#

5 GND

6 COM3_DSR#

7 COM3_RTS#

8 COM3_CTS#

9 COM3_RI#

COM4 : COM4 Connector

COM4 is fixed as RS-232.

The pin assignment is as follows :

PIN ASSIGNMENT

1 COM4_DCD#

2 COM4_RX

3 COM4_TX

4 COM4_DTR#

5 GND

6 COM4_DSR#

7 COM4_RTS#

8 COM4_CTS#

9 COM4_RI#

Chapter 2 Hardware Configuration

Page: 2-8

PMB-601LF USER

′

S MANUAL

2-5. COM3 RI & VOLTAGE SELECTION

JP6 : COM3 RI & Voltage Selection

The selections are as follows:

SELECTION

JUMPER

SETTINGS

JUMPER

ILLUSTRATION

5V

5-6

12V 3-4

RI 1-2

***Manufacturing Default -- RI.

Chapter 2 Hardware Configuration

PMB-601LF USER

′

S MANUAL

Page: 2-9

2-6. COM4 RI & VOLTAGE SELECTION

JP7 : COM4 RI & Voltage Selection

The selections are as follows:

SELECTION

JUMPER

SETTINGS

JUMPER

ILLUSTRATION

5V 5-6

12V 3-4

RI 1-2

***Manufacturing Default -- RI.

Page is loading ...

Intel PMB-601LF User manual

Intel PMB-601LF User manual

Related papers

Other documents