protech PMB-892LF User manual

USER’S

MANUAL

PMB-892LF

Intel

®

Socket H2 LGA1155

Mini-ITX Motherboard

With VGA/Sound/2LAN(1G)/4COM

P

MB

-

8

9

2

LF

M

1

Copyright Notice

PMB-892LF Intel

®

Socket H2

Mini-ITX Motherboard

With VGA/ Sound/ 2LAN/ 4COM

COPYRIGHT NOTICE

This user’s manual is meant to assist users in installing and setting up the

system. The information contained in this document is subject to change

without any notice.

This manual is copyrighted May 2012. You may not reproduce or transmit in

any form or by any means, electronic, or mechanical, including photocopying

and recording.

ACKNOWLEDGEMENTS

All trademarks and registered trademarks mentioned herein are the property

of their respective owners.

CE NOTICE

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Copyright Notice

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment not

expressly approve by the party responsible for compliance could void your

authority to operate such equipment.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

Installation only by a trained electrician or only by an electrically trained person who

knows all English Installation and Device Specifications which are to be applied.

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual ...................................................... 1-2

1-2 System Specifications .................................................. 1-3

1-3 Safety Precautions ....................................................... 1-6

CHAPTER 2 SYSTEM CONFIGURATION

2-1 Jumper & Connector Quick Reference Table ...............

2-2

2-2 Component Locations ...................................................

2-3

2-3 How to Set the Jumpers ................................................

2-4

2-4 COM Port Connector ……..…………………………..

2-6

2-5 RS232/422/485(COM2) Selection ................................

2-8

2-6 COM2 Auto Detect Selection ……..…………………. 2-9

2-7 CPU Selection ...............................................................

2-9

2-8 Keyboard & Mouse Connector .....................................

2-10

2-9 Reset Connector ............................................................

2-10

2-10 Hard Disk Drive LED Connector ..................................

2-11

2-11 ATX Power Button …...................................................

2-11

2-12 External Speaker Connector ..........................................

2-11

2-13 PLED Connector ……...................................................

2-12

2-14 Clear CMOS Data Selection …………………………. 2-12

2-15 CPU Fan Connector ………..………………………… 2-13

2-16 System Fan Connector ……………………………….. 2-13

2-17 VGA Connector ……………………………………….

2-14

2-18 Serial ATA Connector ……………………………….. 2-15

2-19 Printer Connector ……………………………………..

2-17

2-20 Universal Serial Bus Connector ………………………

2-18

2-21 USB & LAN Connector ………………………………

2-19

2-22 Display Port Connector ……………………………….

2-21

2-23 Digital Input/Output Connector ……………………… 2-21

2-24 ATX Power Connector ………………………………. 2-22

2-25 Sound Connector …………….………………………..

2-23

Contents

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction ................................................................. 3-2

3-2 Intel Chipset Software Installation Utility …..……..... 3-3

3-3 VGA Driver Utility ...................................................... 3-4

3-4 LAN Driver Utility ...................................................... 3-5

3-5 Sound Driver Utility .................................................... 3-6

3-6 Intel

®

ME Driver Utility ................................................

3-7

3-7 USB3.0 Software Installation Utility .............................

3-8

CHAPTER 4 AMI BIOS SETUP

4-1 Introduction ................................................................. 4-2

4-2 Entering Setup ............................................................ 4-4

4-3 Main …….................................................................... 4-6

4-4 Advanced …………………….........................…........ 4-7

4-5 Chipset …………….................................................... 4-30

4-6 Boot ..………………................................................... 4-37

4-7 Security ……………………………………………… 4-40

4-8 Save & Exit ………………………………………….. 4-43

APPENDIX A EXPANSION BUS

Mini-PCIe Bus Pin Assignment ………………………………

A-2

APPENDIX B TECHNICAL SUMMARY

Block Diagram ........................................................................ B-2

Interrupt Map .......................................................................... B-3

DMA Channels Map ……....................................................... B-8

Memory Map ........................................................................... B-9

I/O Map ................................................................................... B-11

Watchdog Timer Configuration …………..…………………. B-15

Flash BIOS Update ………………………………………….. B-17

Page:1-1

INTRODUCTION

This chapter gives you the information for PMB-892LF. It also

outlines the System specification.

Section includes:

 About This Manual

 System Specifications

 Safety Precautions

Experienced users can skip to chapter 2 on page 2-1

for Quick Start.

CHAPTER

1

Chapter 1 Introduction

Page: 1-2

PMB-892LF USER

′

S MANUAL

1-1. ABOUT THIS MANUAL

Thank you for purchasing our Intel

®

3

rd

Gen. Core CPU (Ivy Bridge) Mini-

ITX Motherboard with VGA / Sound / 2LAN / 4COM. PMB-892LF provides

faster processing speed, greater expandability and can handle more task than

before. This manual is designed to assist you how to install and set up the

system. It contains four chapters. The user can apply this manual for

configuration according to the following chapters:

Chapter 1 Introduction

This chapter introduces you to the background of this manual, and the

specifications for this system. The final page of this chapter will indicate

how to avoid damaging this board.

Chapter 2 Hardware Configuration

This chapter outlines the component locations and their functions. In the

end of this chapter, you will learn how to set jumper and how to configure

this card to meet your own needs.

Chapter 3 Software Utilities

This chapter contains helpful information for proper installations of the

VGA utility, LAN utility, and Sound utility.

Chapter 4 AMI BIOS Setup

This chapter indicates you how to set up the BIOS configurations.

Appendix A Expansion Bus

This appendix introduces you the Mini-PCIe expansion bus.

Appendix B Technical Summary

This appendix gives you the information about the Technical maps, Watchdog-

timer configuration, and Flash BIOS Update.

Chapter 1 Introduction

PMB-892LF USER

′

S MANUAL

Page: 1-3

1-2. SYSTEM SPECIFICATION

 CPU

Intel

®

3

rd

Gen. Core CPU (Ivy Bridge) / Socket H2 (LGA1155)

 CHIPSET

Intel

®

Q77 (PCH)

 MEMORY

2×240Pins, Dual channel DDR3-1333/1600MHz up to 16GB





 BIOS:

AMI BIOS (UEFI), with VGA BIOS





 REAL TIME CLOCK:

Build in PCH





 DISPLAY:

Build in processor

Supports VGA, 1 x eDisplay port (Protech Display Port definition)

*

Discrete graphic card is necessary for display if the chosen CPU doesn’t have

integrated graphics support

.





 SERIAL PORT:

4 ports (COM1/3/4 for RS232, COM2 for RS232/422/485)





 PARALLEL PORT:

1 port (Bi-direction, SPP / EPP / ECP)





 USB CONNECTOR:

8 ports

(4x USB3.0 with stack connector on Rear Panel,

4x USB2.0 with box-heater on board.)





 LAN ADAPTER:

Dual ports, support 10/100/1000Mbps

LAN1: Intel

®

82579V (82579LM)

LAN2: Intel

®

82583V

Support Wake-on-LAN.

Chapter 1 Introduction

Page: 1-4

PMB-892LF USER

′

S MANUAL





 SATA INTERFACE:

4 ports of S-ATA connector from PCH

SATA1 & SATA2 -- support SATAIII (6.0Gb/s, with Blue color connector)

SATA3 & SATA4 -- support SATAII (3.0Gb/s)





 KEYBOARD/MOUSE:

1 x PS/2 port (KB/MS)





 BUS SUPPORT:

1 x PCI-e (16X), 1 x MiniPCI-e





 SOUND:

High Definition Audio

Realtek ALC888S

Supports Line-in/Line-out/Mic, audio connector on the rear panel





 SPEAKER:

Internal buzzer





 DIGITAL I/O:

4 in / 4 out





 LED INDICATOR:

1 x HDD LED, 1 x Power LED





 HARDWARE MONITORING FUNCTION:

Voltage, CPU Temperature and Cooling fan speed (CPU, System), Smart Fan

support.





 WATCHDOG:

1~255 Secs.





 RAID FUNCTION:

RAID 0, 1, 5, 10





 POWER SUPPLY:

ATX 24 pin

Chapter 1 Introduction

PMB-892LF USER

′

S MANUAL

Page: 1-5





 TEMPERATURE:

Operation temperature : 0~60°C

Storage temperature :-40~85°C





 HUMIDITY:

Operation humidity : 10~90%

Storage temperature : 5~95%





 BOARD DIMENSIONS:

170mm x 170mm





 BOARD NET WEIGHT:

500 gram





 Certificate:

CE/FCC Class A

Chapter 1 Introduction

Page: 1-6

PMB-892LF USER

′

S MANUAL

1-3. SAFETY PRECAUTIONS

Follow the messages below to avoid your systems from damage:

1. Keep your system away from static electricity on all occasions.

2. Prevent electric shock. Don’t touch any components of this card when the card

is power-on. Always disconnect power when the system is not in use.

3. Disconnect power when you change any hardware devices. For instance, when

you connect a jumper or install any cards, a surge of power may damage the

electronic components or the whole system.

Page 2-1

HARDWARE

CONFIGURATION

** QUICK START **

CHAPTER

2

Helpful information describes the jumper & connector settings, and

component locations.

Section includes:

 Jumper & Connector Quick Reference Table

 Component Locations

 Configuration and Jumper settings

 Connector’s Pin Assignments

Chapter 2 Hardware Configuration

Page: 2-2

PMB-892LF USER

′

S MANUAL

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

CONNECTOR/JUMPER NAME

COM Port Connector COM1, COM2, COM3, COM4

RS232/422/485 (COM2)

Selection

JP8

COM2 Auto Detect Selection JP7

CPU Selection JP9

Keyboard & Mouse Connector

KB_MS1

Reset Connector FP1 (5, 7)

Hard Disk Drive LED

Connector

FP1 (1, 3)

ATX Power Button FP1 (9, 11)

External Speaker Connector FP1 (6, 8, 10, 12)

PLED Connector FP1 (2, 4)

Clear CMOS Data Selection JP2

CPU Fan Connector CPU_FAN1

System Fan Connector SYS_FAN1

VGA Connector VGA1

Serial ATA Connector SATA1, SATA2, SATA3, SATA4

Printer Connector LPT1

Universal Serial Bus Connector

USB45, USB89

USB & LAN Connector LAN1_USB1, LAN2_USB1

Display Port Connector JDP1

Digital Input/ Output Connector

DIO1

ATX Power Connector ATX_PWR1, ATX_PWR2

Sound Connector AUDIO1

Chapter 2 Hardware Configuration

PMB-892LF USER

′

S MANUAL

Page: 2-3

2-2. COMPONENT LOCATIONS

Battery

17

1

7

14

13

26

1

3

2

1

4

3

12

1516

1718

5152

1

9

2

10

1

9

2

10

1 2

10

1

9 10

1 2

7 8

1 2

109

1 1

1

2

11 12

109

1

4

1

6

9

5

10

15

18

14

20

24

21

16

1

6

11

5

10

15

44

42

3532

25

22

51

2

AUDIO1

LAN2_USB1

1

9

2 10

11

12 13 14

LAN1_USB1

1

9

2 10

11

12

13

14

A1

A9

A4

A5

B9

B5

B4

B1

A1

A9

A4

A5

B9

B5

B4

B1

J1

JD09M1

SYS_F

AN1

LPT1 DIO1

SATA1

SATA2

SATA4

17

SATA3

JP4

JP7

JP8

COM2

USB45

USB89

ATX_PWR2

JP9

FP1

SP1

CPU_FAN1

M_PCIE1

JP1

JP2

PCI-E1

KB_MS1

1

JP10

DIMM1

DIMM2

1

2 20

19

JDP1

ATX_PWR1

REMOVE

Intel

LGA1155

Intel

PCH Q77

4

109

12

11

1 13

12 24

PMB-892LF Connector, Jumper and Component locations

Chapter 2 Hardware Configuration

Page: 2-4

PMB-892LF USER

′

S MANUAL

2-3. HOW TO SET THE JUMPERS

You can configure your board by setting jumpers. Jumper is consists of

two or three metal pins with a plastic base mounted on the card, and by

using a small plastic "cap", Also known as the jumper cap (with a metal

contact inside), you are able to connect the pins. So you can set-up your

hardware configuration by "open" or "close" pins.

The jumper can be combined into sets that called jumper blocks. When

the jumpers are all in the block, you have to put them together to set up

the hardware configuration. The figure below shows how this looks like.

JUMPERS AND CAPS

If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),

You can connect PIN1 & PIN2 to create one setting by shorting. You can

either connect PIN2 & PIN3 to create another setting. The same jumper

diagrams are applied all through this manual. The figure below shows

what the manual diagrams look and what they represent.

Chapter 2 Hardware Configuration

PMB-892LF USER

′

S MANUAL

Page: 2-5

JUMPER DIAGRAMS

2 pin Jumper

looks like this

Jumper Cap

looks like this

3 pin Jumper

looks like this

Jumper Block

looks like this

JUMPER SETTINGS

Looks like this

3 pin Jumper

2-3 pin close(enabled)

Looks like this

Jumper Block

1-2 pin close(enabled)

2 pin Jumper close(enabled)

1

2

1 2

1

Looks like this

Chapter 2 Hardware Configuration

Page: 2-6

PMB-892LF USER

′

S MANUAL

2-4. COM PORT CONNECTOR

COM1: COM1 Connector

COM1 is fixed as RS-232.

The pin assignments are as follows:

PIN ASSIGNMENT

1 COM1_DCD#

2 COM1_RX

3 COM1_TX

4 COM1_DTR#

5 GND

6 COM1_DSR#

7 COM1_RTS#

8 COM1_CTS#

9 COM1_RI#

COM2: COM2 Connector

The COM2 is selectable as RS-232/422/485.

The pin assignments are as follows:

ASSIGNMENT

RS-232 RS-422 RS-485

1 COM2_DCD# TX- 485-

2 COM2_DSR# X X

3 COM2_RX TX+ 485+

4 COM2_RTS# X X

5 COM2_TX RX+ X

6 COM2_CTS# X- X

7 COM2_DTR# RX- X

8 COM2_ RI# X X

9 GND GND GND

10 NC NC NC

9

1

10

2

Chapter 2 Hardware Configuration

PMB-892LF USER

′

S MANUAL

Page: 2-7

COM3: COM3 Connector

COM3 is fixed as RS-232.

The pin assignments are as follows:

PIN ASSIGNMENT

1 COM3_DCD#

2 COM3_RX

3 COM3_TX

4 COM3_DTR#

5 GND

6 COM3_DSR#

7 COM3_RTS#

8 COM3_CTS#

9 COM3_RI#

10 NC

COM4: COM4 Connector

COM4 is fixed as RS-232.

The pin assignments are as follows:

PIN ASSIGNMENT

1 COM4_DCD#

2 COM4_RX

3 COM4_TX

4 COM4_DTR#

5 GND

6 COM4_DSR#

7 COM4_RTS#

8 COM4_CTS#

9 COM4_RI#

10 NC

1

5

6

9

COM3

1

5

6

9

COM4

Chapter 2 Hardware Configuration

Page: 2-8

PMB-892LF USER

′

S MANUAL

2-5. RS232/422/485 (COM2) SELECTION

JP8: RS232/422/485 (COM2) Selection

This connector is used to set the COM2 function.

The jumper settings are as follows:

COM 2

FUNCTION

JUMPER

SETTINGS

(PIN CLOSED)

JUMPER

ILLUSTRATIONS

RS232 All Open

RS422

1-2

3-4

9-10

RS485

1-2

5-6

7-8

Note: Manufacturing default – RS232

Chapter 2 Hardware Configuration

PMB-892LF USER

′

S MANUAL

Page: 2-9

2-6. COM2 AUTO DETECT SELECTION

JP7: COM2 Auto Detect selection

The selections are as follows:

SELECTION

JUMPER

SETTINGS

JUMPER ILLUSTRATION

NORMAL 1-2

JP7

AUTO GATING

2-3

JP7

Note: Manufacturing Default – Normal

2-7. CPU SELECTION

JP9: CPU selection

The selections are as follows:

SELECTION

JUMPER

SETTINGS

JUMPER ILLUSTRATION

Ivy Bridge 1-2

JP9

1

Sandy Bridge open

JP9

1

Note: Manufacturing Default – Ivy Bridge

Page is loading ...

protech PMB-892LF User manual

protech PMB-892LF User manual

Related papers

Other documents