Kreg Adaptive Cutting System Project Table Extension Bracket User manual

ADAPTIVE

SYSTEM

01/2019 102399

V1

Owner’s

Manual

Guide d’utilisation / Manual del propietario

EXTENSION BRACKETS ARE COVERED IN THIS MANUAL

EXTENSION BRACKET

(ACS440)

INSTALLATION

(1) Tip up the Extension

Bracket and insert the

tabs into the T-slot in the

Project Table side rail.

(2) Tip the bracket down

until the supports

touch on the bottom

edge of the table rail.

Repeat with the

second bracket.

Kreg

®

Project Table Extension Brackets are intended for use with the

Kreg

®

Adaptive Cutting System Project Table to extend the work surface or

provide workpiece support when used in combination with 2x4 lumber and

the Kreg

®

Mobile Project Center or the Kreg

®

Track Horse.

Side Rail

Support

Install the brackets

INSTALLATION

(3) Adjust the center-to-center bracket spacing to 33" [84cm] to match

the width of the Mobile Project Center or Track Horse.

33" [84cm]

SETUP

(1) Place 2x4s in the

brackets and support

the opposite ends

with the Mobile

Project Center or

Track Horse, using

the brackets included

with these items.

(2) Adjust the height

of the 2x4's to

the desired position

by turning the knob.

(3) Drive 1¼" pocket

screws to secure

the 2x4's.

3

2

1

3

2

1

Using the Extension Brackets

ATTENTION:

!

Refer to your

Mobile Project Center or Track Horse

manual for proper setup.

ATTENTION:

!

Maximum uniformly distributed

load of 350 lbs. [158 kg.] and

maximum span of 7 feet [213cm]

in any conguration.

Surface Flush

SETUP

(4a) Place 2x4s in the brackets and support the opposite ends with the Mobile

Project Center or Track Horse, using the brackets included with these items.

Project Table with Track Horse, extension brackets and support brackets positioned for

workpiece support

4a

Using the Extension Brackets

350lbs. [158 kg.] uniformly distributed

Extension

Bracket

Support

Bracket

7' [213cm]

SETUP

Using the Extension Brackets

(4b) Adjust the Project Table levelers to match the height of the Mobile Project

Center or Track Horse so the table top and extension surfaces are parallel.

4b

Project Table with Track Horse, extension brackets and support brackets positioned for

extended work surface

Project Table with Mobile Project Center, extension brackets and support brackets

positioned for extended work surface

350lbs. [158 kg.] uniformly distributed

Extension

Bracket

Support

Bracket

7' [213cm]

350lbs. [158 kg.] uniformly distributed

Extension

Bracket

Support

Bracket

7' [213cm]

Page is loading ...

TELL US ABOUT

YOUR EXPERIENCE.

YOUR OPINION COUNTS.

We’re always working to improve Kreg

®

products and your satisfaction

with them so that you have great project-building experiences. You can

help by sharing your feedback at www.kregtool.com/feedback. It only

takes a couple of minutes, and will help us to create products and

support that serve your needs better.

CUÉNTENOS SOBRE SU EXPERIENCIA. SU OPINIÓN CUENTA.

Siempre trabajamos para mejorar los productos Kreg

®

y su satisfacción con ellos para que

tenga excelentes experiencias de construcción de proyectos. Puede ayudar compartiendo

su retroalimentación en www.kregtool.com/feedback. Solo toma un par de minutos y nos

estará ayudando a crear productos y brindar un soporte que sirva mejor a sus necesidades.

PARLEZ-NOUS DE VOTRE EXPÉRIENCE. VOTRE OPINION EST

IMPORTANTE POUR NOUS.

Nous cherchons toujours à améliorer les produits Kreg

®

et à nous assurer que vous

soyezsatisfaitlorsquevouslesutilisezpoureectuervosprojetsdeconstructionande

rendre votre expérience agréable. Vous pouvez nous aider en nous faisant part de vos

commentaires au www.kregtool.com/feedback. Cela ne prend que quelques minutes, et vos

commentaires nous aideront à créer des produits et à fournir des services qui répondront

mieux à vos besoins.

For assistance with any Kreg product,

contact us through our Web site or call Customer Service.

Si vous avez besoin d’aide concernant les produits Kreg, communiquez avec nous

sur notre site Web ou appelez notre service à la clientèle.

Si requiere asistencia con cualquier producto Kreg, póngase en contacto

con nosotros a través del sitio web o llame al Servicio al Cliente.

www.kregtool.com • 800.447.8638

201 Campus Dr, Huxley, IA 50124

Kreg Adaptive Cutting System Project Table Extension Bracket User manual

Kreg Adaptive Cutting System Project Table Extension Bracket User manual

in other languages

Related papers

Other documents