2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Robus
  7. RVA7524DU-PSU

Robus RVA7524DU-PSU, RVA5012DU-PSU, RVA5024DU-PSU, RVA7512DU-PSU User manual

  • Hello! I am an AI chatbot trained to assist you with the Robus RVA7524DU-PSU User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1 2
3
4
5
CTRL & AMP
DC+
DC-
V _
V _
V _
V +
CRTL
PSU
W/CH1
C/CH2
V+
DC+
DC-
V+
W/CH1
C/CH2
AMP
PSU
DC+
DC-
V _
V _
V _
V +
CRTL
L
W
N
L
N
L
220-240V
~50HZ
D
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN
FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. If in any
doubt about the installation or use of this product, consult a competent electrician
Note:
Product technical information and specification may change over time without prior
notification. For the latest technical information please visit our web site
www.robus.com.au
Page 1
Installation
The Installation must be carried out by a qualified electrician
-20°C < Ta < +40°C, 220-240V ~ 50Hz, Class II, IP20
Suitable for mounting on a normally flammable surface.
See website for compatible dimmer list: www.robus.com.au
VEGAS 12V/24V, IP20, CONSTANT VOLTAGE DRIVER,
TRIAC DIMMABLE
RVA5012DU-PSU RVA5024DU-PSU
RVA7512DU-PSU RVA7524DU-PSU
50W Max.
50W Max.
75W Max.
75W Max.
3 Years
3 Years
3 Years
≥ 85%
≥ 85%
≥ 85%
12V DC
24V DC
12V DC
≥ 0.9
≥ 0.9
≥ 0.9
4.16A Max.
2.08A Max.
6.25A Max.
3 Years≥ 85%24V DC ≥ 0.93.125A Max.
RVA5012DU-PSU
RVA5024DU-PSU
RVA7512DU-PSU
RVA7524DU-PSU
Output load Output
Current
Output
Voltage PF Efficiency Warranty
RVA5012DU-PSU
RVA5024DU-PSU
RVA7512DU-PSU
RVA7524DU-PSU
L
177mm 58mm 22mm
177mm 58mm 22mm
170mm 56mm 31mm
170mm 56mm 31mm
W D
1 Ensure mains supply is switched off before commencing work.
2 Consider total power of LED strip and choose the appropriate driver code.
Connection options:
A: Connect supply to driver. Brown Live from dimmer to L and Blue Neutral to N
as per figure 2. Connect secondary cable Red V+ and Black V- to positive and
negative on LED strip.
B: In order to increase the length of LED strips, choose the Vegas amplifier.
In order to avoid the over heat, ensure the distance is 50mm allowance between the drivers
in the same installation location.
Dimmer
Issue 1 130718
LED Group Australasia
9/210 Queensport Road North Tel: 07 3890 5444
Murarrie Fax: 07 3890 4777
QLD 4172 Email: [email protected]
Australia Website: www.robus.com.au
LED Group
Crowe Hogwarth Tel: +64 0508 533 335
72 Trafalgar Square Email: [email protected]
NELSON 7010 Website: www.robusled.co.nz
New Zealand
50mm
Please allow 50mm spacing between drivers
/