2. DIODE LED
  3. ATTRIBUTE® Color Controller

DIODE LED ATTRIBUTE® Color Controller Installation guide

  • Hello! I am an AI chatbot trained to assist you with the DIODE LED ATTRIBUTE® Color Controller Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
DRY LOCATION
1 OF 2 IG121115-1.0
ATTRIBUTE
™
INSTALLATION GUIDE
®
COLOR-CHANGING
INSTALLATION GUIDE
ATTRIBUTE™
COLOR CONTROLLER
24VDC
12VDC
1. Install in accordance with naonal and local electrical code
regulaons.
2. This product is intended to be installed and serviced by a qualied,
licensed electrician.
3. DO NOT connect directly to high voltage power. Install with a
compable Class 2 constant voltage LED driver (power supply).
4. Only install compable 12V and 24VDC constant voltage luminaires.
5. This product is rated for indoor installaon and is not protected
against moisture.
6. Do not modify product beyond instrucons or warranty will be void.
SAFETY & WARNINGS
QUICK SPECS / MODELS
TOOLS FOR INSTALL
Phillips-head
screwdriver
SYNCING INSTRUCTIONS
1
Input Operang
Frequency Transming
Distance (RF)
3x AAA 1.5V Baeries
(Not Included)
434MHz /
868 MHz 95 .
2
INSTALL ATTRIBUTE RECEIVER SYSTEM
LED Driver ATTRIBUTE Receiver LED Luminaire
V+
V
L
N
GND
DI-ATT-RGBW-REC
INPUT: 12 - 24VDC
OUTPUT: 12 - 24VDC 4CH X 5A
VV+
W
B
G
R
®
ATTRIBUTE™ Receiver
9/32 in.
(7mm)
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
tc: 167°F
DI-ATT-RGBW-REM SYNC RECEIVER TO ATTRIBUTE CONTROL
DI-ATT-RGBW-REC
INPUT: 12 - 24VDC
OUTPUT: 12 - 24VDC 4CH X 5A
ATTRIBUTE™ Receiver
9/32
in.
(7mm)
OWER
LEARNING KEY
d. Luminaire will ash to indicate pairing.
a. Wake up ATTRIBUTE control by
pressing Power buon.
®
R
B
S1 S2
W
G
®
R
B
S1 S2
W
G
b. Press LEARNING KEY
buon on ATTRIBUTE
receiver.
c. Swipe nger on color wheel.
TURN MAIN POWER OFF BEFORE INSTALLATION.
Refer to WIRING DIAGRAM on next page.
®
R
B
S1 S2
W
G
DI-ATT-RGBW-REC
INPUT: 12 - 24VDC
OUTPUT: 12 - 24VDC 4CH X 5A
VV+
W
B
G
R
®
ATTRIBUTE™ Receiver
9/32 in.
(7mm)
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
tc: 167°F
Add 3x AAA baeries (not included).
Mini at-head
screwdriver
Wire stripper
Input from Driver Output to Load Max Load
12 - 24VDC
Constant Voltage
12 -24VDC
Constant Voltage
4CH x 5A
4CH x 60W (12V)
4CH x 100W (24V)
4CH = 4 Channels
2 OF 2
®Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2015 Elemental LED Inc. All rights reserved. Specicaons are subject to change without noce.
IG121115-1.0ATTRIBUTE
™
INSTALLATION GUIDE
Symptom Common Cause
Remote won’t
funcon
• Check for dead AAA
baeries.
• Remote must be turned
on for operaon (red
indicator light on).
Receiver does
not sync with
remote
• 1) Turn o main power
to receiver and turn back
on. 2) Reset receiver
by holding LEARNING
KEY for 5 seconds unl
LED ashes. 3) Re-sync
receiver to control.
Unpairing the
Receiver
• Hold learning key down
on receiver for 5 seconds
unl LED lights ash. This
will delete the learned ID.
TROUBLESHOOTING
Visit the product web page at www.DiodeLED.com for addional product specicaons & warranty informaon.
ATTRIBUTE COLOR CONTROLLER SPECIFICATION SHEET
For full specicaons.
ADDITIONAL RESOURCES
OPERATION
White Channel
Short press to turn White (CH4) ON/OFF.
Long press to adjust brightness.
Save Color/Scene 2
Long press to save stac color.
Short press to retreive saved color.
Green Channel
Short press to turn Green ON/OFF.
Long press to adjust brightness.
Power
Press to turn Power ON/OFF.
RGB ‘White’ Presets
Short press for 3 types of ‘White’ RGB presets:
warm white neutral white cool white. seul
or applicaons that dont ulie  or 
applicaons.
Dynamic Modes
Short press changes modepauses
mode. Long press adjusts speed of
dnamic mode. See Dnamic ode
hart or mode descripons.
Blue Channel
Short press to turn lue .
Long press to adjust brightness.
Save Color/Scene 1
Long press to save stac color.
Short press to retreive saved color.
Red Channel
Short press to turn Red ON/OFF.
Long press to adjust brightness.
Color Wheel
Adjust  color miing. Power Indicator
Indicator will turn red when power is . Indicator
will ash red when data is transming.
RGB Brightness
ress and hold to adjust 
brightness.
R
B
S1 S2
W
G
Mode Descripon
1Fade 1 - B M R O Y G C
2Fade 2 - B G O W C M B
3Fade 3 - R W C G C W B W
4Skip 1 - R Y W C G W B M W Y
5RGB Fade In/Out
6RGB Fade In
7RGB Fade Out
8RGB Skip
9Fade 4 - B M O G C
10 Fade 5 - W Y W M C W G W M C
11 All Channels O
DYNAMIC MODE CHART
RGB(W) Tape Light / Fixture
*
AC Power
50/60Hz
Class 2 DC Constant
Voltage Driver
AC IN
DC OUT
L
G
N
V
V+
−
RF
TO ATTRIBUTE
CONTROLLER
DI-ATT-RGBW-REC
INPUT: 12 - 24VDC
OUTPUT: 12 - 24VDC 4CH X 5A
V−
V+
W
B
G
R
®
ATTRIBUTE™ Receiver
9/32 in.
(7mm)
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
tc: 167°F
   oonal t cannel
ATTRIBUTE RECEIVER
V+
W
B
G
R
SYSTEM DIAGRAM
HOW TO RESET RECEIVER
If receiver is not operang or pairing correctly with control it may
be necessary to turn power o/on and then reset the receiver. To
reset, hold down the LEARNING KEY buon for 5 seconds unl
LED ashes.
/