SKYDANCE T1 User manual

SKYDANCE
Brand
SKYDANCE
Model
T1
Type
User manual
LVD
User Manual Ver 2.0.4
Technical Parameters
Model No.: T1, T2, T3, T4
Features
Page 1
1-4 color/Glass panel/Touch color wheel/DC input/4 channel constant voltage PWM output/Wireless remote control
Wall Mounted Touch Panel
● Touch panel single color, dual color, RGB or RGBW PWM constant voltage controller.
● Ultra sensitive high strength glass touch panel with touch color wheel in the middle .
● RF 2.4G single zone or multiple zone remote controlCompatibility with .
● Touch keys with LED indicator.
● White & Black glass panel available.
Input and Output
Output type Constant voltage
Output power 144-288W
Output voltage 4 x (12-24)VDC
Output current 4CH,3A/CH
Input voltage 12-24VDC
Input current 12.5A
Light type Single color Dual color RGB
Constant voltage
144-288W
4 x (12-24)VDC
4CH,3A/CH
12-24VDC
12.5A
Constant voltage
144-288W
3 x (12-24)VDC
3CH,4A/CH
12-24VDC
12.5A
Model T1 T2 T3
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~ +55
O
C
T c: +85
O
C
Warranty and Protection
5 years
Protection
Reverse polarity
Over heat
Short circuit
Warranty
T1 T2 T3
T1,T2,T3,T4 Wall Mounted Touch Panel
T4
● T1 Single color panel
● T2 Dual color panel
● T3 RGB panel
Turn on/off light.
Dynamic mode, 6 level speed.
Brightness,10 levels.
Turn off light after 20s.
Brightness wheel.
● T4 RGBW panel
Color wheel.
Adjust dynamic mode speed,10 levels.
Adjust dynamic mode speed or static color brightness,10 levels.
Turn on key tone: Long press power key for 5s when light is off, will turn on or turn off key tone.
Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
4 Scenes, short press recall scene.
Long press 2s to save the current color into 1/2/3/4.
Power
20S
Delay Off
Mode
Bright
SPEED
BRI GHT
MOD E
POW ER
WHI TE
BLU EGRE EN
RED
SCE NE S CEN E S CEN E SCE NE
BRT /SP EEDMOD E
Power
Mode
Bright
20S
Delay Off
Power
Mode
Turn on/off light.
Dynamic mode, 6 level speed.
Turn on/off light.
Brightness,10 levels.
Power
Mode
Bright
SPEED
SCE NE S CEN E S CEN E SCENE
WHITE
BLU EGRE EN
RED
Turn on/off light.
Mode
Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
BRT /SP EED
Color wheel.
Short press get red, green, blue, white color,
long press adjust each color brightness.
RGBW
Constant voltage
144-288W
4 x (12-24)VDC
4CH,3A/CH
12-24VDC
12.5A
T4
Key function
MODE
POWER
BRIGHT
BRIGHT
Brightness +,10 levels.
Brightness -,10 levels.
Color temperature wheel.
+
Weight
0.118kg
Gross weight
Net weight
0.230kg
PWM frequency 2000Hz 2000Hz 1000Hz 1000Hz
Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certification CE,EMC,LVD,RED
EN 62368-1:2020+A11:2020
Safety standard(LVD)
User Manual Ver 2.0.4 Page 2
LED power supply voltage and power select :
● 12V lamp, Input 12V power supply, can load 0~144W,
● 24V lamp, Input 24V power supply, can load 0~288W, The power supply power must larger than load power 20%.
● T2 Dual color panel
● T3 RGB panel
● T1 Single color panel
+
Single color LED strip
+
Single color LED strip
+
Single color LED strip
+
Single color LED strip
● T4 RGBW panel
Power Supply
12-24VDC
Constant Voltage
AC100-240V
Wiring diagram
T1,T2,T3,T4 Wall Mounted Touch Panel
Match Remote Control (two match ways)
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power, repeat again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
The touch panel controller can also match with the RF remote (optional).
End user can choose the suitable match/delete ways. Two options are offered for selection:
Mechanical Structures and Installations
Typical base as below:
European style
Baseplate Base
Uninstall
Installation diagram:
86 size
Touch panel
Use On/Off key
Match:
Turn on light, turn off, immediately press the On/Off
key of the panel for 5s, then press on/off key
(single zone remote) or zone key (multiple zone remote)
of the RF remote within 5s.
The LED indicator fast flash 3 times
means match is successful.
Delete:
Turn on light, turn off, immediately press the On/Off
key of the panel for 10s, delete all matched RF remote.
The LED indicator fast flash 6 times
means all matched remotes were deleted.
RGB/RGBW dynamic mode list (only for T3 / T4)
No. Name No. Name
RGB jump
RGB smooth
6 color jump
6 color smooth
Yellow cyan purple smooth
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
1
2
3
4
5
6
7
8
9
10
86.00 mm
86.00 mm
52.00 mm
52.00 mm
59.00 mm
33.00 mm
11.50 m m
WW1
IN PUT 12 -24V DC
Uin= 12-24 VDC
Uout =4×(12-24)VD C
Iout =4×3A
Pout =4×(36-7 2)W
Temp Ran ge: -30℃~+55℃
T2 Du al Col or LED C ontro ller
0.5-2.0mm²
4-5mm
CW1WW2CW2Ro HS
IN PUT 12 -24V DC
Uin= 12-24 VDC
Uout =3×(12-24)VD C
Iout =3×4A
Pout =3×(48-9 6)W
Temp Ran ge: -30℃~+55℃
T3 R GB LE D Contr oller
0.5-2.0mm²
4-5mm
RoH S
IN PUT 12 -24V DC
Uin= 12-24 VDC
Uout =4×(12-24)VD C
Iout =4×3A
Pout =4×(36-7 2)W
Temp Ran ge: -30℃~+55℃
T4 R GBW L ED Con troll er
0.5-2.0mm²
4-5mm
RoH S
W1W2
W3
W4
IN PUT 12 -24V DC
Uin= 12-24 VDC
Uout =4×(12-24)VDC
Iout =4×3A
Pout =4×(36-7 2)W
Temp Ran ge: -30℃~ +55℃
T1 Di mmer L ED Con troll er
0.5-2.0mm²
4-5mm
RoH S
Power Supply
12-24VDC
Constant Voltage
AC100-240V
Power Supply
12-24VDC
Constant Voltage
AC100-240V
Power Supply
12-24VDC
Constant Voltage
AC100-240V
+
CW
WW Dual color LED strip
+
CW
WW Dual color LED strip
RGB LED strip
RGBW LED strip
W
  • Page 1 1
  • Page 2 2

SKYDANCE T1 User manual

SKYDANCE
Brand
SKYDANCE
Model
T1
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents