soundskins SSK-RAP4DRV2 Operating instructions

Brand: soundskins

Model: SSK-RAP4DRV2

Type: Operating instructions

SoundSkins SSK-RAP4DRV2 is a custom-cut, 4-piece pro kit designed to reduce road noise, vibrations, and rattles in your vehicle's doors. The kit includes everything you need for a professional-grade installation, including sound-dampening material, a roller, a razor blade, and a microfiber cloth. With SoundSkins, you can enjoy a quieter, more comfortable ride in your vehicle.

Truck Door Kit Instructions

1. Start by locating the fastening hardware on the door

panel, take the appropriate screw driver and remove.

2. Once all the screws are removed you can take off the

door panel using a panel tool. Be sure to not break any

of the clips or mounting hardware. Pull panel away slowly

and unplug any electrical connections.

3. Now you are ready to prep the metal surface

using a microfiber cloth, Acetone (use a breathing mask),

and wipe away any moisture, oil, debris or etc. Then let air

dry for an appropriate time. The point is to get the surface

clean to ensure material glue contact.

• Screw driver

• Panel tool

• Microber cloth

• Acetone or cleaning solution

• Razor blade

• Roller

Tools needed for installation:

Soundskins USA

13452 Alondra Blvd, Cerritos, Ca 90703

Phone: 877.211.5597

Email: team@soundskinsglobal.com

www.SoundSkinsGlobal.com

4. When the surface is dry and clean, locate the

piece of the kit with the label on the back that coincides

with the door you’re working on. Make sure it lines up

correctly before you pull the backing off. After you confirm

the right piece, pull off the backing paper and apply the

material at the top and working your way down with a roller.

Make sure the material is pushed down completey and that

no air is trapped. Use a razor blade point or household

needle to release air. Repeat these steps for all door panels.

6. Now you are ready to place the door panel back on your

door. All necessary openings will be available after you

have applied the SoundSkins material. Secure door panel

with all screws and you are now ready to hit the road!

5. Press down firmly onto the area where your car speaker

hole is, and feel for the speaker wire. Use a razor blade to

cut around the speaker hole, being careful to not cut the

wire harness. Take the piece you just cut out and stick it

behind the speaker hole on the outer door skin to act as a

backwave. Score the area where the wire harness is with

your blade and tuck the harness between the two flaps.

Plug in your speaker.

Recommended Installation Instructions

A. Prepping the Surface

After removing interior door panels, you are ready to clean the metal areas that will be insulated. If the metal

has “new” look without imperfections, then take a microfiber cloth and wipe away any dust and

debris. If the metal is showing signs of age like rust, we recommend using Acetone with a breathing mask to

wipe off debris and loose particles. A shop vacuum might be needed to remove loose debris on the floorboard.

B. Installing Panels

Now that you have a clean surface, you are ready to start applying the sheets. We recommend using a roller to release

air pockets that might be lingering from trapped air. You want to make sure that you have rolled those out to the

edge and all the material has a good seal to the metal surface. Make sure all pieces are installed and inspected

before reinstalling the interior.

1) Driver Front Door Panel 3) Passenger Front Door Panel

2) Driver Rear Door Panel 4) Passenger Rear Door Panel

4 Piece Custom Cut PRO KIT

2021+

INSTALLATION VIDEO

Scan code

for “how to”

video!

SKU: SSK-RAP4DRV2

soundskins SSK-RAP4DRV2 Operating instructions

Brand: soundskins

Model: SSK-RAP4DRV2

Type: Operating instructions

Download PDF

report

soundskins SSK-RAP4DRV2 Operating instructions

soundskins SSK-RAP4DRV2 Operating instructions

Related papers

Other documents