MULTIPLEX Walrus Conversion 5028132 Installation guide

Brand: MULTIPLEX

Model: Walrus Conversion 5028132

Type: Installation guide

Instructions

Flomatic 464 A-30 Autofil Valve to Flomatic Walrus Valve Kit

If you have any questions concerning this bulletin, please contact Manitowoc Beverage Equipment’s Technical Service Department at (800) 367-4233

5028132

REV2 04/24/07

NOTE: This kit will not work on valves ordered prior to

1/99. Use the date on the tag to verify the age.

1. Remove the cover from the valve.

2. Turn the syrup and water off to the valve at the back of

the valve with the two white shut-off plugs.

3. Activate the valve to release pressure, and to insure the

water and syrup are turned off to the valve.

4. Remove the electrical plug from the back of the coil.

5. Pull latch pin and remove valve from back block.

6. Remove the green wire between the lever retainer cap and

the green circuit board. Also remove the white wire between

the pin at the diffuser block and the green circuit board.

7. Remove the four screws that hold the solenoid coil in place,

and remove the coil from the valve body. (See Figure 1)

8. Pull the diffuser block off of the flow control base.

(See Figure 2)

9. Remove the two screws that hold the leaf style pallet retainer

spring in place. Then remove the spring. (See Figure 3)

10. Remove the retainer cap from the top of the metal lever.

Then remove the metal lever from the valve. (See Figure 4)

11. Hold the plastic retainer cap with fingers and with pliers pull

the green wire out of the lever retainer cap. (See Figure 5)

12. Locate the new lever supplied in the kit and attach the

lever to the pivot pin using the retainer cap. Route the

wires that are attached to the lever between the two ori-

fice caps. (See Figure 6)

Kit 5031018 Parts and Numbers

Solenoid, Auto Fill, Single .................................. 772-A36

Lever Sensor ....................................................... 516-10

FIGURE 1

FIGURE 2

FIGURE 3

FIGURE 4

FIGURE 5

FIGURE 6

Instructions

Flomatic 464 A-30 Autofil Valve to Flomatic Walrus Valve Kit

If you have any questions concerning this bulletin, please contact Manitowoc Beverage Equipment’s Technical Service Department at (800) 367-4233

5028132

REV2 04/24/07

13. Place the pallet retainer spring back into position on the

valve. Insert the two screws that were removed in step two,

and tighten the screws to secure the retainer plate. Note

the wires attached to the lever should now be under

the pallet retainer spring. Be careful not to pinch the

wires when securing the retainer spring. (See Figure 7)

14. Push the diffuser block over the orifice caps and start the

four screws in each corner of the block. Do not tighten the

four screws completely. (See Figure 8)

15. Place the new solenoid coil over the four screws with the

new plunger inserted into the solenoid. When installing

solenoid place plunger arms on backside of actuators. (See

Figure 9) Once solenoid coil and plunger are in place

tighten the four screws to secure coil assembly.

16. Route the wires that are connected to the new lever to

the left side of the solenoid. (See Figure 10)

17. Plug the connector into the front of the switch housing.

(See Figure 11)

Note: Top-Off or No Top-Off mode must be selected.

A. For Top-Off mode plug the connector into the left and

center pins.

B. For No Top-Off mode plug the connector into the right

and center pins.

18. Replace the valve to the dispenser. Push latch pin down

into position to secure valve to the back block.

19. Connect the 24v wire connector into the valve.

20. Turn the syrup and water shut off valves back on to the valve.

21. Return power to the unit.

22. Activate each retrofitted valve several times to assure

everything is working properly.

FIGURE 7

FIGURE 8

FIGURE 9

FIGURE 10

FIGURE 11

MULTIPLEX Walrus Conversion 5028132 Installation guide

MULTIPLEX Walrus Conversion 5028132 Installation guide

MULTIPLEX Walrus Conversion 5028132 Installation guide

Related papers

Other documents