Unical KUTter B inox User manual

Brand: Unical

Model: KUTter B inox

Type: User manual

This manual is also suitable for

KUTter R inox

ENGLISH

ISTRUZIONI D’USO PER L’UTENTE

USER’S OPERATING INSTRUCTION

ITALIANO

Page is loading ...

SAFETY WARNINGS

CAUTION!

The appliance may only be used by adults after reading the installation and servicing

manual thoroughly.

Children must be supervised to prevent them from playing or tampering with the

appliance

CAUTION!

The appliance must be installed, adjusted and maintained by professionally qualied

personnel, in compliance with the standards and provisions in force. Incorrect instal-

lation can cause damage to persons, animals and objects for which the manufacturer

cannot be held responsible.

DANGER!

NEVER attempt performing maintenance or repairs on the appliance on your own

initiative.

Any work must be done by professionally qualied personnel. We recommend stip-

ulating a maintenance contract.

Insufcient or irregular maintenance can jeopardise the operating safety of the appli-

ance and cause damage to persons, animals and objects for which the manufacturer

cannot be held responsible.

ATTENTION!

Changes to the parts connected to the boiler (once the boiler installation is complete)

Do not modify the following parts:

- the boiler

- the gas, air, water and electricity supply lines

- the ue gas pipe, the safety valve and the exhaust pipe

- the construction parts which affect the operating safety of the appliance.

ATTENTION!

To tighten or loosen the screwed ttings, use only appropriate xed spanners.

Non-compliant use and/or inappropriate tools can cause damage (e.g. water or gas

leakage).

ATTENTION!

Indications for propane gas-red appliances

Make sure that the gas tank has been deaerated before installing the appliance.

For state-of-the-art tank venting, contact the LPG supplier or person qualied in

compliance with the law requirement.

If the tank has not been professionally deaerated, ignition problems could arise.

In that case, contact the supplier of the LPG tank.

DANGER! Smell of gas

Should a smell of gas be perceived, follow these safety guidelines:

- do not turn electric switches on or off

- do not smoke

- do not use the telephone

- close the gas shut-off valve

- air out the area where the gas leakage has occurred

- inform the gas supplier or a company specialised in installation and maintenance

of heating systems.

DANGER! Explosive and easily ammable substances

Do not use or store explosive or easily ammable materials (e.g. petrol, paints, paper)

in the room where the appliance is installed.

DANGER!

Do not use the appliance as a supporting base for objects.

In particular, do not place receptacles containing liquids (Bottles, Glasses, Jars or

Detergents) on top of the appliance.

If the appliance is installed inside a housing, do not insert or rest other objects inside

this housing.

ENGLISH

1 - SYMBOLS USED IN THE MANUAL

NOTE!

Tips

for the user

ATTENTION!

Possible dangerous

situation for the product and the environment

DANGER!

Serious danger for

personal safety and life

2 - APPROPRIATE USE OF APPLIANCE

The boiler has been built according to the current level of engineering and acknowledged

technical safety rules.

Nonetheless, if improperly used, dangers could arise for the safety and life of the user and

other persons or damage to the equipment or other objects.

The appliance is designed to work in heating systems, with hot water circulation, for the pro-

duction of domestic hot water.

Any other use is considered improper.

UNICAL AG S.p.A. will not be held liable for any damage resulting from improper use.

Use according to the intended purposes also includes strict compliance with the instructions

in this manual.

The user must be instructed concerning the use and operation of the heating system, in particular:

• Delivertheseinstructionstotheuser,aswellasotherdocumentsconcerningtheappliance

inserted in the envelope inside the packaging. The user must keep this documentation safe

for future consultation.

• Informtheuserabouttheimportanceoftheairventsandtheuegasexhaustsystem,high-

lighting their essential features and the absolute prohibition of modifying them.

• Informtheuserconcerningcontrollingthesystem'swaterpressureaswellasoperationsto

restore it.

• Informtheuserconcerningcorrecttemperaturecontrol,controlunits/thermostatsandradiators

for saving energy.

• Rememberthatthesystemmustreceiveregularmaintenanceatleastonceayearandcom-

bustion analysis must be performed every two years (as per national law).

• Shouldtheappliancebesoldortransferredtoanewownerorifyoumoveandleavethe

appliance, always make sure that the instruction booklet accompanies it in order to be con-

sultedbythenewownerand/orinstaller.

The manufacturer will not be held liable in the event of damage to persons, animals or objects

resulting from failure to comply with the instructions contained in this manual.

4 - INFORMATION PROVIDED TO THE USER

BY THE INSTALLATION/MAINTENANCE TECHNICIAN

3 - WATER TREATMENT

• Thehardnessofthefeedwaterconditionsthefrequencyatwhichthedomestichotwater

exchangermustbecleaned.

• Ifthewaterhasahardnessgreaterthan15°f,werecommendusingwatersofteners,chosen

according to the characteristics of the water.

• Inordertoimprovescalingresistance,itisrecommendedtoadjustthedomestichotwaterat

a temperature very close to that actually used.

• Itisrecommendedtoverifythecleanlinessofthedomestichotwaterexchangerattheend

oftherstyear,andthenaccordingtothelevelofscalingfound;theperiodcanbeextended

to two years.

Pay special attention when reading this manual to the parts marked by the symbols:

C - Domestic hot water temperature

regulator

Via this knob it is possible to ad-

just the domestic hot water inlet

temperature:

(with STORAGE WATER TANK)

Positioning the knob in the eld

indicated at the side, adjusts the

DHWtemperature.

The adjustment is between min.

25°Candmax60°C.

The knob positioned in the first

part, indicates that preparation of

the storage water tank is disabled,

it remains active frost protection

water storage tank.

(CH+DHW)

Positioning the knob in the eld

indicated at the side, adjusts the

DHWtemperature.

The adjustment is between min.

38°Candmax60°C.

The adjustment refers to the request from

the ON-OFF thermostat.

The temperature requested through the

OT input (Open therm) must be set on

the Regola Facile (maximum heating

ROOMTHERMOSTATS:

temperature) and it is independent from the position

oftheknob,exceptfor“Winter”modeenabling.

5 - OPERATING INSTRUCTIONS

5.1 - CONTROL PANEL

B - Summer / Winter Selector +

Heating temperature regulator

Via this knob it is possible to se-

lect the operating mode:

Summer (domestic hot water pro-

duction only)

The knob in position

(Summer)

indicatesthatheatingisexcluded

and that the antifreeze function

stays active.

Winter (domestic hot water pro-

duction and heating temperature

adjustment).

Positioning the knob in the eld

shown to the side, indicates that

theboilerisin“Winter”mode,and

adjusts the temperature of the

heating circuit water.

The adjustment is between min.

30°Candmax85°C.

KEY

A Pressure gauge

B Summer/WinterSelector+Room

heating temperature regulator

(request from ON-OFF thermostat)

C Domestichotwatertemperatureregulator

D Unblock/calibration/diagnosisbutton

E Information display

F Heatingfunctionactive

G Domestichotwaterfunctionactive

I Block symbol

L Burner in operation symbol

M Fault symbol

N Temperatureoffaultcodeindicationorindex

parameter

ENGLISH

L - Burner in operation signal

This symbol indicates that the burn-

er is in operation.

The symbol lights up when the boil-

er receives a request for heating or

domestic hot water production.

F - Operation in heating mode

The symbol lights up when the

boiler receives a request in heating

mode. If a request for domestic hot

water production is received at the

same time, the light switches off.

G - Operation in hot water

production mode

This symbol lights up when there

is a request for domestic hot water.

I - Block signal

The symbol lights up when the

burner safety device has inter-

vened, due to:

- No gas

- Failed ignition

Intherstcase,inwhichtheburner

will not light, one must check if the

gas valve is open.

M - Fault signal

The symbol lights up on the display

monitor when the boiler detects an

operation anomaly or it is blocked

due to a permanent fault. The code

thatidentiesthecauseisdisplayed

in place of the degrees centigrade

bypressingtheunblockbutton(D).

The symbol is also displayed by en-

abling the calibration function and

asheswhenchangingparameters.

D - Unblock button

Byactingonthisbuttonfor<1sec.

one can:

- restart the boiler after the burner

safety device has intervened, ac-

tivating the symbol on the display

- display the error code when the

boiler operation is block due to

a permanent fault, activating the

symbol on the display

Thermometer

If, on the display, the symbol

( ) is lit up, the temperature in-

dicated is that relating to the water

for the heating circuit

If, on the display, the symbol

(

) is lit up, the temperature in-

dicated is that relating to the water

for the domestic hot water circuit.

A - Pressure gauge

Displaysthewaterpressureinside

the heating circuit; this pressure

valuemustnotbebelow0.8/1bar

(when cold).

If the pressure dropsbelow 0.8/1

bar, one must restore the correct

valuebyactingonthesystemll-

ing valve. This operation must be

carried out when the boiler is cold.

6.2 - CHECKS BEFORE COMMISSIONING

1 Makesurethegasshut-offvalveupstreamof

the boiler is open.

2 Check that any shut-off valves

formaintenance,ontheowand

return are open.

3 Check that the shut-off valve, for maintenance,

on the domestic cold water inlet is open.

4 Check that the safety valves outlet has been

connected to the drains.

5 Checkthattheboilerispoweredelectrically;

thedisplay(E)onthecontrolpanelmustbe

lit up.

6 Check the water pressure on the boiler pres-

sure gauge (A); for optimum operation, the

pressure should be between 0.8 and 1 bar

(with pump stopped).

Shouldthepressurebelowerthan0.7barwith

the system cold, restore pressure by opening

thesystemllingtap(seepar.6.4).

Antifreeze protection

The boiler is equipped with an antifreeze protection system.

To activate the antifreeze function, position the

two knobs as shown in the gure.

The antifreeze protection inter-

venes only if the boiler is powered

electrically and if the gas valve is

open.

If for some reason there is a power

or gas failure, the antifreeze protec-

tion described above is not active.

The frost protection is enabled on

both circuit:

CHHeatingand

DHWwatertank.

5.3 - OPERATION

Domestic hot water production

(Summer Mode)

Makesurethattheselector(B) is

positioned on ( )

(with STORAGE WATER TANK)

Position the domestic hot water

temperature knob (C) on the de-

sired temperature.

- completely to the left = 25°C

- completely to the right = 60°C

(CH+DHW)

Posizionare la manopola (C) di

regolazione della temperatura sani-

tario, sulla temperatura desiderata.

-IncorrispondenzadiMIN

la temperatura e’ minima = 38°C

- completamente a destra = 60°C

Regolandolatemperaturadell’acquacaldasani-

taria ad una temperatura molto vicina a quella di

utilizzo, eviterete di miscelare acqua calda con

acqua fredda, realizzando economie di gestione e

riduzione sensibile di formazioni calcaree.

Aprendo un rubinetto dell’acqua

calda, l’apparecchio si aziona au-

tomaticamente ed eroga acqua alla

temperatura impostata.

Durantetuttalafasediprelievosul

display viene visualizzata la tempe-

ratura dell’acqua calda sanitaria e

il simbolo (

) rimane illuminato.

with STORAGE

WATER TANK

(CH+DHW)

Heating

discharge

For operation in heating mode the

knob (B) must be positioned in the

eldshowninthegure,

-IncorrespondenceofMIN

the temperature is minimum = 30°C.

- completely to the right = 85°C

If the heating system is equipped

with a modulating room thermostat

(TA mod REGOLAFACILE/OPEN

THERM),CH temperaturewillbe

adjusterd automatically by thermo-

stat TA mod.

Theknobcontrolsonlythemaxi-

mum temperature of the request

from the thermostat ON-OFF and

enablestheCHifknobisinposition

higherthe“MIN”position.

Duringtheheatingstage,thedis-

play shows the water temperature

and the symbol (

) stays lit up

Complete decommissioning

To decommission the system,

disconnect the boiler from the

power supply by acting on the main

switch.

In the event of complete decom-

missioning, the heating and hot

water production modes as well

as the antifreeze protection are

completely disabled.

If idle for long periods, close the

gas shut-off valve and cold water

cock, if present

ENGLISH

Whentheboilerdetectsanoperationanomalyor

it is blocked due to a permanent fault, the control

panel display lights up, and the symbol (

service

) starts

toash.

If the fault is permanent, the error code is displayed

in place of the degrees centigrade.

For the codes listed on this page,

it is not necessary to press button

“D” to display the error code.

bypressingtheunblockbutton“D”

thecodethatidentiesthecauseis

displayed,ashing,inplaceofthe

degrees centigrade,

(forthe“errorcodes”listseepar.

4.6 installation and maintenance

instruction manual).

The user can intervene to restore proper operation

only in the following cases:

System pressure too

low

How to elimi-

nate the fault:

Restorethecorrectpressurevalue

byactingontheboilerllingvalve

(for optimum operation, the pres-

sure value should be within 0.8

and1bar).

Whentheminimumpressurevalue

isreached(0.6bar),boileropera-

tion is resumed.

If water pressure must be con-

tinually restored, contact an

Authorised Assistance Centre.

Burner ignition block

Burner blocking device triggered

due to:

- no gas

- air in pipe (when system is new

or after long idle period).

How to

eliminate the

fault:

Check that the gas valve is open

and press the unblock button to

resume the proper operation of

the boiler.

After 3 interventions of the boiler

blocking device, do not try to re-

sume operation of the boiler by

yourself. Contact an Authorised

Assistance Centre.

Safety thermostat intervention

(due to air)

How to elim-

inate the

fault:

Bleed the air from the radiators and

restore system pressure.

For all the other error codes, the user is NOT

authorised to resume boiler operation by him-

self. Contact an Authorised Assistance Centre.

The constructor disclaims any liability for damage

caused as a result of improper installation, use,

appliance conversion or for non-compliance with

the instructions supplied by the manufacturer or

installation regulations in force concerning the

material in question.

Provisions for proper disposal of the product in accordance with Directive 2002/96/EC

At the end of its life cycle the product must not be disposed of as urban waste. It can be taken to

a special recycling centre managed by the local authorities, or to a dealer who offers this service.

Separate disposal of a domestic appliance avoids possible negative consequences for the environment

and human health deriving from inappropriate waste handling and allows the recovery of the materials

ofwhichitismade,inordertoobtainsignicantenergyandresourcesavings.

5.4 - ELIMINATING FAULTS

Page is loading ...

00335775 -1

edizione01/16

www.unical.eu

Unicaldeclinaogniresponsabilitàperlepossibiliinesattezzesedovuteaderroriditrascrizioneodistampa.Siriservaaltresìildirittodi

apportareaipropriprodottiquellemodichecheriterrànecessarieoutili,senzapregiudicarnelecaratteristicheessenziali.

46033 casteldario - mantova - italia - tel. +39 0376 57001 - fax +39 0376 660556

[email protected] - [email protected] - www.unical.eu

AG S.p.A.

Unicaldeclineseveryresponsibilityforthepossibleinaccuraciesifowedtoerrorsoftranscriptorpress.Alsoreservestherighttobringthose

changesthatitwillholdnecessarytoitownproductsorprots,withoutjeopardizingitsessentialcharacteristics.

Unical KUTter B inox User manual

Brand: Unical

Model: KUTter B inox

Type: User manual

This manual is also suitable for

KUTter R inox

Download PDF

report

in other languages

italiano: Unical KUTter B inox Manuale utente

Unical KUTter B inox User manual

This manual is also suitable for

Unical KUTter B inox User manual

in other languages

Related papers

Other documents