Skov BinTrac feature software Technical User Guide

Brand: Skov

Model: BinTrac feature software

Type: Technical User Guide

BinTrac

Feature Software

Technical User Guide

604415 • 2023-05-31 Software version 8.0

BinTrac

Technical User Guide 3

Product and Documentation Changes

SKOV A/S reserves the right to change this document and the product herein described without further notice.

In case of doubt, please contact SKOV A/S.

The date of change appears from the front and back pages.

Note

• All rights belong to SKOV A/S. No part of this manual may be reproduced in any manner whatsoever without

the expressed written permission of SKOV A/S in each case.

• All reasonable efforts have been made to ensure the accuracy of the information contained in this manual.

Should any mistakes or imprecise information occur in spite of this, SKOV A/S would appreciate being noti-

fied thereof.

• Irrespective of the above, SKOV A/S shall not accept any liability with regard to loss or damage caused or

alleged to be caused by reliance on any information contained herein.

• Copyright by SKOV A/S.

BinTrac

Technical User Guide

1 Guidelines ....................................................................................................................................................... 5

2 Product description ....................................................................................................................................... 6

3 Product survey ............................................................................................................................................... 7

4 Maintenance guide ......................................................................................................................................... 8

5 Installation guide............................................................................................................................................ 9

5.1 Feature software ........................................................................................................................ 9

5.1.1 Backup of settings........................................................................................................................ 9

5.2 Loading software ..................................................................................................................... 10

5.3 Setting up BinTrac in the controller....................................................................................... 11

5.4 Cable plan................................................................................................................................. 12

5.5 Circuit diagram......................................................................................................................... 12

6 Testing........................................................................................................................................................... 13

7 Technical data USB...................................................................................................................................... 14

BinTrac

Technical User Guide 5

1 Guidelines

This manual describes the specific feature software functionality. For a general description of the controller’s op-

eration and other functions, see the controller user and technical manual.

BinTrac

6 Technical User Guide

2 Product description

BinTrac feature software is a software feature to be used when BinTrac silo weighing is to be used with the

SKOV controller.

BinTrac is provided as a software feature for post-installation in running controllers with production system soft-

ware.

For further information about installation of the BinTrac system, please refer to the products own documentation.

For further information about the production controller, please refer to its own documentation.

BinTrac Indicator BinTrac

HouseLINK

CAN-bus module Production

controller

BinTrac

Technical User Guide 7

3 Product survey

Feature Software

136799 BlueControl BinTrac, feature SW

BinTrac is a feature for after-installation in a controller with production sys-

tem software. When loading the feature software, new functions are added

to the menus of the controller.

Feature software can be installed in controllers with version 7.3 software or

higher. If the controller software version is older than version 7.3, it requires

update to the latest version before installing the feature software.

It is supplied with English documentation.

132245 CAN-bus module

Always use the CAN-bus module when using external CAN bus communi-

cation.

One for each controller.

130121 CAN bus cable 50 m

130125 CAN bus cable 100 m

130126 CAN bus cable 250 m

For indoor use.

Must be used with external units using CAN bus communication.

130123 CAN bus cable UV 50 m

130127 CAN bus cable UV 100 m

130128 CAN bus cable UV 250 m

For outdoor use.

Must be used with external units using CAN bus communication.

BinTrac

8 Technical User Guide

4 Maintenance guide

There is no maintenance of software.

The functions from a feature software are not overwritten by a subsequent software update, but are updated to-

gether with the latest update.

It is not possible to uninstall feature software once it is installed.

BinTrac

Technical User Guide 9

5 Installation guide

5.1 Feature software

The Feature Software is provided on a USB stick.

Important information

Feature software can only be installed on house controllers with software version 7.3 or later.

The controller restarts after loading the feature software so it is not advisable to carry out the up-

load when there are animals in the livestock house.

If it is necessary to load the software while animals are in the house, it should be carried out in the

presence of a veterinary expert.

Working procedure when installing Feature Software

1. Create a backup copy of the controller settings.

2. Load feature software and wait for the house controller to restart.

3. Activate the function.

4. Set up the function in the house controller.

5. Make the settings.

5.1.1 Backup of settings

Save the controller settings and pages before loading the software.

Menu button | Settings | Service | SD card | Save

Confirm and wait until the controller indicates that the settings are saved.

BinTrac

10 Technical User Guide

5.2 Loading software

1. Loosen the screws (A) that hold the front panel in place.

2. Lift out the front panel. Make sure not to pull the flat cable so that the plug (B) is damaged.

Figure1: Loading software

3. Unpack the USB stick (C) and label (D) from the box.

4. Place the small accompanying label at the side of the CPU module (E).

5. Insert the USB stick containing the software in the USB port (F) on the CPU module.

Menu button | Settings | Service | Install software

Select the required software.

Installation begins.

Settings are automatically saved before the installation starts

and are loaded after the restart.

The controller restarts during installation.

It is VERY important not to disconnect the power supply during installation.

Do not remove the USB memory stick until the installation is fully completed. In other words, when

the graphical user interface is accessible and usable.

BinTrac

Technical User Guide 11

5.3 Setting up BinTrac in the controller

Make sure the CAN protocol is set to CANopen.

| Technical | Installation | Manual installation | CAN

protocol

Select the Silo Weighing box (BinTrac), for each BinTrac the

number of silos must be selected. The software supports up to

8 electronic silo weighers.

| Technical | Installation | Manual installation | Silo

weighing boxes

Here you see the CAN-bus address (CAN ID) and if it is con-

nected.

The controller’s installation menu specifies to which silo weigh-

ing module and in which silo weighing box the silo load cells are

connected.

For correct connection of silo load cells, see menu |

Technical | Installation | Show connection

BinTrac

12 Technical User Guide

5.4 Cable plan

CAN bus cable

max. 400m

Supply

BinTrac

House Link

(B) (A)

(A) Power supply to the controller two-wire cable including earthing contact.

(B) Max. 400 m CAN bus cable between the silo weighing box and the controller.

5.5 Circuit diagram

BinTrac

Technical User Guide 13

6 Testing

After loading the software you must make a thorough test to ensure that the system works as intended.See also

the Technical Manual for the house controller.

BinTrac

14 Technical User Guide

7 Technical data USB

Network

USB USB 2.0 A type

Variant

Controllers BlueControl fjerkræ

Software version 7.3 or later

Environment

Operating temperature °C (°F) -40 to +40 (-40 to +104)

Temperature, storage °C (°F) -40 to +70 (-40 to +148) – and protected against direct sunlight.

Shipment

Dimensions when packed

HxWxD

mm 340x265x30

Shipping weight g210

604415 • 2023-05-31 • en-US • Made in Denmark

SKOV A/S • Hedelund 4 • Glyngøre • DK-7870 Roslev

Tel. +45 72 17 55 55 • www.skov.com • E-mail: [email protected]

Skov BinTrac feature software Technical User Guide

Skov BinTrac feature software Technical User Guide

Skov BinTrac feature software Technical User Guide

Related papers

Other documents