Valco baby Car Seat Adapter Operating instructions

Brand: Valco baby

Model: Car Seat Adapter

Category: Strollers

Type: Operating instructions

Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this

guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all

the warnings and safety guidelines before use. This product is for use with the VALCO Latitude stroller in North

American only. This product is not intended for use in Australia.

Important: Please read the following instructions carefully before assembling this product. Retain this

guide in a safe place for future reference.

PRODUCT REFERENCE GUIDE

Due to our policy of continuous

product development, this

product is constantly evolving. It

is possible that some features or

procedures outlined here have

changed since this document

was written. If you are unsure

of any procedure shown here,

please contact us via the web at

info@valcobaby.com to obtain

the most up to date information

before use. Include the batch

number, which can be found on a

sticker on the frame.

All pictures and diagrams herein

are provided for illustration

purposes only. Actual product,

colour or fabric may vary. VALCO

reserves the right to modify or

alter any specication or colour

without notice or obligation to

modify any product previously

purchased

FURTHER INFORMATION

North America only

www.valcobaby.com

1800 610 7850

Twin Latitude Car

Seat Adapter

Compatible with most Graco/Britax Car Seats

INSTALLING YOUR TWIN GRACO

OR BRITAX CAR SEAT ADAPTOR

FIGURE A

1. Begin preparing the Latitude stroller for

the Car Seat Adaptor by removing the canopy

(hoods) from the stroller and reclining the

seats to their fully reclined position (detailed

instructions in the Twin Latitude Stroller

Instruction Manual).

FIGURE B

2. Remove the extra hood and the Male and

Female straps from the packaging and dispose

of packaging responsibly.

FIGURE C

3. The extra hood is intended to shade the seat

of the stroller being used without a car seat.

4. Prepare the Hood for installation by rotating

the hood rods so they are aligned with the

corresponding connector pieces on the stroller

frame (where the twin hood was connected.) (1)

5. Simultaneously slide the hood rods onto

the corresponding raised pieces of the stroller

frame and lock into place. (2)

6. Snap the hood snaps onto the corresponding

snap pieces on the stroller seat back.

FIGURE D

6. The Male and Female straps are intended to

secure the car seat to stroller frame.

7. Select a strap to secure around the side bar

of the Latitude stroller.

NOTE: ONLY SECURE THE STRAP TO THE SIDE

OF THE STROLLER WITHOUT THE HOOD.

Female Buckle

Male Buckle

Seat Reclined

Hood

Bumper Bar

Select a strap to secure to stroller

FIGURE E

7. Fit the strap around the side bar of the

Latitude stroller.

FIGURE F

8. Slip the strap through the ‘opening’ of the

metal loop at the end of the strap.

FIGURE G

9. Once strap is through the metal loop, pull

plastic end up to tighten, and secure on stroller.

10. Repeat the process outlined in Figures D to

G to attach the remaining strap to the middle

bar of the stroller.

FIGURE H

11. Place car seat in seat portion of the stroller.

12. Be sure your car seat is securely tted over

the front bumper bar, and in the stroller seat.

TIP: YOU MAY WANT TO ADJUST THE FRONT

BUMPER BAR AND SEAT RECLINE FOR A MOST

SECURE FIT.

Pull up to tighten

Secure on stroller

Wrap the strap around side bar

IMPORTANT WARNING: ALWAYS TEST THAT ALL

STRAPS ARE SECURELY ENGAGED BEFORE USE.

In North America only

www.valcobaby.com

1 800 610 7850

FIGURE I

13. Locate a Male/Female strap attached to

side of stroller.

14. Slip strap through the car seat belt hooks

on the side of the car seat.

15. Repeat with the other strap.

16. Insert Male clip into its Female counterpart

and buckle.

17. Adjust straps to tighten around car seat.

TO REMOVE YOUR CAR SEAT:

18. Reverse the steps outlined in Figure I and

lift out the car seat.

WARNINGS

•Always follow car seat manufacturer’s instructions when using the car seat.

•Be sure to check that all straps are securely xed and in place before use.

• Check all parts for breakage or fatigue before use. Discontinue immediately if any part

is found to be damaged or broken.

• NEVER leave any child unattended at any time.

• This product is intended for use in North America only. It is not intended for use in

Australia.

• This product is intended for domestic use only. It is not intended for commercial use.

Valco baby Car Seat Adapter Operating instructions

Brand: Valco baby

Model: Car Seat Adapter

Category: Strollers

Type: Operating instructions

Download PDF

report

Valco baby Car Seat Adapter Operating instructions

Valco baby Car Seat Adapter Operating instructions

Related papers

Other documents