ELICA EVL436S1 Install Instructions Volterra

Page is loading ...

2

English

Français

Español

Contents

Sommaire

Contenido

page

página

2

15

27

English

Contents

Important safety notice........................................................................................................................................ 3

Electrical & installation requirements ...............................................................................................................

4

Electrical requirements ................................................................................................................................................................................. 4

Before installing the hood .............................................................................................................................................................................

4

List of materials.................................................................................................................................................... 5

Parts supplied ............................................................................................................................................................................................... 5

Parts not supplied ......................................................................................................................................................................................... 5

Dimensions and clearances............................................................................................................................... 5

Duct options and examples................................................................................................................................ 6

Installing preparation...........................................................................................................................................

6

Mounting the duct cover bracket.................................................................................................................................................................... 7

Ceiling / wall ducting .....................................................................................................................................................................................

7

Installation ............................................................................................................................................................8

Mounting the hood ........................................................................................................................................................................................ 8

Electrical connection................................................................................................................................................................................... 9

Description of the hood & controls................................................................................................................... 10

Controls.......................................................................................................................................................................................................... 10

Maintenance ......................................................................................................................................................... 11

Available accesories............................................................................................................................................ 12

Warranty ............................................................................................................................................................... 13

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Safety Warning: Turn off power circuit at service panel and lock out panel, before wiring this appliance.

Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit

3

READ AND SAVE THESE INSTRUCTIONS

Important safety Notice

CAUTION

FOR GENERAL VENTILATING USE ONLY. DO NOT USE

TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS OR VAPOURS.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

Before servicing or cleaning the unit, switch power off

at service panel and lock service panel disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Installation Work and Electrical Wiring Must Be Done By

 QualiedPerson(s)InAccordanceWithAllApplicable

Codes & Standards, Including Fire-rated Construction.

Sufcientairisneededforpropercombustionand 

 exhaustingofgasesthroughtheue(Chimney)offuel

burning equipment to prevent back- drafting.

Follow the heating equipment manufacturers guideline

and safety standards such as those published by the

 NationalFireProtectionAssociation(NFPA), 

 theAmericanSocietyforHeating,  

 RefrigerationandAirConditioningEngineers(ASHRAE),

and the local code authorities.

When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

Ducted systems must always be vented to the outdoors.

CAUTION

To reduce risk of re and to properly exhaust air, be

sure to duct air outside - do not vent exhaust air into

spaces within walls, ceilings, attics, crawl spaces, or

garages.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL

DUCT WORK.

Install this hood in accordance with all requirements

specied.

WARNING

To Reduce The Risk Of Fire Or Electric Shock, Do Not

Use This Hood With Any External Solid State Speed

Control Device.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.

Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

 ignite.Heatoilsslowlyonlowormediumsettings.

AlwaysturnhoodONwhencookingathighheator 

 whenambeingfood(I.e.CrepesSuzette,Cherries 

 Jubilee,PeppercornBeefFlambe’).

Clean ventilating fans frequently. Grease should not be

 allowedtoaccumulateonfanorlter.

Useproperpansize.Alwaysusecookwareappropriate

 forthesizeofthesurfaceelement.

A.

B.

C.

D.

E.

F.

a)

b)

c)

d)

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN

THE EVENT OF A RANGE TOP GREASE FIRE,

OBSERVE THE FOLLOWING:

a

SMOTHERFLAMESwithaclose-ttinglid,cookie 

sheet, or other metal tray, then turn off the gas burner or

 theelectricelement.BECAREFULTOPREVENT 

 BURNS.Iftheamesdonotgooutimmediately, 

 EVACUATEANDCALLTHEFIREDEPARTMENT.

NEVERPICKUPAFLAMINGPAN-youmaybe 

burned.

DONOTUSEWATER,includingwetdishclothsor 

towels - a violent steam explosion will result.

Use an extinguisher ONLY if:

YouknowyouhaveaclassABCextinguisher,and

you already know how to operate it.

Thereissmallandcontainedintheareawhereit

started.

Theredepartmentisbeingcalled.

Youcanghttherewithyourbacktoanexit.

a

Basedon“KitchenFireSafetyTips”publishedbyNFPA.

OPERATION

a.Alwaysleavesafetygrillsandltersinplace.Without

these components, operating blowers could catch onto hair,

ngersandlooseclothing.

Themanufacturerdeclinesallresponsibilityintheeventof

failure to observe the instructions given here for installation,

maintenanceandsuitableuseoftheproduct.The

manufacturer further declines all responsibility for injury due

to negligence and the warranty of the unit automatically

expires due to improper maintenance.

a)

b)

c)

d)

1)

2)

3)

4)

4

Electrical & Installation requirements

Electrical requirements

IMPORTANT

Observeallgoverningcodesandordinances.

It is the customer’s responsibility:

Tocontactaqualiedelectricalinstaller.

Toassurethattheelectricalinstallationisadequateandin

conformancewithNationalElectricalCode,ANSI/NFPA70

—latestedition*,orCSAStandardsC22.1-94,Canadian

Electrical Code, Part 1 and C22.2 No.0-M91 - latest

edition** and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommendedthataqualiedelectriciandeterminethatthe

ground path is adequate.

Do not ground to a gas pipe.

Checkwithaqualiedelectricianifyouarenotsurerange

hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

IMPORTANT

Save Installation Instructions for electrical inspector’s use.

Therangehoodmustbeconnectedwithcopperwireonly.

Therangehoodshouldbeconnecteddirectlytothefused

disconnect(Orcircuitbreaker)boxthroughmetalelectrical

conduit.

WiresizesmustconformtotherequirementsoftheNational

ElectricalCodeANSI/NFPA70—latestedition*,orCSA

Standards C22.1-94, Canadian Electrical Code Part 1 and

C22.2 No. 0-M91 - latest edition** and all local codes and

ordinances.

AU.L.-orC.S.A.-listedconduitconnectormustbeprovided

ateachendofthepowersupplyconduit(attherangehood

andatthejunctionbox).

Copies of the standards listed may be obtained from:

*NationalFireProtectionAssociationBatterymarchParkQuincy,

Massachusetts 02269

**CSAInternational8501EastPleasantValleyRoadCleveland,

Ohio44131-5575

Before installing the hood

Forthemostefcientairowexhaust,useastraightrun

or as few elbows as possible.

CAUTION:Ventunittooutsideofbuilding,only. 

Atleasttwopeoplearenecessaryforinstallation. 

Fittings material is provided to secure the hood to most

 typesofwalls/ceilings,consultaQualiedInstaller, 

 checkiftheyperfectlytwithyourcabinet/wall. 

Donotuseexducting.    

COLDWEATHERinstallationsshouldhaveanadditional

 backdraftdamperinstalledtominimizebackwardcoldair

 owandanonmetallicthermalbreaktominimize 

conduction of outside temperatures as part of the

 ductwork.Thedampershouldbeonthecoldairsideof

the thermal break.

 Thebreakshouldbeascloseaspossibletowherethe

ducting enters the heated portion of the house.

Make-upair:Localbuildingcodesmayrequiretheuseof

 Make-upairSystemswhenusingDuctedVentilation 

 SystemsgreaterthanspeciedCFMofairmovement.

 ThespeciedCFMvariesfromlocaletolocale.Consult

 yourHVACprofessionalforspecicrequirementsinyour

area.

1.

2.

3.

4.

5.

6.

5

List of Materials

Parts supplied

Removing the packaging

CAUTION!

Removing the packaging

CAUTION:Wearglovestoprotectagainstsharpedges.First

remove the carton carefully and take out the duct cover.

CAUTION:Removecarefullytheglasscanopyfromthebox

and put it on a smooth safe surfaces.

Grasp the hood structure from the body and lift straight off the

box.

Remove and properly discard every carton and plastic wrap-

ping content in the package.

Remove parts out of the box, duct covers and other contents.

WARNING!

Removetheprotectivelmcoveringtheproductbefore

putting into operation.

Hoodcanopyassemblywithblower,transition.

2Lampsalreadyinstalled.

Greaselter.

Duct cover.

Hardwarebagwith:

Template.

Ductcoversupportbracket(1piece)

Use, care and installation guide

Woodscrews(6pieces-3/16”x1”3/4)

Hoodattachmentanchors

2 - 8x40 anchors

4 - 10x50 anchors

Assemblyscrews

2 - 2.9x6.5 mounting screws

2 - 3.5x9.5 mounting screws

•

Parts not supplied

Optional Accessories

DuctlessRecirculatingKit

 TobeusedonlyintheDuctless(Recirculating)version

 includes:2charcoalltersanddeector

ProfessionalStainlessSteelGreaselter

Tools/Materials required

Wire nuts

Tapetomounttemplate

6”roundedmetalductlengthtosuitinstallation

Measuring tape

Pliers

Gloves

Knife

Safety glasses

Electricdrillwith5/16”and3/8”Bits

Strain relief

Spirit level

Duct tape

Screwdrivers:

Phillips(Posidrive)#2

Torx#2

Wire cutter/stripper

Masking tape

Hammer

Saw, jig saw or reciprocating saw

•

Dimensions and Clearances

*Ductless(Recirculating)versionOnly

**DuctingversionOnly

30” (76.2cm)

36” (91.2 cm

1½”

(4 cm)

20” (50.8 cm)

24

1

/

8

”

(61 cm)

10”

(25.4 cm)

7¼” (18.4 cm

*28

7

/

8

” (73.3 cm) min

*42

1

/16” (106.9 cm) max

**28

3

/

8

” (72 cm) min

**38” (96.6 cm) max

6”

8

1

/

8

” (20.7 cm

6

Ducting Options and Examples

Closely follow the instructions set out in this manual.

Allresponsibility,foranyeventualinconveniences,damagesorrescausedbynotcomplyingwiththeinstructionsinthis

manual, is declined.

Venting methods

ThehoodisequippedwithatransitionB for discharge of fumes to the outside (Ducting version).

Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the Ductless

(Recirculating) version.Attachacharcoallterandthedeector F on the duct cover support bracket G. Fumes and vapours

are recycled through the top grille H by means of a duct connected to the transition Bandthetransitionmountedonthedeec-

tor F.

NOTE: For ductless (Recirculating) version only: purchase the Ductless Recirculating Kit.

Minimum Duct Size (Ducting/Ductless version): 6” Round Pipe.

Preparation

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be

constructed.

Fittings material is provided to secure the hood to most types of walls/ceilings.

However,aqualiedtechnicianmustverifysuitabilityofthematerialsinaccordancewiththetypeofwall/ceiling.

Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

CAUTION:

FOR 9’ CEILINGS: MOUNT THIS HOOD SO THAT THE BOTTOM EDGE IS AT 30” (76,2 CM) MINIMUM ABOVE THE

COOKING SURFACE.

Check your ceiling height and the hood height maximum before you select your hood.

UseonlyMetalductsystem.DONOTuseexibleplasticducting.

NOTE:Anyhomeventilationsystem,suchasaventilationhood,mayinterrupttheproperowofcombustionairandexhaust

requiredbyreplaces,gasfurnaces,gaswaterheatersandothernaturallyventedsystems.

Tominimizethechanceofinterruptionofsuchnaturallyventedsystems,followtheheatingequipmentmanufacturer’sguide

-

linesandsafetystandardssuchasthosepublishedbyNFPAandASHRAE.

ThisHoodMustUsean6”RoundDuct.

•

Pipe

Transition(B)

Roof pitch w/

Flashing and cap

Pipe

Transition(B)

Sidewall cap

with gravity

damper

Pipe

Transition(B)

Charcoal

lter

Deector(F)

Topgrille(H)

Supportbracket(G)

VerticalDischarge

Recirculating

7

Mounting the duct cover bracket

Option A - Fixed heigh duct cover

Fromthehorizontallinetracedintheprevioussection,

 traceahorizontalparallellineasshownbelow.

Centerthebracketinthetophorizontallineandalignit

with the centerline, as described in the followinG

drawing.

Mark screw holes locations in the wall.

IMPORTANT. Check to be sure that holes locations are

leveled, and correctly centered by the vertical centerline.

Drill5/16”pilotholesinthemarkedlocations.

Install wall fastener anchors.

Drive wood screws, by hand, into the fasteners to allow an-

chors to expand. Remove screws.

Secure the bracket to the wall with wood screws and/or

fasteners.

Option B - Telescopic duct cover

Theductbracketshouldbeinstalledagainstthebackwall

andushwiththeceiling.Thisbracketwillholdthe

ductcoverinplaceatthetop(thisaextraaccessoryavailable

notincludedwiththehood).

Secure the bracket to the wall:

Alignthemarkedcenterlineonthebracketwiththe

centerline on the wall.

Mark 2 screw hole locations in the wall.

Drill5/16”pilotholesinthemarkedlocations.

Install wall fastener anchors.

Drive wood screws, by hand, into the fastener to allow

anchors to expand. Remove the screws.

Secure the bracket to the wall with wood screws and/or

fasteners.

•

Ceiling ducting

If the duct will vent straight up to the ceiling:

Use level to draw a line straight up, from the centerline on

the template to the ceiling.

Measureatleast4-12/16”fromthebackwalltothecircle

 centerofan6-½”holeontheceiling.

Wall ducting

If ductwork will vent to rear:

Use a level to draw a line straight up from the centerline

on the template.

Measureatleast23-12/16”(themeasuremightvary

 dependigontheelbowused)abovethepencillinethat]

indicates the bottom installation height, to the circle center

 ofan6-½”diameterducthole(Holemaybeelongatedfor

 ductelbow).

House wiring location

Thejunctionboxislocatedonthetopleftsideofthehood.

Wiringshouldenterthebackwallatleast20”abovethe

 bottomoftheinstallationheight,andwithin5-7/8”and

 4-7/8”oftheleftsideofthecenterline.

•

Centerline

Bracket line

27

28

/32”

Horizontalstraightpencilmarkedline

Desired installation height

VerticalCenterline

C

e

i

l

i

n

g

Wall

For ceiling vent ducting4

12

/16”circlecenter

to wall

Ceiling

6½”diameterhole

FORWALLVENTDUCT

Circle center at

23

12

/16”abovethe

marked bottom

pencil line

Horizontalstraight

pencil line

8

Install framing for hood support

If drywall is present, mark the screw hole locations.

Remove the template.

Cut away enough drywall to expose 2 vertical studs at

the holes location indicated by the template.

 Installtwohorizontalsupportsatleast4X2”between

two wall studs at the bottom and upper mounting holes

installation location.

Thehorizontalsupportmustbeushwiththeroomside

of the studs.

Use cleats behind both sides of the support to secure to

wall studs.

Reinstallldrywallandrenish

IMPORTANT-Framingmustbecapableofsupporting100lbs.

Mounting the hood

WARNING:2peoplearerequiredtoliftandpositionthehood

onto the mounting screws.

Placethetemplateonthewallalongthehorizontalline,

make sure the template is leveled and centered with the

centerline.

Mark“upper”screwholeslocationsinthewall.

IMPORTANT.Checktobesurethatholelocationsare

leveled and correctly centered by the vertical centerline.

Drive“upper”woodscrewsbyhand.Leave¼“of

distance between the screw head and the wall.

Removethegreaselterandmountthehoodontothe

 “upper”screws.

•

6-1/2”min.openingforductwork

Viewfromrear

cleats

1”x6”min

Mounting Support

Centerline of

installation

space

Mark“lower”woodscrewholeslocationsinthewallusing

a pencil.

Remove the hood.

Drive“lower”woodscrews,byhand.Removescrews.

Mountthehoodontothe“upper”screws.

Driveandtightenthe“upper”woodscrews,byhand.

Driveandtightenthe“lower”woodscrews,byhand.

Connecting the ductwork

Install ductwork, making connections in the direction of

 airowasillustrated.

Push duct over the exhaust outlet.

Wrapallductjointsandtheangeconnectionswithduct

tape for an airtight seal.

Make the same connection in the wall or ceiling vent exit.

•

A.Airow

B. Duct tape over seam

A

B

C

9

Electrical connection

WARNING

Electrical Shock Hazard

Warning: Turn off power circuit at the service panel

before wiring this unit.

120 VAC, 15 or 20 Amp circuit required.

ELECTRICAL GROUNDING INSTRUCTIONS

THISAPPLIANCEISFITTEDWITHANELECTRICAL

JUNCTIONBOXWITH3WIRES,ONEOFWHICH

(GREEN/YELLOW)SERVESTOGROUNDTHE

APPLIANCE.TOPROTECTYOUAGAINST

ELECTRICSHOCK,THEGREENANDYELLOWWIRE

MUSTBECONNECTEDTOTHEGROUNDINGWIRE

INYOURHOMEELECTRICALSYSTEM,ANDIT

MUSTUNDERNOCIRCUNSTANCESBECUTOR

REMOVED.

Failure to do so can result in death or electrical

shock.

Disconnect power.

Remove terminal box cover.

RemovetheknockoutintheterminalboxandinstallaUL

 listedorCSAapproved½”strainrelief.

Runhomepowersupplywiringthrough½”strainrelief

into terminal box.

UseULlistedwireconnectorsandconnectwhitewires

 (B)together.

UseULlistedwireconnectorsandconnectblackwires

 (C)together.

1.

2.

3.

4.

5.

6.

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

Connectgreen(orbare)groundwirefromhomepower

 supplytothe2yellow-greengroundwires(D)interminal

 boxusingULlistedwireconnectors.

Tightenstrainreliefscrew.

Install terminal box cover.

Reconnect power.

Mounting the duct cover

Position the duct cover over the mounted hood.

Slide the bottom of the duct into the glass area.

Position the top of the duct over the duct mounting

bracket. If a telescopic duct cover is used, grab the

upper part of the telescopic duct cover, pull it and place it

in the duct cover mounting bracket.

Secure the top of the duct with 2 assembly screws

provided.

7.

8.

9.

10.

•

A

B

C

D

E

A.ULlistedwireconnectors

B.White wires

C. Black wires

D.Green(orbare)wireconnectedto

yellow-green wires

E.Homepowersupply

10

Control and features

Thishoodisequippedwithanelectronicmotorandlamp

control.Thecontrolisabletoset3differentfanspeeds,

turnON/OFFlightandhasatimerfunction.Inthefollowing

drawing are described the main key functions.

Control panel description

1. Timer Key

Thedefaulttimersettingis10minutes,anditcanbe

adjusted between 20 minutes and 1 minute.

Afterpressingthetimerkey,thecontrolenterstoatimer

setup mode, and user can adjust the timer countdown

 timewiththe“-”and“+”keyswithin5seconds.Thetimer

can be initiated immediately pressing the timer key, after

setting the timer duration or pressing the timer key twice

 (default10minutessetting).

If not action occurs within 5 seconds the countdown will start.

Duringthetimersetupthe“-”and“+”keysarededicated

to the timer and no motor action will occur.

Onceinitiatedthetimer,itcanbecancelledbypressing

the timer key again.

2. Light Key

PresslampkeytoturnONthelight(Lampstate

 previouslyOFF).

PresslampkeytoturnOFFthelight(Lampstate

 previouslyON).

3. Display

Shows the hood settings.

4. “-” Key. Speed Decrease / OFF

Thiskeyisusedtodecreasethefanspeed,orturnOFFthefan.

ThefanwillturnOFFifthe“-”keyispressedandthe

 hoodwasintherstspeed.

Ifthefanisatsecondspeedandthe“-”keyispressed,

 thefanwillbesettorstspeed.

Ifthefanisatthirdspeedandthe“-”keyispressed,the

fan will be set to second speed.

IfthefanisOFFandthe“-”keyispressed,thecontrol

backlight will light up.

5. “+” Key. Speed Increase / ON

Thiskeyisusedtoincreasethefanspeed,orturnONthefan.

ThefanwillturnONifthe“+”keyispressedandthe

 hoodwasOFF.

Ifthefanisatrstspeedandthe“+”keyispressed,

the fan will be set to second speed.

Ifthefanisatsecondspeedandthe“+”keyispressed,

the fan will be set to third speed.

Ifthefanisatthirdspeedandthe“+”keyispressed,

a beep will sound.

Special functions

Clock programming

Theclockcanbereprogrammedatanytimeexcept

during an active timed function.

Theclockcanbedisplayedinatwelvehourformatand

valid clock times are from 1:00 to 12:59.

Theclockcanbereprogrammedpressingthe“Timer”

•

Description of the hood &

Controls

Control panel

CoverLamp

GreaselterreleaseHandle

Greaselter

Duct cover

Duct cover grid

1.

2.

3.

4.

5.

6.

1 2 3

11

key for 5 seconds, and after, the clock can be adjusted

 withthe“+”and“-”keys.Colon“:”willashindicating

clock programming mode.

Theusercanhaveminuteincrements/decrementsof1

 minute,butiftheuserkeeppressingthe“+”/”-”keys

for more than 1 second, the increments / decrements will

be of 5 minutes. During this option the control will

round to the nearest 5 minutes.

Theusercannishonreprogrammingtheclockpressing

 the“timer”key.

After1minuteofnokeypressedthecontrolwillaccept

the programmed clock time and will add one minute

to the set clock.

Grease lter saturation alarm

Afterthirtyfanfunctionalhours,thedisplaywillshow 

 “GreaseFilter”ifthefanisactive.Whenthisiconis

 showninthedisplay,thegreaseltersinstalledare

required to be washed.

Toresetthegreaseltersaturationalarmtheusermust

 pressthe“+”keyfor5seconds,afterthisactionthe

 icon“greaselter”isnotdisplay,andthehoodhasthe

normal display operation.

Charcoal lter saturation alarm (Recirculating accessories)

Afteronehundredandtwentyfunctionalhoursofthefan,

 thedisplaywillshow“CharcoalFilter”ifthefanisactive.

 Whenthisiconashesondisplay,thecharcoallters

installed are required to be replaced or reactivated.

Toresetthegreaseltersaturationindicationtheuser

 mustpressthe“-”keyfor5seconds,afterthistime

 theicon“charcoallter”isnotdisplayandthehoodhas

the normal display operation.

Audible signal activation and deactivation

Theaudiblesignalscanbeactivatedordeactivated

 pressingthe“Light”keyfor5seconds.

If the audible signal is activated, a tone must sound and

 the“Snd”symbolmustappearonthedisplayfor2second.

Iftheaudiblesignalisdeactivated,the“Snd”symbolmust

appear on the display for 2 second and no sound must sound.

Charcoal lter inclusion and exclusion

(Recirculating accessories)

Thecharcoallterinclusionorexclusioncanbesetby

 pressingthe“-”and“+”keysatthesametimefor5seconds.

TheInclusionorexclusionofcharcoalltermustbe

 selectedwhilethelampsandthemotorareOFF.

Whenthecharcoalhasbeenexcluded,thecharcoallter

alarm is disabled.

Heat sensor

Thecontrolisequippedwithaheatsensorthatwillturn

on the blower at second speed if excessive heat

 occurs(over70°C)surroundingthecontrolarea.

IftheblowerisOFForifitisoperatingatrstspeed,the

blower will be set automatically to second speed.

During this state, the user may raise the blower speed to

third speed but can not decrease the speed.

When the temperature level on the hood drops to normal,

 theblowerwilloperateinthesettingdenedbytheuser

before the alarm occured.

•

Maintenance

Metal Grease Filter Maintenance

Themetalltertrapsgreasereleasedbyfoodsonthecook-

top.Theltermustalwaysbeinstalledwhenthehoodis

operating / used.

To remove:

Pushthelterlock/pivotindirectiontothecenterofthe

 lter.

Oncethepivotispushedpulldownthelterslowly.

To replace:

Inserttheltertabsintotheslots

Pushthelterlock/pivotindirectiontothecenterofthe

 lter.

Oncethepivotispushed,raisethelterslowlyuntilthe

top and release the pivot.

To clean:

Swishthelterinhotsoapywaterandrinseinclean

water or wash it in the dish washer.

Do not use abrasive cleaners.

Hood maintenance

Clean with a damp, soapy cloth and dry with a clean cloth.

 Aglasscleanermayalsobeused.

 ATTENTION:Donotwetthecontrolpanel.

Do not use a steel wool pad; it will scratch the surface.

Tocleanthestainlesssteelsurface,usewarmsudsy

 water,stainlesssteelcleanerorpolish.Alwayswipe

the surface in the direction of the grain. Follow the cleaner

instructions for cleaning the stainless steel surface.

•

12

Replacing the incandescent light bulb

CAUTION: Before replacing the lamps, disconnect power off

to prevent from being switched on accidentally.

UseaPhillips#2screwdrivertoremovethelamp

cover. Remove it carefully from its housing.

Removethedamagedlampbulb(turncounter

 clockwise)andreplaceitwithanewbulb.E12Philips

 Lamp120V,40W.

Available Accesories

Charcoal Filter

If the model is not vented to the outside, the air will be recir-

culatedthroughdisposablecharcoalltersthathelpremove

smoke and odors.

Thecharcoallterscannotbecleaned.

Theymustbereplaced.

Cover the grill that protects the suction motor with the carbon

ltersothattheslotsontheltercorrespondtothepinson

the sides of the motor protection grill.

Turnthecarbonlterclockwisetoblockthem(bayonetxing).

Thecharcoalltersshouldbereplacedevery4-6months

(dependingonhoodusage).

NOTE: DO NOTrinse,orputcharcoalltersinanautomatic

dishwasher.

NOTE: Charcoalltersarenotincludedwiththehood.

Theymustbeorderedfromyoursupplier.

Ordertheneededkitspecifyingyourhoodmodelandwidth

size.

1.

2.

Air deector installation (Recirculating version)

Assembletheairdeectorwiththeductcoverbracket

with 2 - assembly screws provided.

A

C

B

Measurefromthebottomoftheairdeectortothe

bottom of the hood outlet.

X

A

C

D

B

E

Cuttheducttothemeasuredsize(X).

Removetheairdeector.

Slidetheductontothebottomoftheairdeector.

Placetheassembledairdeectorandductoverthe

exhaust outlet from the hood.

Reassembletheairdeectortotheductcoverbracket

with 2 assembly screws.

Seal connections with vent clamps.

1.

2.

3.

4.

5.

6.

7.

8.

A.Ventcoverbracket

B. 2.9 x 6.5 mm screws

C.Deector

A.Airdeector

B.Ventclamp

C.X=lengthtocutventduct

D.Ventduct

E. Exhaust outlet

13

Warranty

ELICA North America TWO-YEARS LIMITED WARRANTY

TO OBTAIN SERVICE UNDER WARRANTY

Ownermustpresentproofoforiginalpurchasedate.Pleasekeepacopyofyourdatedproofofpurchase(salesslip)inorderto

obtain service under warranty.

PARTS AND SERVICE WARRANTY

Fortheperiodoftwo(2)yearsfromthedateoftheoriginalpurchase,Elicawillprovidefreeofcharge,nonconsumablepartsor

componentsthatfailedduetomanufacturingdefects.Duringthesetwo(2)yearslimitedwarranty,Elicawillalsoprovidefreeof

charge, all labor and in-home service to replace any defective parts.

WHAT IS NOT COVERED

DamageorfailuretotheproductcausedbyaccidentoractofGod,suchas,ood,reorearthquake.

Damageorfailurecausedbymodicationoftheproductoruseofnon-genuineparts.

Damage or failure to the product caused during delivery, handling or installation.

Damage or failure to the product caused by operator abuse.

Damage or failure to the product caused by dwelling fuse replacement or resetting of circuit breakers.

Damage or failure caused by use of product in a commercial application.

Service trips to dwelling to provide use or installation guidance.

Lightbulbs,metalorcarbonltersandanyotherconsumablepart.

Normalwearofnish.

Weartonishduetooperatorabuse,impropermaintenance,useofcorrosiveorabrasivecleaningproducts/padsandoven

cleaner products.

WHO IS COVERED

ThiswarrantyisextendedtotheoriginalpurchaserforproductspurchasedforordinaryresidentialuseinNorthAmerica(Including

theUnitedStates,Guam,PuertoRico,USVirginIslands&Canada).

Thiswarrantyisnon-transferableandappliesonlytotheoriginalpurchaseranddoesnotextendtosubsequentownersof

theproduct.Thiswarrantyismadeexpresslyinlieuofallotherwarranties,expressedorimplied,including,butnotlimitedto

anyimpliedwarrantyofmerchantabilityortnessforaparticularpurposeandallotherobligationsonthepartofElicaNorth

America,provided,however,thatifthedisclaimerofimpliedwarrantiesisineffectiveunderapplicablelaw,thedurationofany

impliedwarrantyarisingbyoperationoflawshallbelimitedtotwo(2)yearsfromthedateoforiginalpurchaseatretailorsuch

longer period as may be required by applicable law.

Thiswarrantydoesnotcoveranyspecial,incidentaland/orconsequentialdamages,norlossofprots,sufferedbytheoriginal

purchaser, its customers and/or the users of the Products.

WHO TO CONTACT

ToobtainServiceunderWarrantyorforanyServiceRelatedQuestion

Please Call:

ElicaNorthAmericaAuthorizedServiceat(888)732-8018      

OrbyWritingTo:

ElicaNorthAmerica,AttentionCustomerService,222MerchandiseMartPlaza    

 Suite947,Chicago,IL60654USA

[email protected]

•

Page is loading ...

LI30UA Ed.04/12 Printed in Mexico

ELICA EVL436S1 Install Instructions Volterra

ELICA EVL436S1 Install Instructions Volterra

in other languages

Related papers

Other documents