Features
•
Compression molded from our exclusive solid Vikrell
®
material
•
Innovative four-piece modular design for seamless
appearance
•
Tongue-and-groove 4-piece modular design allows for
easy ″snap together″ installation
•
Durable high-gloss finish
•
10-year consumer/3-year commercial limited warranty
•
Left or right drain
•
Available with or without above-the-floor drain
•
Wall surround allows for attachment of grab bars
•
60″ (152.4 cm) x 31-1/2″ (80 cm) x 75-3/4″ (192.4
cm) complete unit rough-in dimensions include flange
•
60″ (152.4 cm) x 30″ (76.2 cm) x 74-1/4″ (188.6 cm)
complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
•
ANSI Z124.1.2
•
ASTM E162
•
ASTM E662
•
CSA B45.0
•
CSA B45.5
60″ (152.4 cm) BATH/SHOWER
SYSTEM WITH BACKER BOARDS
71090116
Colors/Finishes
•
0: White
•
Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Complete Unit Description Colors/Finishes
71090116 60″ (152.4 cm) bath and wall surround with backer boards, left drain ❑ 0 ❑ Other_____
71090118 60″ (152.4 cm) bath and wall surround with backer boards, above-the-floor left drain ❑ 0 ❑ Other_____
71090126 60″ (152.4 cm) bath and wall surround with backer boards, right drain ❑ 0 ❑ Other_____
71090128 60″ (152.4 cm) bath and wall surround with backer boards, above-the-floor right drain ❑ 0 ❑ Other_____
Model Wall Component Description Colors/Finishes
71094106 Complete wall set with backer board locations ❑ 0 ❑ Other_____
ACCLAIMTM
Page 1 of 2
1065806-4-
D
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING
Technical Information
Fixture:* basin area top area
Bathing
well
42″ (106.7 cm) x
16-1/4″ (41.3 cm)
56″ (142.2 cm) x
23-3/4″ (60.3 cm)
water depth capacity
To overflow 12″ (33 cm) 34 gal (128.7 L)
* Approximate measurements for comparison only.
Model Door maximum
width
Door maximum
height
71090116
71090118
71090126
71090128
71090416
71090426
58-1/2″
(148.4 cm)
56-1/2″
(143.5 cm)
Installation Notes
Install this product according to the installation guide.
Size the drain cutout to fit the drain assembly that will be
used.
End stud positioning is critical if nailing-in flanges are to be
used.
Double studding is recommended for pivot shower door
installations.
Studs should be positioned roughly as shown.
Attach grab bars at the specified backer board locations only.
Adjacent finished wall thickness must not exceed 9/16″
(1.4 cm).
15"
(38.1 cm)
3" (7.6 cm)
60" (152.4 cm)
4" (10.2 cm)
30" (76.2 cm)
Drain Cutout
2-3/4" (7 cm)
Overflow Detail
2" (5.1 cm)
60-1/8" (152.7 cm) Min
60-1/4" (153 cm) Max
Recommended Support
Clip (5 Total)
Note: Right and left end walls
are the same, only mirrored.
Backer board locations
11"
(27.9 cm)
21" (53.3 cm)
3-1/2"
(55.9 cm)
3-1/2" (8.9 cm)
3-1/4"
(8.3 cm)
Back Wall
18" (45.7 cm)
Grab Bar
8-3/4"
(22.2 cm)
22-1/4"
(56.5 cm)
8" (20.3 cm)
16" (40.6 cm)
8"
(20.3 cm)
14"
(35.6 cm)
6" (15.2 cm)
(Typical)
31-1/2"
(80 cm)
14-1/4"
(36.2 cm)
2" (5.1 cm)
D. Drain
3-1/2"
(8.9 cm)
End Wall
10" (25.4 cm)
Grab Bar
24" (61 cm)
Grab Bar
22"
(55.9 cm)
4-3/4"
(12.1 cm)
2" (5.1 cm)
1" (2.5 cm)
22"
(55.9 cm)
19"
(48.3 cm)
18"
(45.7 cm)
1"
(2.5 cm)
2-1/2"
(6.4 cm)
31-1/2" (80 cm)
30"
(76.2 cm)
1-1/2"
(3.8 cm)
54"
(137.2 cm)
1-1/2"
(3.8 cm)
73-1/2"
(186.7 cm)
Product Diagram
ACCLAIMTM
ACCLAIMTM 60″ (152.4 cm) BATH/SHOWER SYSTEM WITH BACKER BOARDS
Page2of2
1065806-4-
D
/