2. OSP Furniture
  3. A2EB212-B

OSP Furniture A2EB212-B, A2EB212-GR Operating instructions

  • Hello! I've reviewed the operating instructions for the OSP Furniture A2EB212 Height Adjustable Base. This document includes important information about setting up the desk, using the height adjustment feature, and safety precautions. The document also outlines a 3 year warranty against materials and workmanship defects. I am ready to answer any specific questions you have about the desk outlined in this manual.
  • What is the desk warranted against?
    How often should I check the bolts and screws?
    What should I use to clean the desk?
A2EB212
48”W HEIGHT ADJUSTABLE BASE
OPERATING INSTRUCTIONS
WARNING
1. Do not use this product unless all bolts, screws and knobs
are securely tightened.
2. Check that all bolts, screws and knobs are tight every three
months or as needed.
3. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
4. Do not use product as a stepladder.
5. Use this product for its intended purpose only.
6. Use mild detergent only for cleaning.
LIMITED WARRANTY
A2EB212 is warranted from the original purchase date to the original purchaser for normal commercial usage - defined as a standard
forty-hour work week - according to the below-listed schedule and limitations.
 •3yearwarranty
 •Warrantedagainstfailureduetomaterialsandworkmanship
Warranty Exclusions
This warranty will not cover labor, freight, or damage from misuse, abuse, negligence, alteration, assembly, installation, attachments,
accident, vandalism, acts of nature or any other event beyond our control. The warranty does not cover cosmetic damage that may
result from normal use. Liability for incidental or consequential damage is excluded. The user assumes all risk of injury resulting from
use of this product.
This warranty applies only to products purchased through authorized dealers and products sold within the United States of
America and the Commonwealth of Canada. This warranty does not apply to products used for rental purposes. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
IMPORTANT
Desk must be reset before operation.
See Step 6.
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Align Side Supports (B) with Frame/Leg Set (A) on underside of Desk Top.
STEP 2 Secure Side Supports (B) to Frame/Leg Set (A) with four Screws (F) and Allen Key (J). FULLY TIGHTEN ALL SCREWS.
STEP 3 Route Handset (E) Cable through the hole below the Left Trunk. Plug both Handset and Motor Cables into Control Box (D).
PART QTY
A. Frame/Leg Set ......................1
B. Side Support ........................2
C. Feet ...............................2
D. Control Box .........................1
E. Handset ............................1
F. Screw M6x12 ........................4
G. Screw 5x22 .........................9
H. Screw 3.5x16 .......................4
I. Screw M10x35 .......................8
J. Allen Key 4 ..........................1
K. Power Cable ........................1
A2EB212
48”W HEIGHT ADJUSTABLE BASE
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
a
b
b
Motor Cable
j
f
e
d
a
b
b
Motor Cable
j
f
e
d
a
b
b
Motor Cable
j
f
e
d
STEP 3
A2EB212
48”W HEIGHT ADJUSTABLE BASE
ASSEMBLY INSTRUCTIONS
STEP 4
STEP 5
STEP 4 Align Frame/Side Supports on Desk Top. Secure Frame/Side Supports to Desk Top with nine Screws (G). Secure Control Box (D) to Desk Top with
two Screws (H). Locate Handset in preferred position and secure to Desk Top with two Screws (H). FULLY TIGHTEN ALL SCREWS.
STEP 5 Secure Feet (C) to Frame/Legs using four Screws (I) per foot and Allen Key (J). FULLY TIGHTEN ALL SCREWS. Attach Power Cable (K) to Control
Box (D). ONCE ALL SCREWS ARE FULLY TIGHTENED AND ALL CABLES ARE SECURELY FASTENED, TURN DESK UPRIGHT.
g
h
h
g
i
j
k
g
h
h
g
i
j
k
S
231 4
28.1
the lowest position
S2 31 4
SET
A2EB212
48”W HEIGHT ADJUSTABLE BASE
ASSEMBLY INSTRUCTIONS
© Office Star Products January 2021
IMPORTANT
Youmustresetthedesk’scontrolbox,usingthehandset,asshownbelow,priortouse.
STEP 6
Plug Power Cable (K) into wall outlet. Press and Hold the up/down buttons for more than 3
seconds;untilthescreenshows“SET”.
Continue pressing both buttons and both legs will
descend to lowest position.
After a beeping sound is heard and the screen
shows“28.1”,youcanreleasethebuttons.
Your desk is now operational.
/