Classic Exhibits VK-1902 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-1902
Type
Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902 General Layout
10’
10’
Plan View
www.classicexhibits.com
Step 2
Page 2 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902 General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902 Backwall Assembly
11
Item
1
2
3
4
5
6
7
11
Qty.
1
1
1
1
1
1
1
2
Steps:
1) Connect lower verticals [2, 5 and 7] to base plates [1 and 4].
2) Connect upper verticals to lowers verticals [3 to 2 and 6 to 5].
3) Connect shelf supports [11] to curved vertical [7],
then slide counter top on vertical [7] and rest on top of supports.
Description
Base Plate
47.875” Vertical Extrusion
47.875” Vertical Extrusion
Base Plate
47.875” Vertical Extrusion
47.875” Vertical Extrusion
47.576” Curved Vertical Extrusion
Counter Support
1
3
2
4
6
5
7
C
D
Slide on vertical
11
7
11
11
Stoppers
Slide slot on round plate on extrusion #7
and slide locks located on inner end
of extrusions #11’s into grooves of
extrusion #7 atop stoppers,
then tighten setscrews to secure
*** Round plate and horizontals #11
stay assembled when shipping**
Slide screws located on underside
of counter into holes on round plate
and secure with wing nuts
Loosen screw
and remove
#11 if needed
for easier
installation
Knob
Knob
Connection
Bar C
Slide connecting bar
between verticals,
tighten knobs to secure
Screwcaps and connectors
for graphic frame attachment
stay attached to verticals
when shipping in jigged cases
www.classicexhibits.com
Step 2
Page 2 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902
Large Frame Assembly
Item
12a/12b/12c
13a/13b/13c
14a/14b
15a/15b
Qty.
1/1/1
1/1/1
1
1
Steps:
1) Connect TSP pieces together [a to b to c]
2) Assemble SEG frame assemblies together.
Description
35.6954” TSP Horizontal Extrusion
35.6954” TSP Horizontal Extrusion
29” TSP Vertical Extrusion
29”h TSP Vertical Extrusion
12a 12b
13a 13b
14a 15a
Graphic Removal
Graphic: To Ensure Proper Fit
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternater corner then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
12c
13c
14b
15b
*** Must apply SEG graphic AFTER
attaching frame to backwall verticals ***
Insert lock into extrusion,
then tighten setscrew to secure
Insert
Corner
Connection
Straight
Connection
and tighten knob
to secure
Slide connecting
bar between
verticals/horizontals
A
B
AA
A
B
www.classicexhibits.com
Step 3
Page 3 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902
Header Frame Assembly
Item
16a/16b/16c
17a/17b/17c
18
19
Qty.
1/1/1
1/1/1
1
1
Steps:
1) Connect TSP pieces together [a to b to c]
2) Assemble SEG frame assemblies together.
3) Apply SEG graphic to assembled frame.
Description
35.33” TSP Horizontal Extrusion
35.6954” TSP Horizontal Extrusion
23” TSP Vertical Extrusion
15” TSP Vertical Extrusion
Graphic Removal
Graphic: To Ensure Proper Fit
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternater corner then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
16a 16b 16c
17a 17b
17c
18 19
Insert lock into extrusion,
then tighten setscrew to secure
Insert
Corner
Connection
Straight
Connection
and tighten knob
to secure
Slide connecting
bar between
verticals/horizontals
B
Welded Corner
B
B
B
www.classicexhibits.com
Step 4
Page 4 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902
1
3
2
4
5
7
6
8
Steps:
Assemble frame together in numerical order.
Apply pillowcase graphic to assembled frame.
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Frame Assembly
www.classicexhibits.com
Step 5
Page 5 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902
Frame Attachment
Item
8
9
10
Qty.
1
1
1
Steps:
1) Attach assembled large SEG frame to vertical extrusions
using screwcaps provided.
2) Apply SEG graphic to frame.
3) Attach horizontal [10] to vertical [6] atop large frame.
4) Attach center frame with pillowcase graphic to backwall verticals by
slide connector pieces into groove of vertical from top.
5) Attach upper frame to backwall verticals and secure with
connectors as shown.
6) Attach curved vertical [8] to bottom curved vertical [7], see
detail E on General Info Page.
7) Lock front end of horizontal [11] to back of vertical [8].
8) Attach round sign at vertical [8] as shown.
9) Attach horizontal [9] to vertical [5] and lock
top of vertical [8] to bottom of horizontal [8].
Description
47.576” Curved Vertical Extrusion
8” Horizontal Extrusion
10.375” Horizontal Extrusion
*
*
Secure with bolt
*
*
Rest header frame
on connectors*
D
Refer to
detail “E”
on Pg 2
Screwcap
Screwcap
Use screwcaps to secure
frame to backwall vertical
extrusions. Then apply SEG
graphic to assembled frame.
*
*
8
10
9
*** Screwcap goes
between graphic and frame
6
Example of Graphic Attachment
Graphic
Cap
Standoff
Barrel
Slide connector on back of standoff
barrels into groove of extrusion from top
and twist to secure in place. Secure graphic
to standoffs using screw caps.
5
7
2
3
www.classicexhibits.com
Step 6
Page 6 of 6
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902 Pedestal Assembly
Item
20
21
22
23
24
25
26
27
28
29
30
Description
40” Vertical Extrusion
40” Vertical Extrusion w/ Hinges
40” Vertical Extrusion w/ Stopper
40” Vertical Extrusion
S-curved Horizontal
22” Horizontal Extrusion
22.264” Horizontal Extrusion
25.678” Horizontal Extrusion
32” Vertical Extrusion
22” Horizontal Extrusion
25.678” Horizontal Extrusion
Qty.
1
1
1
1
2
1
2
1
1
1
1
Steps:
1) Connect lower horizontal extrusions beween verticals approx at 4.5” from ground on stoppers as shown.
2) Attach door where indicated.
3) Place insert infills and attach vertical [28] where indicated.
4) Connect upper horizontal extrusions between verticals as shown.
5) Velcro shelf supports to inside of assembled pedestal atop floor.
6) Set internal shelf on shelf supports.
7) Set counter top on assembled pedestal.
Door Hinges
Door Stop
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
20
21
22
23
24
25
26
27
Laminated side
face outside
24
28
26
29
30
Door
White Infill
Graphic Infill
Shelf Supports
4.5”
Horizontals [25 and 27]
havea lip for floor
to rest upon.
*
*Velcro strip
for shelf support
attachment
Door
Lower horizontals
sit on stoppers.
27
Floor
Internal Shelf
Counter Top
www.classicexhibits.com
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902
Top View of each Case
Level 1 (Bottom) Level 2 Level 3
Lights
Setup Hardware
Counter Top and
Shelf Support
Base Plates
6
7
8
5
2
15a 15b
3
Case Packing Instruction - Case 1 of 3
www.classicexhibits.com
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902
Top View of each Case
Level 1 (Bottom) Level 2 Level 3
13a
13b
13c
12a
12b
12c
14a
14b
Graphics
Case Packing Instruction - Case 2 of 3
www.classicexhibits.com
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1902
Top View of each Case
Level 1 (Bottom) Level 2 Level 3 Level 5Level 4
24
25
29
26
26 30 28
27
21
22
20
23
Door 2-piece Counter Top
Inserts Internal Shelf Supports
Floor and Internal Shelf
Case Packing Instruction - Case 3 of 3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Classic Exhibits VK-1902 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-1902
Type
Setup Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents