Classic Exhibits VK-1352 Setup Instructions

Brand: Classic Exhibits

Model: VK-1352

Type: Setup Instructions

Order #XXXXX

Top View

Perspective View

10’

VK-1352 General Layout

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

VK-1352 Grid View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

1) Locate channels along the edges of extrusions

2) Insert graphic corners first into channels then center

point of graphic into channels. Allows for proportional

fit around the perimeter of the extrusion.

3) Working from center to corner, slide silicon edge

on graphic into channel.

4) After all edges of graphic have been inserted into

channels, step back and assess graphic fit, make

adjustments where needed.

Fold edges over.

Insert into

groove

of frame

SEG Installation

Order #XXXXX

CEI-110 Profile

Straight Bracket Assembly

1) Slide TWO-PIECE TS RV 4 straight bracket into

Interior Center Slot of extrusion, so that two of the

set screws are inside groove. Tighten two set screws

to secure.

3) Slide connecting extrusion over exposed ends of

bracket & connector. Tighten all remaining set screws

to secure extrusions.

2) Slide one V4 Connector into outer interior groove

of extrusion, so that one set screw is inside groove.

Tighten set screw.

TS RV 4

Bracket

Insert two-piece

bracket into the

interior center slot

of extrusion.

Slide V4 Connector

into front interior

groove.

Secure inserted half of

bracket & connector

using set screws.

Slide connecting

extrusion over

exposed ends

of bracket &

connector.

Completed

Assembly

Secure extrusion,

using remaining

set screws.

Set

Screws

Straight Connection

Corner Connection

TS RV 2

Upper

Horizontal

Lower

Horizontal

Upper

Horizontal

Lower

Horizontal

TS RV 2

8 Brackets Total:

(4) - TS RV 2

(4) - A1 L-Brackets

Slide verticals over

brackets of lower

horizontal, then slide

upper horizontal &

brackets into grooves

& center slots

of verticals.

Completed

Assembly

Insert L-Brackets into the

Interior Center Slot & outer

interior grooves of extrusion.

Disassembly

1) Loosen set screws on brackets and slide

extrusions off of brackets.

1) Slide TWO-PIECE TS RV 2 L-bracket into

Interior Center Slot of extrusion so that two

set screws are inside groove.

Tighten two set screws to secure.

2) Slide one A1 L-Bracket into outer interior

grooves of upper and lower horizontals.

Tighten set screws to secure.

4) Slide exposed ends of installed brackets of

upper horizontal into open ends of verticals.

Tighten set screws to secure.

3) Slide vertical extrusion over exposed ends

of brackets in lower horizontal.

Tighten set screws to secure.

Corner Bracket Assembly

CEI-110 Frame Assembly

CEI110 Frame Assembly

Crate 1 of 1

Order #XXXXX

Side View Level 1

Graphics (Qty. 2) Setup Hardware

Level 2 Level 3 Level 4 Level 5

Scale: XX

Assembled

Counter Base

Shelf

Counter Top

Setup

Hardware

2A21A1

Monitor

Mount

Graphics

Graphic

Base Plate

Crate Packing

Step 1 of 7

Order #XXXXX

Item

1,1A

2,2A

Qty.

1,1

Description

88” CEI111 Horizontal Extrusion

90” CEI111 Vertical Extrusion

89.253” Z45 Vertical Extrusion

86.353” Z45 Vertical Extrusion

Base Plate

Steps:

1) Assemble extrusions [1] [1A] [2] and [2A] together.

Can be assembled on the floor then lifted upright.

2) Attach extrustions [3] and [4] inside assembled frame. See Z45 Attachment details.

3) Attach base plates [5] to extrusions [1] [2] and [2A]. See Base Plate Attachment detail.

4) Connect light cords and attach transformers. See Light to Light Connection and

Light to Transformer Connection details.

5) Install SEG graphic to front of assembled frame and blocker fabric to back.

See SEG Graphic Installation sheet for instruction.

Completed Assembly

Base

Plate

Bolts

Bolt

Vertical

Extrusion

Horizontal

Extrusion

Base Plate Attachment

Attach base plate to extrusions,

using bolts, washer, and wing nut.

Washer

Wing Nut

Lights

Male

Female

to power Transformer

144W / 6A / 24V

Light to Light Connection

Light to Transformer Connection

Maximum of 11 lights per transformer.

CEI-111

Z45

Z45 Attachment

Attach Z45 vertical to front

groove of CEI-111 horizontal.

CEI-111

Z45

Z45 Attachment

Attach Z45 vertical to back

groove of CEI-111 horizontal.

Power

Break

Power

Break

Power

Break

VK-1352 Lightbox Assembly

Step 2 of 7

Order #XXXXX

6A 6A

9897

Item

6,6A

Qty.

2,2

Description

30.272” TSP49 Horizontal Extrusion

99.484” TSP49 Curved Vertical Extrusion

91.417” Z45 Vertical Extrusion

Steps:

1) Attach extrusions [7] to extrusions [6] and [6A]. Tighten set screws to secure.

2) Install SEG graphic to front of assembled frame and blocker fabric to back.

See SEG Graphic Installation sheet for instruction.

Completed Assembly

Keep extrusions [6] [6A] [8] and [9] assembled.

VK-1352 Curved Frames Assembly

Step 3 of 7

Order #XXXXX

Standoffs

(4 places)

Completed Assembly

Scale: 30

Screw Caps

(8 places)

Lightbox

TSP49 Frame TSP49 Frame

Steps:

1) Attach assembled curved frames to assembled lightbox, using standoffs and screw caps.

2) Attach monitor mount to lightbox, using standoffs and bolts.

Bolt

Z45

Monitor

Mount

Standoff

Attach standoffs to vertical extrusions, using

bolts then attach monitor mount to standoffs,

using bolts.

Note: Standoffs attach through SEG graphic.

Monitor Mount Attachment

SEG

Screw Cap

TSP49 Frame

CEI111 Lightbox

Standoff

Base Plate

Screw Cap

TSP49 Frame Attachment (top view)

VK-1352 Attachments

Step 4 of 7

Order #XXXXX

Using Your Setup Instructions

The Aero Setup Instructions are created specifically for your configuration. The instructions include an

exploded view of the frame which is sequentially labeled. We encourage you to review the instructions

before attempting to assemble your exhibit.

Connections are kept very simple; no tools required. Everything assembles with push-button connectors.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Push-Button

Numbered Label

Connections are made by holding the button down and

sliding the red tube into opposing tube until button locks

into the hole. To disassemble, push button and pull or twist

extrusions apart.

Connect in alphabetical order as shown.

MOD-1550 Aero Frames

Step 5 of 7

Order #XXXXX

BACK VIEW BACK VIEW BACK VIEW

Steps:

1) Connect lower horizontals [5] [6] and [7] between verticals [1] [2] [3] and [4].

2) Slide lower infill between verticals [2] and [3] then secure with horizontal [7A].

3) Slide infills between verticals [1] [2], [2] [3] and [3] [4] then secure with upper

horizontals [5A] and [7B], making sure Velcro is facing inward.

4) Attach vertical [8] to lower horizontal [6].

5) Connect doors to verticals [1] and [4]. See Door Connection detail.

6) Connect upper horizontal [6A] between verticals [1] and [4] and

attach to vertical [8].

7) Connect shelf supports to Velcro on infills, then place shelf on top of supports.

Item

5,5A

6,6A

7,7A,7B

Qty.

1,1

1,1,1

Description

37.5” S40 Vertical Extrusion w/ Door Hinge

37.5” S40 Vertical Extrusion

37.5” S40 Vertical Extrusion w/ Door Hinge

15.48” Z45 Horizontal Extrusion

29.48” Z45 Horizontal Extrusion

33.917” Z45 Vertical Extrusion w/ Door Stops

Door

Hinge

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Connection

Shelf

Door

Shelf Support

Partial Assembly

Infill

Inf

Infill

Modied MOD-1550C Counter

Step 6 of 7

Order #XXXXX

Using Your Setup Instructions

The Aero Setup Instructions are created specifically for your configuration. The instructions include an

exploded view of the frame which is sequentially labeled. We encourage you to review the instructions

before attempting to assemble your exhibit.

Connections are kept very simple; no tools required. Everything assembles with push-button connectors.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Push-Button

Numbered Label

Connections are made by holding the button down and

sliding the red tube into opposing tube until button locks

into the hole. To disassemble, push button and pull or twist

extrusions apart.

Connect in alphabetical order as shown.

Aero Frame Assembly

Step 7 of 7

Order #XXXXX

Completed Assembly

10A

V4 Connector

Screw Cap

Graphic Frame

Vertical Extrusion

Slide V4 connector into groove of vertical

extrusion.Tighten set screw to secure V4

connector in place. Attach graphic frame to

connector, using screw cap. Tighten screw

cap to secure.

Graphic Frame Attachment

Align hole with pin Rotate pin. Spring

will push pin into hole.

Counter Top Lock

Hole

Shelf

Counter Top

Aero

Frame Aero

Frame

Graphic Frame Assembly

Item

9.9A

10,10A

Qty.

1,1

Description

15.28” TSP46 Curved Vertical

44.148” TSP46 Horizontal Extrusion

Steps:

1) Assemble graphic frame as shown.

2) Slide Aero frames into outer grooves of verticals [1] and [4].

3) Attach graphic frame to verticals [1] and [4]. See Graphic Frame Attachment detail.

4) Apply SEG graphics to graphic frame. See SEG Graphic Installation sheet for instruction.

5) Lock counter top to horizontals [5A]. See Counter Top Lock detail.

Shelf

Supports Shelf

Supports

Modied MOD-1550C Counter Cont’d

Classic Exhibits VK-1352 Setup Instructions

Classic Exhibits VK-1352 Setup Instructions

Classic Exhibits VK-1352 Setup Instructions

Related papers

Other documents