Toro Recycler Kit, Z334 Z Master Mower Installation guide
- Category
- Lawnmowers
- Type
- Installation guide
Form No. 3356-423 Rev A
Recycler® Kit
For Z334 Z Master® Mowers
Model No. 110-9960
Installation Instructions
Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.
Safety
Side Discharge or Mulch
Grass
W ithout the g rass deflector , discharge
co v er , or complete g rass catcher assembl y
mounted in place, y ou and other s ar e
exposed to blade contact and thr o wn de bris.
Contact with r otating mo w er blade(s) and
thr o wn de bris will cause injur y or death.
• Nev er r emo v e the g rass deflector fr om
the mo w er because the g rass deflector
r outes material do wn to w ard the turf.
If the g rass deflector is ev er dama ged,
r eplace it immediatel y .
• Nev er put y our hands or feet under the
mo w er .
• Nev er tr y to clear the discharge ar ea or
mo w er blades unless y ou disenga ge the
po w er tak e of f (PT O) lev er and tur n the
ignition k ey to of f. Also r emo v e the k ey
and pull the wir e of f the spar k plug(s).
Ensure the mo w er has the hing ed g rass deflector
that disperses clippings to the side and do wn
to w ard the turf , while in side disc harg e mode .
T o m ulc h g rass clippings , the baffles m ust be
installed into the mo w er as sho wn in the follo wing
ste ps .
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Register at www.Toro.com. Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Step
Description
Qty.
Use
1
No parts required
–
Prepare the mower.
2
No parts required
–
Remove the existing blades.
3
No parts required
–
Remove the existing bafes.
Discharge plate
1
Bolt (3/8 x 1 inch)
2
4
Flange nut (3/8 inch)
1
Install the discharge plate.
Left bafe
1
Right bafe
1
Angle support
1
Bolt (3/8 x 3/4 inch)
6
Flange nut (3/8 inch)
6
5
Bolt (3/8 x 1 inch)
2
Install the bafes.
6
Recycler blades
2
Install the new blades.
Step
1
Preparing the Mower
No Parts Required
Procedure
1. T horoughly clean mo w er dec k. All debris m ust
be remo v ed to ensure baffles will fit properly
ag ainst mo w er dec k.
2. R e pair all bent or damag ed areas of mo w er
dec k and re place any missing par ts .
Step
2
Removing the Existing
Blades
No Parts Required
Procedure
R emo v e the existing blades from the spindles
( Figure 1 ).
Note: Sa v e the blades for use when in side
disc harging mode . Use the blade bolt and cur v ed
w asher for installing the recycler blades .
A blade is shar p . Contact with shar p blade
can cause serious per sonal injur y .
W ear g lo v es or wrap shar p edges of the
blade with a ra g .
2
Figure 1
1. Sail area of blade 3. Curved washer
2. Blade 4. Blade bolt
Step
3
Removing the Existing
Bafes
No Parts Required
Procedure
Note: In the ste ps belo w , the bolts are threaded
into the mo w er dec k. R emo v e the n uts first before
remo ving bolts .
1. R emo v e the mo w er belt co v ers from the
mo w er dec k.
2. R emo v e the bolts , w ashers and flang e n uts
holding the front baffle in place ( Figure 2 ).
3. R emo v e the bolts and flang e n uts holding the
disc harg e baffle in place ( Figure 2 ).
Note: Sa v e the baffles and hardw are for use
when c hanging to side disc harging mode .
Figure 2
1. Bolt 4. Lock Nut
2. Mower deck 5. Discharge bafe
3. Front bafe
Step
4
Installing the Discharge
Plate
Parts needed for this step:
1
Discharge plate
2
Bolt (3/8 x 1 inch)
1
Flange nut (3/8 inch)
Procedure
Install the disc harg e plate to the outside of the
mounting brac k et with 2 bolts (3/8 x 1 inc h) and 2
flang e n uts (3/8 inc h) ( Figure 3 ).
Figure 3
1. Flange nut
(3/8 inch)
2. Mower
deck
3. Discharge
plate
4. Bolt (3/8 x
1 inch)
3
Step
5
Installing the Bafes
Parts needed for this step:
1
Left bafe
1
Right bafe
1
Angle support
6
Bolt (3/8 x 3/4 inch)
6
Flange nut (3/8 inch)
2
Bolt (3/8 x 1 inch)
Procedure
Note: All holes exist in the mo w er dec k for
installing the new baffles .
Note: Loosely install the baffles to align the
baffles with all existing holes in the mo w er .
1. Loosely install the angle suppor t to the left and
right baffles with 2 car riag e bolts (3/8 x 3/4
inc h) and 2 flang e n uts (3/8 inc h) ( Figure 4 ).
2. Loosely install the left and right baffle tog ether
with a car riag e bolt (3/8 x 3/4 inc h) and a
flang e n ut (3/8 inc h) ( Figure 4 ).
Figure 4
1. Flange nut (3/8 inch)
4. Angle support
2. Bolt (3/8 x 1 inch)
5. Right bafe
3. Left bafe
3. P osition the baffles into the mo w er .
4. Loosely install the baffles to the top of the
mo w er dec k with 2 bolts (3/8 x 1 inc h) ( Figure
5 ).
5. Loosely install the baffles to the disc harg e plate
with a bolt (3/8 x 3/4 inc h) and a flang e n ut
(3/8 inc h) ( Figure 5 ).
6. Loosely install the baffles to the side of the
mo w er dec k with a bolt (3/8 x 3/4 inc h) and a
flang e n ut (3/8 inc h) ( Figure 5 ).
7. Loosely install the baffles to the center of the
mo w er dec k with a bolt (3/8 x 3/4 inc h) and a
flang e n ut (3/8 inc h) ( Figure 5 ).
8. Tighten all fasteners .
Figure 5
1. Bolt (3/8 x 1 inch) 3. Flange nut (3/8 inch)
2. Bafes
4. Bolt (3/8 x 3/4 inch)
4
Step
6
Installing the New Blades
Parts needed for this step:
2
Recycler blades
Procedure
Important: T he sail par t of the blade (i.e.,
the tur ned up section) must f ace the inside of
the mo w er ( Figur e 6 ).
A blade is shar p . Contact with shar p blade
can cause serious per sonal injur y .
W ear g lo v es or wrap shar p edges of the
blade with a ra g .
1. Place the blade onto the spindle shaft ( Figure
6 ).
2. Install the spring disk and blade bolt. T he
spring disk cone m ust be installed to w ard the
bolt head ( Figure 6 ). T or que the blade bolt to
85-110 ft-lb (115-150 N•m).
Figure 6
1. Sail Area of Blade 4. Blade Bolt
2. Blade 5. Cone Towards Bolt Head
3. Spring Disk
3. Carefully rotate eac h blade to v erify there is a
1/16 inc h (1.6 mm) g ap betw een the end of
the blade and the baffles . If a blade contacts a
baffle , loosen the fasteners and position the
baffles to increase clearance betw een the end
of the blade and baffle .
4. Tighten the fasteners and c hec k for blade
clearance ag ain.
5
Operation
Selecting the Proper
Height-of-Cut
R emo v e appro ximately one inc h or no more
than 1/3 of the g rass blade when cutting . In
ex ce ptionally lush and dense g rass y ou ma y need
to raise the height-of-cut setting or con v er t to side
disc harg e or bag ging operations .
Mowing in Extreme
Conditions
Air is required to cut and recut g rass clippings in
the mo w er housing, so do not set the height-of-cut
too lo w or totally sur round the housing b y uncut
g rass . Alw a ys tr y to ha v e one side of the mo w er
housing free from uncut g rass , allo wing air to be
dra wn into the housing . W hen making an initial
cut through the center of an uncut area, operate
the mac hine slo w er and bac k up if the mo w er
star ts to clog .
Mowing at Proper Intervals
Under most nor mal conditions y ou will need to
mo w ev er y 4–5 da ys . Ho w ev er , g rass g ro ws at
different rates at different times . T hus , in order
to maintain the same height-of-cut, whic h is a
g ood practice , y ou’ll need to cut more frequently
in early spring; as the g rass g ro wth rate slo ws in
mid summer , cut only ev er y 8–10 da ys . If y ou
are unable to mo w for an extended period due to
w eather conditions or other reasons , con v er t to
side disc harg e or bag ging options or mo w first
with the height-of-cut at a high lev el; then mo w
ag ain 2–3 da ys later with a lo w er height setting .
Mowing with Sharp Blades
A shar p blade cuts cleanly and without tearing or
shredding the g rass . A dull blade will tear and
shred the g rass . T earing and shredding causes the
g rass to tur n bro wn at the edg es whic h impairs
g ro wth and increases susce ptibility to disease .
After Operating
T o ensure optim um perfor mance , clean the
underside of the mo w er housing after eac h use .
If residue is allo w ed to build up in the mo w er
housing, cutting perfor mance will decrease .
6
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Toro Recycler Kit, Z334 Z Master Mower Installation guide
- Category
- Lawnmowers
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Toro 52in Recycler Kit, TURBO FORCE Cutting Unit for Mid-Size Mowers Installation guide
-
-
-
-
-
-
-
Toro 42in Recycler Kit, TimeCutter Z4000/5000 Series Riding Mower Installation guide
-
-
Toro TimeCutter ZX525 Riding Mower User manual