ECHOGEAR EGLF2 Installation guide

Type
Installation guide

This manual is also suitable for

#YourGearUpgraded
INSTRUCTION MANUAL
Full Motion
TV Wall Mount
Model EGLF2
2
125 lbs.
(56.6 kg)
If your TV weighs more, this mount is NOT compatible.
Visit echogear.com to find a compatible mount.
Your TV (including accessories)
CANNOT EXCEED 125 lbs.
(56.6 kg) for this mount.
“You can think about it ...
but doooon’t do it.
IMPORTANT SAFETY INSTRUCTIONS. READ ENTIRE MANUAL PRIOR TO USE. SAVE These INSTRUCTIONS
Yea, the boring stuff ... but read it, so you don’t jack things up!
Weight Restrictions
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly
or use of this product, contact The Echogear Pros at 1-855-428-2490.
CAUTION: Avoid potential personal injuries and property damage!
This product is designed for use in wood stud, solid concrete, and concrete block walls -
DO NOT install into drywall alone
The wall must be capable of supporting five times the weight of the TV and mount combined
Do not use this product for any purpose not explicitly specified by manufacturer
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
CAUTION: DO NOT exceed
the maximum weight indicated. This
mounting system is intended for
use only with the maximum weights
indicated. Use with products
heavier than the maximum weights
indicated may result in collapse
of the mount and its accessories,
causing possible injury.
3
Solid concrete
or concrete
block?
Kit# CMK1
Required
(Not Included)
wood
studs (with
Drywall)?
Perfect!
Good to Go
CAUTION:
DO NOT
install into
drywall alone
Unsure?
Contact The Echogear Pros
at 1-855-428-2490 or
www.echogear.com
?
AwlStud Finder
7/32 in.
(5.5 mm)
for wood
Drill Bit
Socket
Wrench
HammerDrill Bit
3/8 in.
(10 mm)
for concrete
3/8 in.
(10 mm)
[1/4 in. Drive]
Wood Stud Wall Installation Concrete Wall Installation
Pencil Tape LevelPhillips
Screwdriver
Tape
Measure
Electric Drill
"Give it back
to Phil when
you finish"
Grab Your Tools
Verify Your Wall Construction
"The key
to minor
adjustments"
Hex Key
Toy Surprise
FREE Inside Every Box
UUUUHHH ?!?
HK
4
Echogear Satisfaction Guarantee:
One More Thing ...
We’re driven to give DIYers an awesome install experience. We stand
behind everything we make because you deserve the best entertainment
experience without sacrificing quality and spending your whole paycheck.
Guess what? We’ll help you through the entire process, too.
Why? Because we like to help and it’s our passion to provide authentic
service. We won’t leave you hanging, no matter what.
Our U.S. based Echogear Pros answer the phone in all days ending in Y.
That means availability to try and stump our expert sta 7 days a week.
Call us if you…
1
Have any questions before, during, or after install.
2
Need dierent hardware to fit your TV model.
3
Just need someone to chat with. We’re here for you.
5
WARNING: DON'T FEED TO CHILDREN
This product contains small items that could be a choking
hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are
missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
Never use damaged parts!
What’s in the Box
5/16 x 2¾ in.
5/16 in.
Fischer UX 10 x 60R
M8 x 25mm M8 x 50mm
M6 x 12mm
M8 x 16mm
M6 x 35mmM6 x 20mm
M8 x 35mm
2.5mm
22mm
M
6
/
M
8
M4 x 10mm
NOTE: Not all hardware included in this kit will be used.
STUFF FOR STEP 1
02
x4
03
x4
04
x4
05
x4
06
x4
07
x4
08
x4
09
x4
10
x8
11
x4
01 x2
TV Bracket
M6 TV Screws
M8 TV Screws
Washer
Spacers
6
5/16 x 2¾ in.
5/16 in.
Fischer UX 10 x 60R
M8 x 25mm M8 x 50mm
M6 x 12mm
M8 x 16mm
M6 x 35mmM6 x 20mm
M8 x 35mm
2.5mm
22mm
M
6
/
M
8
M4 x 10mm
STUFF FOR STEP 3
5/16 x 2¾ in.
5/16 in.
Fischer UX 10 x 60R
M8 x 25mm M8 x 50mm
M6 x 12mm
M8 x 16mm
M6 x 35mmM6 x 20mm
M8 x 35mm
2.5mm
22mm
M
6
/
M
8
M4 x 10mm
STUFF FOR STEP 2
Wall Plate/Arm
Drill Hole Template
Lag Screw
Concrete Anchor
Washer (For Lag Screw)
13 x1
12 x1
FOR CONCRETE INSTALLATIONS:
Call The Echogear Pros at 1-855-
428-2490 for concrete Kit# CMK1
End Cap
End Cap
Screw
16 x2
17 x4
14 x4
15 x4
x4
C1
7
STEP 1 Attach the TV BRACKETS TO YOUR TV
Select TV Screws
Select Spacers (if needed)
STEP 1.1 STEP 1.2
Only one screw size fits your TV.
M6
M8
"
Suggested uses for the extra screws
: board game pieces,
industrial jewelry, sweet corn holders, homemade maracas,
stocking stuers, currency (not most countries) ..."
a b
Long Screw
Short Screw
Washer
Washer
Spacer
Bracket
Bracket
EXTRA
SPACE
10
11
8
CAUTION: Ensure the TV brackets
01
are EQUALLY
CENTERED on your TV AND securely fastened in place.
Alternate
Spacer
setups
Secure the TV Brackets
STEP 1.3
a
Screw and washer
b
screw, washer and Spacer(s)
10
09
11
09
01
01
02 08
02 08
9
Max. 5/8 in. (16 mm)
CAUTION: Avoid potential personal injuries
and property damage!
Mount wall plate/arm
13
directly onto the
concrete surface (no surface covering).
CAUTION: Avoid potential personal injuries
and property damage!
Drywall covering the wall must not exceed 5/8 in.
(16 mm). Minimum wood stud size: nominal 2 x 4
in. (51 x 102 mm) actual 1½ x 3½ in. (38 x 89 mm).
STEP 2 Install the Wall Plate /Arm
Min.
8 in.
(203 mm)
Min.
8 in.
(203 mm)
Min.
8 in.
(203 mm)
Min.
16 in.
(406 mm)
Min. Wood Stud Spacing:
16 in. (406 mm)
Min. Wood Stud Width:
nominal 2 in. (51 mm)
actual 1 1/2 in. (38 mm)
Min. Wood Stud Depth:
nominal 4 in. (102 mm)
actual 3 1/2 in. (89 mm)
For
WOOD STUD INSTALLATIONS,
follow STEP 2A on PAGE 10
For
CONCRETE INSTALLATIONS,
follow STEP 2B on PAGE 12
10
(For Wood Stud)STEP 2A Install the Wall Plate /Arm
Use a stud
finder ...
... and/or verify
the edges with
an awl or a
small drill bit.
X-Ray
Specs
sold
separately
"favorite
pokey
device"
Align the Template
STEP 2A.2
"Come on ...
level with me"
Find a Stud
STEP 2A.1
TIP: Do this in
the location you are
installing wall plate
13
, so the holes will
be covered.
12
11
Install the Wall Plate /Arm
Drill Holes Secure Wall Plate
STEP 2A.3 STEP 2A.4
Go to STEP 3
on PAGE 14
CAUTION: Avoid potential personal injury or
property damage! All four lag screws
14
MUST BE
firmly tightened to prevent unwanted
movement of the wall plate assembly.
7/32 in.
(5.5 mm)
in. (6.9 cm)
Bit
13
14 15
12
12
(For CONCRETE)STEP 2B In stall the Wall Plate /Arm
Align the Template Drill Holes
STEP 2B.1 STEP 2B.2
"Come on ...
level with me"
002862.eps
IMPORTANT: Never drill into the mortar
between blocks.
3/8 in.
(10 mm)
3 in. (7.6 cm)
Bit
Min. hole Spacing:
24 in. (610 mm)
12
12
13
Insert Concrete Anchors Secure Wall Plate
STEP 2B.3 STEP 2B.4
For concrete anchors
C1
, contact The Echogear
Pros at 1-855-428-2490
CAUTION: Avoid potential personal injury or
property damage! All four lag screws
14
MUST BE
firmly tightened to prevent unwanted movement of
the wall plate assembly.
13
14 15
C1
12
14
STEP 3 Hang Your TV
Install End Caps Prepare Your TV
STEP 3.1 STEP 3.2
Save screws
S
for use in STEP 3.4
17
17
16
16
S
01
01
S
15
HEAVY! You may need
assistance with this step.
Hang Your TV
STEP 3.3
01
13
01
13
"SPAN THE FACEPLATE ...
that's a good name for a band!"
"Ask that friend of yours that
yammers on about crossfit"
IMPORTANT:
TV brackets
01
MUST
be centered
AND span the faceplate of arm
13
.
01
01
13
13
16
CAUTION: Avoid potential personal injury or property damage!
Bracket clips
B
and screws
S
MUST be installed to secure your
TV with brackets
01
to
wall plate/arm
13
.
Secure Your TV
STEP 3.4
01
01
13
S
B
13
17
ADJUSTMENTS
Tilt
1. Loosen the tilt lever
T
.
2. A
djust the TV tilt position.
3. Tighten tilt lever
T
to
secure the TV
in place at your desired tilt angle.
NOTE: If needed, tighten screw
T2
for additional tilt tensioning.
T
13
T2
HK
Righty
Tighty
Righty
Tighty
Lefty
Loosey
Lefty
Loosey
18
Level
1. Loosen the two screws
L
on the rear
of arm plate
13
,
using the hex key.
2. L
evel your TV.
3. Retighten screws
L
to secure in place.
L
13
Righty
Tighty
Lefty
Loosey
HK
19
REMOVE YOUR TV
Remove screws
S
and bracket clips
B
, then lift your TV up and off of
wall plate/arm
13
.
01
01
13
13
S
B
I'M
FREEEEE!!
HEAVY! You may need
assistance with this step.
"Don't be a hero!"
Lefty
Loosey
Confuzzled? Contact the ECHOGEAR Pros:
1-855-428-2490 helpmehelpy[email protected]om ECHOGEAR.com
Milestone Global Headquarters • 6436 City West Parkway • Eden Prairie, MN 55344 USA
“Wanna show o your hard work?
Share a picture of your completed project
with #YourGearUpgraded.
Who knows, it might not be as bad as you thought”
Milestone AV Technologies and its aliated corporations and subsidiaries (collectively, “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details,
conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of
this product. The information contained in this document is subject to change without notice or obligation of any kind.
Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone
assumes no responsibility for accuracy, completeness or suciency of the information contained in this document.
©2017 Milestone AV Technologies. All rights reserved. ECHOGEAR is a Milestone brand.
ECHOGEAR and the ECHOGEAR logo are trademarks of Milestone.
Made in China.
6901-602120 00
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

ECHOGEAR EGLF2 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI