ECHOGEAR EGGA-DMAC1 is a single monitor desk mount that provides a stable and ergonomic way to mount your monitor to your desk. With its adjustable arm, you can easily position your monitor to the perfect height, angle, and distance for comfortable viewing. The mount also features a built-in cable management system to keep your cables organized and out of sight.
Here are some of the key features and benefits of the ECHOGEAR EGGA-DMAC1:
- Supports monitors up to 35 lbs.
- Adjustable arm for optimal monitor positioning
- Built-in cable management system
- Easy to install
- Compatible with most monitors
ECHOGEAR EGGA-DMAC1 is a single monitor desk mount that provides a stable and ergonomic way to mount your monitor to your desk. With its adjustable arm, you can easily position your monitor to the perfect height, angle, and distance for comfortable viewing. The mount also features a built-in cable management system to keep your cables organized and out of sight.
Here are some of the key features and benefits of the ECHOGEAR EGGA-DMAC1:
- Supports monitors up to 35 lbs.
- Adjustable arm for optimal monitor positioning
- Built-in cable management system
- Easy to install
- Compatible with most monitors
#YourGearUpgraded
INSTRUCTION MANUAL
Model EGGA-DmAc1
Single Monitor
Desk Mount
2
WEIGHT RESTRICTIONS
For monitor (including accessories)
CANNOT EXCEED:
35 lbs.
(15.8 kg)
IMPORTANT SAFETY INSTRUCTIONS. READ ENTIRE MANUAL PRIOR TO quest. SAVE These INSTRUC
TIONS.
Before You EmBark on your Quest... just read it so you don’t get pwned!
Please read through these instructions completely and check your monitors' owner manual to see if there
are any special requirements for mounting your monitor.
If you do not understand these instructions, are a noob or have doubts about the safety of the
installation, assembly or use of this product, contact:
CAUTION: Manufacturer is not responsible for damage or injury caused by incorrect
assembly or use. To avoid any potential personal injuries, property damage or tipping:
► Your mounting surface must be stable and rugged enough to support the weight and motion of the
monitor and mount.
► Do not use this product for any purpose not explicitly specified by manufacturer.
“You even lift, Brah?....
Ok, even if you do... doooon’t do it.”
The Echogear Pros @ 1-855-428-2490 or www.echogear.com.
3
Contact The Echogear Pros:
1-855-428-2490
www.echogear.com
DESKTOP
THICKNESS
BFG
Yo Hands
Power up! Grab These Tools from Your arsenal
Size up Your Mounting Surface
Unsure?
?
UUUUHHH ?!?
Phillips
Screwdriver
Apple
Required to Get the Job Done
Optional Based on Skill Level
"No snapin
pics for
twitter
til you're
done!"
Hex Keys
BOnus Loot!
FREE Inside Every Box
⁄
M5
A
B
"
collect the
whole set"
Mini-Nuke
Pump
Refreshment
Saw
"Phil is
the boss"
0.8 in. — 2.6 in.
(20 mm — 66 mm)
4
We’re driven to give DIYers an awesome install experience. We stand
behind everything we make because you deserve the best entertainment
experience without sacrificing quality and spending your whole paycheck.
Guess what? We’ll help you through the entire process, too.
Why? Because we like to help and it’s our passion to provide authentic
service. We won’t leave you hanging, no matter what.
Our U.S. based Echogear Pros answer the phone in all days ending in Y.
That means availability to try and stump our expert sta 7 days a week.
Call us if you…
1
Have any questions before, during, or after install.
2
Need dierent hardware to fit your monitor model.
3
Just need someone to chat with. We’re here for you.
Echogear Satisfaction Guarantee:
ONE MORE THING ...
5
WARNINGS:
DON'T ALLOW CHILDREN TO FEED ON CONTENTS AND NEVER USE DAMAGED GOODS!
► This product contains small items that are a choking hazard if swallowed.
► Before you start assembly, verify all parts are included and undamaged. If any parts are missing
or damaged, do not return the damaged item to your dealer; contact Customer Service.
Here's your Loadout
GEAR FOR LEVEL 1
1
3
1 Desk Mount
1 Knob
(Clamp Screw)
1 Mount Cover
(Attached)
1 Clamp
4
2
6
Gear FOR Level 3
2 Cable
Straps
10
5
6
7
8
9
Gear FOR Level 2
4 Screws
M4 X 12mm
4 Spacers
2.5 mm
4 Screws
M4 X 30mm
4 Spacers
5 mm
4 Spacers
22 mm
7
1
STAGE 1: Insert Knob into Mount and Attach Clamp
Level 1
Lock It Down! Assemble Clamp and Mount to Desk
3
4
"You spin me right round, baby
right round like a record, baby
right round round round...and
round and round and round..."
4
3
8
STAGE 2: Secure Clamp to Surface
1
b
a
"...and round and round
and round and round."
A
USE HEX KEY
A
TO SECURELY
CLAMP IT DOWN.
A
9
1
STAGE 3: Adjust Arm to Desired Height
TIP: ADJUST THE
ARM HEIGHT BEFORE
MONITOR IS ATTACHED.
OTHERWISE IT'S A TWO
PERSON JOB.
B
"Lefty"
"Righty"
to TIGHTEN
tension
B
B
to LOOSEN
tension
b
a
c
10
Level 2
Make The DROP! Attach Monitor to Mount
Select
Spacers
(if needed)
Flat Monitor
NEEDED FOR
NOT NEEDED
or
Select
Screws
Bracket
Short Screw
5
Spacer
Long Screw
Bracket
7/ 8 / 9
6
or
STAGE 1: Determine Screw Length and Spacer Size
Round
Monitor
Inset
Holes
Cables
Flat
Monitor
+
11
STAGE 2:
Partially Insert Top Screws into Monitor
6
5
OR
Stack as
needed
7/ 8 / 9
12
1
STAGE 3: Hang Your Monitor with the Top Screws
13
STAGE 4:
Insert Bottom Screws and Tighten All Four Screws
1
IMPORTANT: YOU SHOULD TEST THE TENSION
OF THE ROTATING BRACKET
R
TO ASSURE
THE MONITOR MOVES WITH EASE AND STAYS IN
POSITION BEFORE TIGHTENING ALL SCREWS.
SEE PAGE 18 TO ADJUST BRACKETS TENSION.
"Batten
down the
hatches"
R
6
5
OR
Stack as
needed
7/ 8 / 9
14
Level 3
Control the Melee!
STAGE 1: Route Cables and Attach with Straps
+2
1
IMPORTANT: LEAVE
ENOUGH SLACK IN THE
CABLES TO ASSURE THE
MONITOR AND ARMS
MOVE WITH EASE.
10
10
15
STAGE 2:
Snap in Plastic Sheet
1+
to Disguise Cables
"U R A BOSS"
"Time to post some pics
of your battlestation.
Don't forget to add:
#YourGearUpgraded"
2
1
a
c
b
Top View
16
Vertical Position - Adjust Mounting Bar Up and Down
"Lefty"
Bonus Level! Adjustments /Modifiers
"Righty"
to TIGHTEN
tension
B
B
to LOOSEN
tension
b
a
c
17
Horizontal Position - Adjust Monitors Left or Right
WARNING:
MONITOR MUST REMAIN OVER DESK SURFACE.
Top View
Desk
Desk
18
Tilt & Level - Tilt and Turn Monitor 360
0
IF MONITOR DOES NOT MOVE WITH EASE OR WILL NOT LOCK INTO DESIRED POSTION:
Remove the monitor. Turn the screw
D
on the tension bracket either
counter-clockwise (loosen) or clockwise (tighten)
D
.
Repeat as needed.
D
WARNING:
MONITOR MUST REMAIN OVER DESK SURFACE.
"Come on ...
level with me..."
19
1. Remove Cables
2. Remove Monitor
3. Remove Mount
How to remove Mount from Monitor and Surface
OR
A
Confuzzled? Contact the ECHOGEAR Pros:
1-855-428-2490 helpmehelpy[email protected]om ECHOGEAR.com
Legrand AV Inc. • 6436 City West Parkway • Eden Prairie, MN 55344 USA
“Wanna show o your skillzz?
Share a picture of your completed mount
with #YourGearUpgraded.
Who knows, it might not be as bad as you thought”
©2019 Legrand AV Inc. All Rights Reserved. ECHOGEAR is a Legrand AV Inc. brand and a registered trademark owned by Legrand.
Legrand AV Inc. and its aliated corporations and subsidiaries (collectively, “Legrand”), intend to make this manual
accurate and complete. However, Legrand makes no claim that the information contained herein covers all details,
conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of
this product. The information contained in this document is subject to change without notice or obligation of any kind.
Legrand makes no representation of warranty, expressed or implied, regarding the information contained herein. Legrand
assumes no responsibility for accuracy, completeness or suciency of the information contained in this document.
6901-602305 00
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
ECHOGEAR EGGA-DMAC1 User manual
- Type
- User manual
- This manual is also suitable for
ECHOGEAR EGGA-DMAC1 is a single monitor desk mount that provides a stable and ergonomic way to mount your monitor to your desk. With its adjustable arm, you can easily position your monitor to the perfect height, angle, and distance for comfortable viewing. The mount also features a built-in cable management system to keep your cables organized and out of sight.
Here are some of the key features and benefits of the ECHOGEAR EGGA-DMAC1:
- Supports monitors up to 35 lbs.
- Adjustable arm for optimal monitor positioning
- Built-in cable management system
- Easy to install
- Compatible with most monitors
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ECHOGEAR EGAV-ASUC82 Owner's manual
-
ECHOGEAR EGAV-ASBC62 User guide
-
ECHOGEAR EGAV-RTVF3 User manual
-
-
-
-
-
-
-
Other documents
-
HUANUO HNMUA1 Installation guide
-
Sanus BEHHS Installation guide
-
Bauhn AMAB-0619-S User manual
-
-
Bauhn ADMAB-0222 Installation guide
-
-
-
HPM LSQ103KBL User manual
-
HPM LWK0110WBL User manual
-
Sanus WSSCAM1-B2 User manual
