Altronix T2HNK7F8 Installation guide

T2HNK7F8

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with THN2 Altronix/Honeywell NetAXS backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Fused Power Distribution Module

Rev. 040819

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

All components of this Trove kit are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Access & Power Integration

- 2 - T2HNK7F8 Installation Guide

Overview:

Altronix T2HNK7F8 Trove Honeywell NetAXS kit is pre-assembled and consists of Trove2HN2 enclosure/backplane with factory installed Altronix

power supply/charger and sub-assemblies. T2HNK7F8 kit also accommodates various combinations of Honeywell NetAXS boards for up to eight

(8) doors in a single enclosure.

THN2 accommodates a combination of the following Honeywell NetAXS boards:

• Up to two (2) NX4PCB access control panels.

• Up to four (4) NetAXS-123 access control panels.

• Up to four (4) NXD1 or NXD2 add-on boards to NetAXS-123.

• Up to four (4) NX4IN or NX4OUT boards.

Configuration Chart:

Altronix

Model Number

Power Supply Board

Input Fuse Rating

Power Supply Board

Battery Fuse Rating

120VAC 60Hz

Input Current (A)

Maximum Supply

Current for Main and

Aux. Outputs on

Power Supply board

and ACM8 Access

Power Controllers’

outputs

Nominal DC Output

Voltage

Fail-Safe/Fail-Secure

or Dry Form “C”

Outputs

Additional Fused

Outputs

ACM8 Board

Input Fuse Rating

ACM8 Board

Output Fuse Rating

PDS8 Board

Input Fuse Rating

PDS8 Board

Output Fuse Rating

[DC] [Aux]

Output

Range

(VDC)

Output

Range

(VDC)

T2HNK7F8 6.3A/

250V

15A/

32V 4.5 24VDC @ 9.7A 20.17-26.4 20.28-26.4 8 8 10A/

250V

2.5A/

250V

10A/

32V

3A/

32V

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having juris-

diction. Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners

and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper

screws, level and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and

install the three fasteners. Place the enclosure’s upper keyholes over the three upper screws. Install the three lower

screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent)

in desired location, opposite hinge. Slide the tamper switch bracket onto the edge

of the enclosure, approximately 2” from the right side (Fig. 1, pg. 2).

Connect tamper switch wiring to the Access Control Panel input or the

appropriate UL Listed reporting device. To activate alarm signal

open the door of the enclosure.

4. Mount Honeywell NetAXS boards to THN2 backplane, refer to pages 3-5.

5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow104NB

and corresponding Sub-Assembly Installation Guides for the following models:

ACM8, PDS8 and VR6 for further installation instructions.

Hardware:

Fig. 1

Tamper Switch

(included)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Nylon Spacer | 5/16” Pan Head Screw | Lock Nut

T2HNK7F8 Installation Guide - 3 -

Pem

Spacer

Honeywell

Access Controller

Backplane

Pan Head

Screw

Fig. 2a

Altronix - eFlow104NB

– DC +– BAT +

L G N

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4 5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

ON

1 2 3 4

ON

Altronix - ACM8

+ INP1 --

PWR1 +OFF

IN1

IN2

Out1

<1 off 2>

PWR1 +

PWR2 +

COM ---

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

N

P

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

10

3

3333 33

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

Altronix - PDS8

Altronix VR6 is mounted under PDS8

RJ45 Jack

Honeywell - NX4PCB

RJ45 Jack

Honeywell - NX4PCB

Fig. 2

Configuration of Honeywell NX4PCB Boards:

1. Align Honeywell NX4PCB boards on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 2a, pg. 3).

3. Mount Honeywell NX4PCB boards to spacers utilizing pan head screws (provided) (Fig. 2a, pg. 3).

Note: Honeywell NX4PCB boards have one (1) RJ45 jack and one (1) switch each.

Please make sure that they are mounted correctly, as shown in Fig. 2 below.

4. Fasten THN2 backplane to Trove2 enclosure utilizing hardware (provided).

- 4 - T2HNK7F8 Installation Guide

Pem

Spacer

Honeywell

Access Controller

Backplane

Pan Head

Screw

Spacer

Bottom of NetAXS-123

Bottom of

NXD1/NXD2

Pre-installed

Bump Screw

Mounting

Hole

Fig. 3a

Fig. 3b

Altronix - eFlow104NB

– DC +– BAT +

L G N

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4 5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

ON

1 2 3 4

ON

Altronix - ACM8

+ INP1 --

PWR1 +

OFF

IN1

IN2

Out1

<1 off 2>

PWR2 +PWR2 +

COM --

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

N

P

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

10

3

3333 33

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

Altronix - PDS8

Altronix VR6 is mounted under PDS8

RJ45 Jack

Honeywell NetAXS-123

Honeywell

NXD1 or NXD2

RJ45 Jack

Honeywell NetAXS-123

Honeywell

NXD1 or NXD2

RJ45 Jack

Honeywell NetAXS-123

Honeywell

NXD1 or NXD2

RJ45 Jack

Honeywell NetAXS-123

Honeywell

NXD1 or NXD2

Fig. 3

Configuration of Honeywell NetAXS-123 with or without NXD1/NXD2 Boards:

1. Align Honeywell NetAXS-123 boards on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 3a, pg. 4).

3. Mount Honeywell NetAXS-123 boards to spacers utilizing pan head screws (provided) (Fig. 3a, pg. 4).

Note: Honeywell NetAXS-123 boards have one (1) RJ45 jack.

Please make sure that they are mounted correctly, as shown in Fig. 3 below.

In order to properly mount and connect NXD1/NXD2 do the following:

- prior to mounting on backplane, attach NXD1/NXD2 to the NetAXS-123 by connecting the multi-pin connector on the

bottom of NXD1/NXD2 to the multi-pin jack on NetAXS-123. Make sure that pre-installed bump screws on NXD1/

NXD2 go through the corresponding holes in NetAXS-123.

- secure NXD1/NXD2 to NetAXS-123 using pre-installed bump screws and included spacers (Fig. 3b, pg. 4).

- after NXD1/NXD2 is firmly attached and connected to NetAXS-123, follow steps 1 and 2 above to mount them onto THN2.

4. Fasten THN2 backplane to Trove2 enclosure utilizing hardware (provided).

T2HNK7F8 Installation Guide - 5 -

Altronix - eFlow104NB

– DC +– BAT +

L G N

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4 5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

ON

1 2 3 4

ON

Altronix - ACM8

+ INP1 --

PWR1 +

OFF

IN1

IN2

Out1

<1 off 2>

PWR2 +PWR2 +

COM ---

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

N

P

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

10

3

3333 33

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

Altronix - PDS8

Altronix VR6 is mounted under PDS8

Honeywell - NX4IN or NX4OUT

Fig. 4

Configuration of Honeywell NX4IN or NX4OUT Boards:

1. Align Honeywell NX4IN or NX4OUT boards on the backplane to match the boards’ mounting holes with

corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 4a, pg. 5).

3. Mount Honeywell NX4IN or NX4OUT boards to spacers utilizing pan head screws (provided) (Fig. 4a, pg. 5).

4. Fasten THN2 backplane to Trove2 enclosure utilizing hardware (provided).

Pem

Spacer

Honeywell

Access Controller

Backplane

Pan Head

Screw

Fig. 4a

- 6 - T2HNK7F8 Installation Guide

Notes:

T2HNK7F8 Installation Guide - 7 -

eFlow Power Supply/Chargers can be Controlled and Monitored while

Reporting Power/Diagnostics from Anywhere over the Network...

LINQ2 Mounts Inside any Trove Enclosure

LINQ2 - Network Communication Module

LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep systems up

and running at optimal levels. It facilitates fast and easy installation and set-up, minimizes system downtime,

and eliminates unnecessary service calls, which helps reduce Total Cost of Ownership (TCO) - as well as creat-

ing a new source of Recurring Monthly Revenue (RMR).

LINQ2

Features:

- UL Listed in the U.S. and Canada.

- Local or remote control of up to (2) two Altronix eFlow power output(s) via LAN and/or WAN.

- Monitor real time diagnostics: DC output voltage, output current, AC & battery status/service, input trigger state change,

output state change and unit temperature.

- Access control and user managment: Restrict read/write, Restrict users to speciﬁc resources

- Two (2) integral network controlled Form “C” Relays.

- Three (3) programmable input triggers: Control relays and power supplies via external hardware sources.

- Email and Windows Dashboard notiﬁcations

- Event log tracks history.

- Secure Socket Layer (SSL).

- Programmable via USB or web browser - includes operating software and 6 ft. USB cable.

LINQ2 Module

Altronix eFlow

Power Supply

Network Connection:

Installation, Programming

and Monitoring

- 8 - T2HNK7F8 Installation Guide

Enclosure Dimensions (H x W x D approximate):

27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm)

6.75” (171.5mm)8.25” (209.5mm)

8.00” (203.2mm)

2.00” (50.8mm)

1.25” (31.8mm)

5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)

1.25” (31.8mm)

6.25” (158.8mm) 19.80” (502.9mm)

1.00” (25.4mm)

27” (685.8mm)

1.5”

(38.1mm)

2.00” (50.8mm) 2.00” (50.8mm)

3.5”(88.9mm) 3.5”(88.9mm)

21.50” (546.1mm)

5.25” (133.35mm) 5.25” (133.35mm)

6.25” (158.8mm)

1.25”

(31.8mm)

0.85” (21.6mm)

0.5625” (14.3mm)

2.415” (61.3mm)

0.685” (17.4mm)

1.77”

(45mm)

0.885” (22.5mm)

1.125” (28.3mm)

Knockouts

2.00” (50.8mm) 2.00” (50.8mm)

Altronix is not responsible for any typographical errors.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056

web site: www.altronix.com | e-mail: [email protected] | Lifetime Warranty

IIT2HNK7F8 I27U

MEMBER