Midmark International (Whip) Delivery Installation guide

Brand: Midmark

Model: International (Whip) Delivery

Type: Installation guide

This manual is also suitable for

Asepsis 21® Systems

Midmark International (Whip) Delivery system enhances your dental operatory with a versatile, reliable, and efficient solution for delivering dental instruments and materials. This innovative system streamlines your workflow, maximizing productivity and patient satisfaction.

NOTES

• This plan may be placed on the floor in the de-

sired location and then used as a template for

punching center holes.

• The locations shown in this plan are suggestions

and are not meant to be restrictive in any way.

They may be altered to fit the situation or suit the

doctor’s preferences.

• If so equipped, the APC may be removed for

J-box and umbilical installation.

• The electrical and plumbing supply connectors in-

side the J-Box (Junction Box) must be installed by

an electrician and plumber in compliance with lo-

cal building codes.

• Midmark Corporation assumes no responsibility

for failure due to improper installation.

CAUTIONS

• Water and air valves to be located as to be readily

accessible for emergency shut-off. DO NOT

LOCATE VALVES UNDER APC UNIT if so

equipped.

• Be sure that connection box location DOES NOT

INTERFERE WITH CHAIR MOVEMENT.

• Water pressure to be a minimum of 30 PSI (207

Kpa) but NOT TO EXCEED 50 PSI (345 Kpa)

MAXIMUM.

• Air pressure to be 80 PSIG (552 Kpa) and NOT

TO EXCEED 100 PSIG (689 Kpa) MAXIMUM.

1" (2.5 cm)

(max.)

3/4" (1.9 cm)

(min.)

AIR and

WATER

VACUUM

WASTE

FINISHED FLOOR LEVEL

1/2"

(1.3 cm)

16" (40.6 cm)

Recommended Location

from Center of Chair

Rotation

1" (2.5 cm)

(max.)

3/4" (1.9 cm)

(min.)

Compression

Fitting Valve

Installation

Instructions

For a Large or Small Junction

Box on Knight Units

UTILITY SPECIFICATIONS

WATER

1/2" pipe terminating with a 1/2" pipe up 3/4" (1.9 cm) to 1" (2.5 cm) from

the finished surface as near to the connection box as possible.

Flush all debris from the lines before installation.

Water pressure to be a minimum 30 psi (207 kPa) and not to exceed a

maximum 50 psi (345 kPa).

AIR

1/2" pipe terminating with a 1/2" pipe up 3/4" (1.9 cm) to 1" (2.5 cm) from

the finished surface as near to the connection box as possible.

Flush all debris from the lines before installation.

Air pressure to be minimum 80 PSIG (552 kPa) and not to exceed a

maximum 100 PSIG (689 Kpa).

For maximum life of unit, air supply must be clean and dry.

It is recommended that a moisture separator and filter be installed as near

to the connection box as possible and be accessible for periodic cleaning.

ELECTRICAL SUPPLY

Three (3) conductor #14 AWG cable on a 15 amp fused circuit to terminate

inside a 4" (10.1 cm) x 4" (10.1 cm) jiffy box (not supplied) in location

shown.

If installing 115 VAC receptacle:

A right angle power plug is supplied.

If installing a 230 VAC receptacle:

An appropriate style power plug rated for 250 VAC, 15 amps (not supplied)

is required .

VACUUM

Terminate with 5/8" OD tube 3/4" (1.9 cm) to 1" ( 2.5 cm) above the

finished floor.

Install line according to vacuum system manufacturer’s specifications.

AUXILIARY WIRING

Low voltage.

“For class 2 circuits only”.

Install in compliance with all prevailing codes.

WASTE

Required for the Gravity Drain Cuspidor.

Not less than 1 1/2" ID pipe from down pipe to trap decreasing to 3/4" pipe

from trap to connection box.

Terminate with 3/4" O.D. pipe 3/4" (1.9 cm) to 1" (2.5 cm) above finish floor.

Install trap in line and vent to conform with local codes.

003-1190-01 Rev.F (8/12)

Midmark Corporation

60 Vista Drive

P.O. Box 286

Versailles, Ohio 45380-0286

1-800-MIDMARK

Fax 877-249-1793

midmark.com

ELECTRICAL

BOX

4" x 4"

BOX FOR

POWER

SUPPLY

(not

supplied)

AIR

WATER

VACUUM

WASTE

TUBING FOR

OPTIONS

UMBILICAL

FOOT CONTROL

TUBING INLET AIR

(5/16" Clear w/

Black Dash)

1/8" RED TUBE

PILOT AIR

MASTER VALVE

1/8" PURPLE TUBE

NON-CONTROLLED

AIR MASTER VALVE

1/4" BLUE TUBE

CUSPIDOR

(Optional)

1/8" ORANGE TUBE

COOLANT WATER

PILOT AIR

1/4" or 5/16"

CLEAR TUBE

DRIVE AIR OUT

1/8" YELLOW TUBE

FOR SYRINGE AIR

1/8" YELLOW or

WHITE TUBE

(Tagged w/ "C")

FOR CUSPIDOR

(Optional)

1/8" BROWN TUBE

AIR TO DISTILLED

WATER BOTTLE

1/8" BROWN TUBE

1/8" RED TUBE

Blue

Green

Clear

White

AIR REGULATOR

FOR DISTILLED

WATER BOTTLE

1/4" CLEAR TUBE

FOR AIR QUICK

CONNECT (Optional)

5/16" CLEAR TUBE

(

w/ BLACK DASH

)

TO FOOT CONTROL

TO FOOT

CONTROL

5/16"

CLEAR

TUBE

Air

Regulator

5/16" Clear

80 PSI

1/8 Yellow

PSI

1/8 Orange

To Handpiece Coolant Air (1/8 Green)

Clear

Throttle

Valve

Wet / Dry

Toggle

5/16" Clear

(w/ Black Dash)

1/8

Yellow

To Pilot Air for Coolant Water (1/8 Orange)

1/8 Green

Air to Syringe & Cuspidor

Filter / Regulated Air

80 PSI

PSI

Foot Control

Clear

1/8 Orange

5/16" Clear

To Handpiece Drive Air

(5/16" Clear)

1/8 Green

1/8

Green

5/16"

Clear

1/8 OR

1/8

5/16"

Clear

w/ Dash

1/8

(Chip Air)

1/4 Grey (Plain)

1/4 Clear

80 PSI

To Handpiece Drive Air (1/4 Clear)

1/8 Yellow

PSI

1/8 Orange

To Handpiece Coolant Air (1/8 Green)

Clear

1/8 Grey

Throttle

Valve

Wet / Dry

Toggle

Tubing

Layout

1/8 Grey (above 1/4 ribbed)

1/4 Grey (Ribbed)

1/8

Yellow

To Pilot Air for Coolant Water (1/8 Orange)

1/8 Green

Air to Syringe & Cuspidor

Filter / Regulated Air

Air

Regulator

80 PSI

PSI

(Rib)

Foot Control

1/8 Grey

Clear

WATER

AIR

WATER

OUT IN

1/4" BLUE TUBE / CUSPIDOR WATER

UNFILTERED AND UNREGULATED (OPTIONAL)

1/8" RED TUBE

PILOT AIR

MASTER VALVE

SMALL JUNCTION BOX

(with Regulators)

NOTICE: These tubing

connections are required

only if the unit installed is

so equipped.

UMBILICAL

1/8" ORANGE TUBE

COOLANT WATER

PILOT AIR

1/4" CLEAR TUBE

DRIVE AIR OUT

VACUUM

WASTE

1/4" YELLOW TUBE

ASST WATER

(OPTIONAL)

1/8" BROWN TUBE

CUSPIDOR

PILOT AIR

(OPTIONAL)

1/8" BLUE TUBE

COOLANT AND

SYRINGE WATER

FOOT CONTROL INLET

(TUBE w/ RIB)

1/8" YELLOW TUBE

SYRINGE AIR

1/8" PURPLE TUBE

NON-CONTROLLED AIR

MASTER VALVE

AIR

WATER

OUT IN

UMBILICAL

1/8" ORANGE TUBE

COOLANT WATER

PILOT AIR

1/4" CLEAR TUBE

DRIVE AIR OUT

1/4" YELLOW TUBE

DRIVE AIR IN

VACUUM WASTE

POWER UMBILICAL

(SUPPLIED WITH J-BOX)

1/4" BLUE TUBE

WATER

3/8" BLACK TUBE

AIR SUPPLY

3/8" BLACK TUBE

WATER SUPPLY

(SUPPLIED WITH

J-BOX)

WATER SHUT OFF VALVE

1/8" RED TUBE

PILOT AIR

POWER SUPPLY

CABLE

SMALL JUNCTION BOX

(without Regulators)

NOTICE: These tubing

connections are required

only if the unit installed is

so equipped.

Midmark International (Whip) Delivery Installation guide

Brand: Midmark

Model: International (Whip) Delivery

Type: Installation guide

This manual is also suitable for

Asepsis 21® Systems

Download PDF

report

Midmark International (Whip) Delivery Installation guide

This manual is also suitable for

Midmark International (Whip) Delivery Installation guide

Related papers

Other documents