SignaMax 065-7700 User guide

Signamax Connectivity Systems

Hardened Managed PoE Ethernet Switch

Model -065-7700

U

SER

’

S

G

UIDE

Hardened Managed PoE Ethernet Switch

User’s Manual 1

Quick Start Guide

This quick start guide describes how to install and use the

Hardened Managed PoE (Power over Ethernet) Ethernet

Switch. This is the switch of choice for harsh environments

constrained by space.

Physical Description

The Port Status LEDs and Power Inputs

Hardened Managed PoE Ethernet Switch

User’s Manual 2

LED State Indication

10/100BaseTX

LINK/ACT

Steady A valid network connection established.

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

PoE

Steady Power Device (PD) is connected.

Off Power Device (PD) is disconnected.

10/100BaseTX, 100BaseFX/BX SFP

LINK/ACT

Steady A valid network connection established.

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

10/100/1000BaseTX, 1000BaseSX/LX/BX SFP

LINK/ACT

Steady A valid network connection established.

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Power Input Assignment

Power3

47-57VDC

DC Jack

Power2

＋

47-57VDC

Terminal

Block

－

Power Ground

Power1

＋

47-57VDC

－

Power Ground

Earth Ground

Relay Output Rating

1A @ 250VAC

Relay Alarm Assignment

Hardened Managed PoE Ethernet Switch

User’s Manual 3

FAULT

*Warning signal disable for following:

1. The relay contact closes if Power1 and

Power2 are both failed but Power3 on.

2. The relay contact closes if Power3 is failed

but Power1 and Power2 are both on.

Functional Description

 Meets NEMA TS1/TS2 Environmental requirements such as

temperature, shock, and vibration for traffic control equipment.

 Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity

for industrial environment.

 RS-232 console, Telnet, SNMP v1 & v2c & v3, RMON, Web Browser,

and TFTP management.

 Supports Command Line Interface in RS-232 console.

 Supports 8192 MAC addresses. Provides 2M bits memory buffer.

 Port 1 ~ Port 4 support IEEE802.3at Power over Ethernet (PoE) Power

Sourcing Equipment (PSE) and/or Port 5 ~ Port 8 support IEEE802.3af

Power over Ethernet (PoE) Power Sourcing Equipment (PSE).

 Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation,

1000Mbps-full-duplex, 10/100Mbps-full/half-duplex, Auto MDI/MDIX.

 100BaseFX: Multi mode or Single mode duplex LC type. 100BaseBX:

WDM Multi mode or Single mode single LC type.

 1000BaseSX/LX: Multi mode or Single mode duplex LC type.

1000BaseBX: WDM Multi mode or Single mode single LC type.

 Store-and-forward mechanism. Full wire-speed forwarding rate.

 Alarms for power and port link failure by relay output.

 Power Supply: Redundant 47-57VDC Terminal Block power inputs or

47-57VDC DC Jack power input.

 Field Wiring Terminal: Use Copper Conductors Only, 60/75℃, 12-24

AWG torque value 7 lb-in.

 Operating voltage and Max. current consumption: 0.31A @ 48VDC.

Power consumption: Power consumption: 230W Max. (Full load with

PoE), 15W Max. (Without PoE).

 -40℃ to 75℃ (-40℉ to 167℉) operating temperature range. Tested for

functional operation @ -40℃ to 85℃ (-40℉ to 185℉). UL508

Hardened Managed PoE Ethernet Switch

User’s Manual 4

Industrial Control Equipment certified Maximum Surrounding Air

Temperature @ 75℃ (167℉).

 For use in Pollution Degree 2 Environment.

 Hardened metal case.

 Supports Din-Rail or Panel Mounting installation.

Hardened Managed PoE Ethernet Switch

User’s Manual 5

Console Configuration

 Connect to the switch console:

Connect the DB9 straight cable to the RS-232 serial port of the device

and the RS-232 serial port of the terminal or computer running the

terminal emulation application. Direct access to the administration

console is achieved by directly connecting a terminal or a PC equipped

with a terminal-emulation program (such as HyperTerminal) to the

switch console port.

 Configuration settings of the terminal-emulation program:

Baud rate: 115,200bps

Data bits: 8

Parity: none

Stop bit: 1

Flow control: none

 Press the “Enter” key. The Command Line Interface (CLI) screen should

appear as below:

 Logon to Exec Mode (View Mode):

At the “switch_a login:” prompt just type in “root” and press <Enter> to

logon to Exec Mode (or View Mode). And the “switch_a>” prompt will

show on the screen.

Hardened Managed PoE Ethernet Switch

User’s Manual 6

 Logon to Privileged Exec Mode (Enable Mode):

At the “switch_a>” prompt just type in “enable” and press <Enter> to

logon to Privileged Exec Mode (or Enable Mode). And the “switch_a#”

prompt will show on the screen.

 Logon to Configure Mode (Configure Terminal Mode):

At the “switch_a#” prompt just type in “configure terminal” and press

<Enter> to logon to Configure Mode (or Configure Terminal Mode). And

the “switch_a(config)#” prompt will show on the screen.

 Set new IP address and subnet mask for Switch:

At the “switch_a(config)#” prompt just type in “interface vlan1.1” and

press <Enter> to logon to vlan 1 (vlan1.1 means vlan 1). And the

“switch_a(config-if)#” prompt will show on the screen.

Command Syntax: “ip address A.B.C.D/M”. “A.B.C.D” specifies IP

address. “M” specifies IP subnet mask. “M”= 8: 255.0.0.0,

16:255.255.0.0, or 24: 255.255.255.0.

For example, At the “switch_a(config-if)#” prompt just type in “ip address

192.168.1.10/24” and press <Enter> to set new IP address

(192.168.1.10) and new IP subnet mask (255.255.255.0) for Switch.

Hardened Managed PoE Ethernet Switch

User’s Manual 7

Web Configuration

 Login the switch:

Specify the default IP address (192.168.1.10) of the switch in the web

browser. A login window will be shown as below:

Hardened Managed PoE Ethernet Switch

User’s Manual 8

 Enter the factory default login ID: root.

Enter the factory default password (no password).

Then click on the “Login” button to log on to the switch.

Hardened Managed PoE Ethernet Switch

User’s Manual 9

Hardened Managed PoE Ethernet Switch

User’s Manual 10

Preface

This manual describes how to install and use the Signamax

Hardened Managed PoE (Power over Ethernet) Ethernet

Switch. This switch introduced here is designed to deliver full

scalability with SNMP/RMON web-based management

functions by providing:

To get the most out of this manual, you should have an

understanding of Ethernet networking concepts.

In this manual, you will find:

 Features on the Hardened Managed PoE Ethernet Switch

 Illustrative LED functions

 Installation instructions

 Management Configuration

 SNMP, IGMP…

 Specifications

Hardened Managed PoE Ethernet Switch

User’s Manual 11

Table of Contents

Quick Start Guide 1

PHYSICAL DESCRIPTION 1

The Port Status LEDs and Power Inputs 1

FUNCTIONAL DESCRIPTION 3

CONSOLE CONFIGURATION 5

WEB CONFIGURATION 7

Preface 10

Table of Contents 11

Product Overview 13

HARDENED MANAGED POE ETHERNET SWITCH 13

PACKAGE CONTENTS 13

PRODUCT HIGHLIGHTS 15

Basic Features 15

Management Support 16

FRONT PANEL DISPLAY 17

PHYSICAL PORTS 18

SWITCH MANAGEMENT 19

Web-based browser interface 19

Administration console via RS-232 serial port (CLI) 19

External SNMP-based network management application 19

Installation 20

SELECTING A SITE FOR THE SWITCH 20

WIRING DIAGRAM 20

DIN RAIL MOUNTING 21

CONNECTING TO POWER 22

47-57VDC Jack 22

Redundant 47-57VDC DC Terminal Block Power Input 22

Alarms for Power Failure 23

CONNECTING TO YOUR NETWORK 24

Cable Type & Length 24

Cabling 25

Switch Management 26

MANAGEMENT ACCESS OVERVIEW 26

ADMINISTRATION CONSOLE (CLI) 27

Direct Access 27

Modem Access 28

WEB MANAGEMENT 28

SNMP-BASED NETWORK MANAGEMENT 28

PROTOCOLS 29

MANAGEMENT ARCHITECTURE 29

Hardened Managed PoE Ethernet Switch

User’s Manual 12

Web-Based Browser Management 30

SNMP & RMON Management 31

OVERVIEW 31

SNMP AGENT AND MIB-2 (RFC 1213) 32

RMON MIB (RFC 2819) AND BRIDGE MIB (RFC 1493) 32

RMON Groups Supported 33

Bridge Groups Supported 33

Web-Based Browser Management 34

LOGGING ON TO THE SWITCH 34

UNDERSTANDING THE BROWSER INTERFACE 36

SYSTEM 38

PORT 52

SWITCHING 58

TRUNKING 64

STP / RING 65

VLAN 75

QOS 82

SNMP 85

802.1X 90

OTHER PROTOCOLS 94

Command Line Console Management 100

ADMINISTRATION CONSOLE 100

Exec Mode (View Mode) 101

Privileged Exec Mode (Enable Mode) 105

Configure Mode (Configure Terminal Mode) 110

SYSTEM 114

PORT 124

SWITCHING 129

TRUNKING 138

STP / RING 139

VLAN 153

QOS 159

SNMP 162

802.1X 171

OTHER PROTOCOLS 176

Specifications 188

Appendix A 190

Appendix B 191

Contact Information 198

Hardened Managed PoE Ethernet Switch

User’s Manual 13

Product Overview

Hardened Managed PoE Ethernet Switch

Front View

Package Contents

When you unpack the product package, you shall find the

items listed below. Please inspect the contents, and report

any apparent damage or missing items immediately to your

authorized reseller.

•

This Switch

Hardened Managed PoE Ethernet Switch

User’s Manual 14

• User’s Manual

• RS-232 cable

Hardened Managed PoE Ethernet Switch

User’s Manual 15

Product Highlights

Basic Features

 Meets NEMA TS1/TS2 Environmental requirements such as

temperature, shock, and vibration for traffic control equipment.

 Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity

for industrial environment.

 RS-232 console, Telnet, SNMP v1 & v2c & v3, RMON, Web Browser,

and TFTP management.

 Supports Command Line Interface in RS-232 console.

 Supports 8192 MAC addresses. Provides 2M bits memory buffer.

 Port 1 ~ Port 4 support IEEE802.3at Power over Ethernet (PoE) Power

Sourcing Equipment (PSE) and/or Port 5 ~ Port 8 support IEEE802.3af

Power over Ethernet (PoE) Power Sourcing Equipment (PSE).

 Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation,

1000Mbps-full-duplex, 10/100Mbps-full/half-duplex, Auto MDI/MDIX.

 100BaseFX: Multi mode or Single mode duplex LC type. 100BaseBX:

WDM Multi mode or Single mode single LC type.

 1000BaseSX/LX: Multi mode or Single mode duplex LC type.

1000BaseBX: WDM Multi mode or Single mode single LC type.

 Store-and-forward mechanism. Full wire-speed forwarding rate.

 Alarms for power and port link failure by relay output.

 Power Supply: Redundant 47-57VDC Terminal Block power inputs or

47-57VDC DC Jack power input.

 Field Wiring Terminal: Use Copper Conductors Only, 60/75℃, 12-24

AWG torque value 7 lb-in.

 Operating voltage and Max. current consumption: 0.31A @ 48VDC.

Power consumption: Power consumption: 230W Max. (Full load with

PoE), 15W Max. (Without PoE).

 -40℃ to 75℃ (-40℉ to 167℉) operating temperature range. Tested for

functional operation @ -40℃ to 85℃ (-40℉ to 185℉). UL508

Industrial Control Equipment certified Maximum Surrounding Air

Temperature @ 75℃ (167℉).

 For use in Pollution Degree 2 Environment.

Hardened Managed PoE Ethernet Switch

User’s Manual 16

 Hardened metal case.

 Supports Din-Rail or Panel Mounting installation.

Management Support

VLAN

 Port-based VLAN

 IEEE802.1Q tagged VLAN

TRUNKING

 Port Trunking

PORT-SECURITY

 Per-port programmable MAC address locking

 Up to 24 Static Secure MAC addresses per port

 IEEE802.1x Port-based Network Access Control

PORT-MIRRORING

 Port-mirroring

QOS (IEEE802.1p Quality of Service)

 4 priority queues

INTERNETWORKING PROTOCOLS

 Bridging:

IEEE802.1s Multiple Spanning Tree

IEEE802.1w Rapid Spanning Tree

IEEE802.1D Spanning Tree compatible

IEEE802.1Q – GVRP

Ring

 IP Multicast:

IGMP Snooping

 Rate Control

 NTP

NETWORK MANAGEMENT METHODS

 Console port access via RS-232 cable (CLI, Command Line Interface)

 Telnet remote access

 SNMP agent:

MIB-2 (RFC1213)

Bridge MIB (RFC1493)

RMON MIB (RFC2819) – statistics, history, alarm and events

VLAN MIB (IEEE802.1Q/RFC2674)

Private MIB

 Web browser

 TFTP software-upgrade capability

Hardened Managed PoE Ethernet Switch

User’s Manual 17

Front Panel Display

 POWER

This LED comes on when the switch is properly connected to power and

turned on.

 P ort Sta tus LEDs

The LEDs are located on the front panel, displaying status for each

respective port. Please refer to the following table for more details.

LED State Indication

10/100BaseTX

LINK/ACT

Steady A valid network connection established.

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

PoE

Steady Power Device (PD) is connected.

Off Power Device (PD) is disconnected.

Hardened Managed PoE Ethernet Switch

User’s Manual 18

10/100BaseTX, 100BaseFX/BX SFP

LINK/ACT

Steady A valid network connection established.

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

10/100/1000BaseTX, 1000BaseSX/LX/BX SFP

LINK/ACT

Steady A valid network connection established.

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Physical Ports

The Hardened Managed Ethernet Switch provides:

Number of ports

10/100Base-TX (802.3at)

4

10/100Base-TX (802.3af)

0, 4

100Base SFP:

10/100Base-TX

100Base-FX/BX

2

1000Base SFP:

10/100/1000Base-TX

1000Base-SX/LX/BX

2

CONNECTIVITY



RJ-45 connectors on TX ports

 Single or Duplex LC connectors on SFP 100BaseFX/BX

fiber transceiver

 Single or Duplex LC connectors on SFP

1000BaseSX/LX/BX fiber transceiver

MODE SELECTION



10BaseT full-duplex mode

 10BaseT half-duplex mode

 100BaseTX full-duplex mode

 100BaseTX half-duplex mode

 100BaseFX full-duplex mode

 1000BaseT/SX/LX full-duplex mode

 Auto-negotiating mode

Hardened Managed PoE Ethernet Switch

User’s Manual 19

Switch Management

Web-based browser interface

The switch also boasts a point-and-click browser-based interface that

lets user access full switch configuration and functionality from a

Netscape or Internet Explorer browser.

Administration console via RS-232 serial port (CLI)

The switch provides an onboard serial port, which allows the switch to be

configured via a directly connected terminal.

External SNMP-based network management

application

The switch can also be configured via SNMP.

Page is loading ...

SignaMax 065-7700, 10/100 Managed Industrial PoE Switches, 10/100 Managed Industrial PoE+ Switches User guide

Related papers

Other documents