U.S.Robotics BROADBAND ROUTER - QUICK REV 1.1 User manual

Wireless MAXg Router and

Wireless MAXg USB Adapter

Quick Installation Guide

Guide d'installation rapide

Installationsanleitung

Guida all'installazione rapida

Guía breve de instalación

Beknopte installatiegids

R24.0555.00

rev 1.1 10/05

Page is loading ...

Installing the Router and Wireless USB Adapter ..................... 1

Installation du routeur et du Wireless USB Adapter .............. 13

Installieren des Routers und des Wireless USB Adapters ..... 25

Installazione di Router e USB Adapter ................................... 37

Instalación del Wireless USB Adapter y del Router ...............49

De Router en de Wireless USB Adapter installeren ............... 61

Page is loading ...

1

Installing the Router and Wireless USB Adapter

Package Contents:

Prepare for installation

You must have administrator rights on your computer in order to install this product.

You will need to install this Installation CD-ROM on all the PCs on which you plan to install

Wireless MAXg USB Adapters.

To use the Wireless MAXg Adapter, you must be using Windows XP (Service Pack 1 or higher) or

2000 (Service Pack 4 or higher).

For the most updated information, visit: http://www.usr.com/support

You can also refer to the User Guides on the U.S. Robotics Installation CD-ROM for more detailed

information.

Step One: Connect the Wireless MAXg Router

A. Turn off your computer and your cable or DSL modem.

Disconnect the modem’s Ethernet cable from your

computer and connect it to the WAN port of the Wireless

MAXg Router.

B. Connect the supplied Ethernet cable to the Network Interface Card of your computer and to

one of the LAN ports of the Wireless MAXg Router.

C. Connect the antenna to the Wireless MAXg Router.

D. Connect the power adapter to the Wireless MAXg Router and to a standard wall power

outlet. Turn on your computer.

USR5461 Wireless MAXg Router Installation CD-ROM which includes User Guides

USR5421 Wireless MAXg USB Adapter 5VDC power supply

Quick Installation Guide Detachable antenna

One (1) Ethernet cable

2

E. Turn on your cable or DSL modem.

Note to UK Users: Attach the correct power plug to the power adapter.

Note: You have finished connecting the Wireless MAXg Router and will now need to install

the Wireless MAXg USB Adapter.

Step Two: Install the Wireless MAXg USB Adapter

A. Insert the USB Adapter Installation CD-ROM into the CD-ROM drive of the computer you are

installing the USB Adapter in. The Installation CD Graphical User Interface (GUI) will appear

on your screen. If prompted, select your preferred language.

Note: If your CD-ROM does not automatically launch, click Windows Start, Run, type

D:\setup (if your CD-ROM drive uses a different letter, type that letter in place of “D”), and

click OK.

B. Click Installation.

C. Follow the on-screen instructions.

D. When prompted, locate an available USB port and

fully insert the Wireless MAXg USB Adapter.

Windows XP users should follow any on-screen

instructions.

E. When prompted, click Restart to restart your computer.

Note: You may see a screen which says “Digital Signature Not Found” or “Windows Logo

testing”. Click Yes or Continue Anyway. U.S. Robotics has thoroughly tested this product’s

driver in conjunction with the supported hardware and has verified compatibility with

Windows XP and 2000. Because U.S. Robotics wants its customers to take full advantage

of the network card’s functionality, it has made the drivers available.

3

Step Three: Set up a Wireless Network

A. When your computer restarts and you are prompted, select Configure a new U.S. Robotics

Wireless MAXg Router and click Next. You will need to wait while the Wireless MAXg USB

Adapter communicates with the router.

B. If prompted, select your Internet Connection type and click Next. Depending on the type of

Internet Connection that you choose, you may need to enter some additional information.

C. Enter a Network name and a Pass phrase (also known as network key) for your wireless

encryption and click Next. You will need to wait while the router and the USB Adapter are

configured.

Note: U.S. Robotics recommends that you enable WPA security so that your wireless

network is secure. Make sure you assign the same secret WPA key to all your wireless

devices to ensure network connectivity. For more information about this and additional

wireless parameters, refer to the User Guides on the U.S. Robotics Installation CD-ROM.

D. When prompted, enter a User name and Password for the router login and then click Next.

Wait while the configuration continues.

E. You will then see a screen that shows you the settings for your Wireless MAXg Router. These

settings will be saved to a text file on your computer desktop and you have the option to

print them out if your computer is connected to a printer. When you are done reviewing this

information, click Finish. Your Wireless MAXg Router and USB Adapter should all be

configured and ready for use.

Congratulations! You have finished installing your product. The Wireless MAXg USB Adapter

should now be connected to the network that you set up.

If you experience any problems connecting to a wireless networking device, refer to the

Troubleshooting section in this guide or to the Configuration section of the Wireless MAXg

Adapter User Guide on the U.S. Robotics Installation CD-ROM for more information.

4

Opening the Configuration Utility

You should now see a small icon for the Configuration Utility in the system tray by your clock on

your computer desktop. You can open the Configuration Utility in two ways:

• Right-click the icon and click Open Utility.

• Left-click once on the Utility icon to open the quick connect screen. In the quick connect

screen, you can select an available network and enter the Network key, if applicable. Click

Connect to establish a wireless connection. You can also click Advanced to open the full

Configuration Utility.

The Configuration Utility is used to change or verify the configuration information that relates to

your Wireless MAXg USB Adapter. The Configuration Utility icon will be colored to indicate the

status of your wireless network: red for disconnected and green for connected with good quality.

USB Printer Installation

A USB printer can be connected to the Wireless MAXg Router and used as a network printer if you

are using an operating system that supports printing to an Internet Printing Protocol (IPP)-based

printer. Windows XP and 2000 have built-in support for this function, but other Windows users

will need to download either a Microsoft patch for their version of Windows or a third party

application. Refer to the documentation for your version of Windows for more information. Other

operating systems will need to either already support IPP-based printing or download a third

party application for their operating system.

Perform the following steps to install and set up the printer.

Step One: Connect the printer to the Wireless MAXg Router

Plug the square end of a USB cable into the USB port on your printer. Plug the thin rectangular

end of the USB cable into the USB port on the Wireless MAXg Router. Connect the power supply

to your printer and turn your printer on.

Step Two: Set up your printer

Launch a Web browser. In the browser’s location or address line, type http://192.168.2.1 to

access the Web User Interface.

Look on the Status page for the Printer Status and Printer location information in the Device

section. Write down the Printer location information since this is the network address of the

printer and you will need this to set up the printer.

5

Perform the following steps to set up your printer. You will need to do this on every computer that

is connected to your network and wants to be able to access the printer.

1. Windows XP Users: Click Windows Start and then Printers and Faxes.

Windows 2000, Me, and 98 Users: Click Windows Start, Settings, and then Printers.

2. Click Add Printer and the Add Printer Wizard will launch. Click Next.

3. Select Network printer and click Next.

4. Select Connect to a printer on the Internet... and enter the network address listed in Printer

location. Click Next.

Note: The network address that is listed in Printer location must be entered exactly

as it is seen on-screen. The address field is case-sensitive. If the network address is

not entered correctly, the printer will not be located.

5. You will be prompted to choose the brand and model of your printer. You can either select

them from the list or click Have Disk, insert the CD-ROM that came with your printer, and

navigate to your CD-ROM drive to locate the drivers. When you are finished, click Next.

6. When prompted, select Yes or No to set this printer as your default printer. If prompted, you

can choose to print a test page.

7. You will be shown the information regarding your printer. Click Finish to complete the setup

process.

Step Three: Verify the printer connection

If you look on the Status page of the Web User Interface, your printer status should now be listed

as "Ready". You can verify the printer is working correctly by clicking the Print this page link in

the Help area on the right side of the screen. If this prints correctly, your printer setup is

complete.

If the printer status is listed as "Not Ready", make sure the printer is turned on and that the USB

cable is firmly connected to both the printer and to the Wireless MAXg Router.

If the printer status is still listed as "Not Ready" or if the page did not print correctly, repeat the

setup procedure and make sure you enter all the correct information.

Register your Wireless MAXg Router and Wireless

MAXg USB Adapter

Register your products online at http://www.usr.com/productreg

6

Troubleshooting

I am no longer able to access the Internet.

When your computer connects to the Internet, a number of devices have to work together.

A. Your computer connects to your Wireless MAXg Router via a wireless or wired connection.

B. Your Wireless MAXg Router connects to your broadband cable/DSL modem via an Ethernet

cable.

C. Your cable/DSL modem connects to your Internet Service Provider (ISP) via your cable/

phone network.

The first step in solving this problem is to diagnose the cause. There are a number of places

where the connection from your computer to the Internet might fail.

First, check the indicator lights of your various devices. If one or more of these devices indicate a

problem, it’s a good indication of where you should focus your troubleshooting efforts.

1. If your computer uses a wireless connection to your router, does the wireless utility indicate

there is a good connection to your router?

If your computer cannot communicate with the router, it cannot access the Internet.

2. Are your Wireless MAXg Router’s power, wireless, and Internet LEDs lighted?

If the router is turned off, or the wireless radio isn’t operating, or it has no connection to the

Internet (via your cable/DSL modem), your computer won’t be able to access the Internet

either.

3. Do your cable/DSL modem’s power and status LEDs indicate a connection? (Please refer to

your modem’s documentation for information on its status indicators.)

If your modem is turned off or cannot communicate with your ISP, your router will be unable

to access the Internet.

Now, let’s step through the various devices and determine which one isn’t connecting properly.

Step 1: Can your computer connect to your Wireless MAXg Router?

If you use a wired connection:

If you use a wired connection between your computer and your Wireless MAXg Router, ensure the

Ethernet cable is connected to your computer’s LAN port and to a LAN port on the router, and also

that the corresponding LEDs are lighted.

If you use a wireless connection:

If you have a wireless connection to your Wireless MAXg Router, does your wireless utility report

a successful connection to your router?

If your wireless utility reports a successful wireless connection, it’s possible that your computer

has connected to a neighbor’s router instead of yours. You can use your wireless utility to check

the network name (SSID) of the router you’re connected to. If it’s connected to the wrong router,

you can use the utility to force your computer to try to connect to your router.

7

If you do not have a connection to your Wireless MAXg Router, you can try the following solutions:

1 Ensure that your computer is close enough to your router to receive a signal and that there

is nothing interfering with the signal, such as a microwave oven or a concrete wall. If your

router broadcasts its network name, you can use your computer’s wireless utility to scan for

it. (This is typically called a “site survey.”) If your utility can’t detect your router, it may be a

signal problem.

2. Ensure that the wireless utility is using the correct network name and security settings for

your router. Settings such as network name, security method (WPA, WEP, etc.), and security

keys must all match. If your router is using WPA encryption, each wireless card or adapter

must support WPA encryption. Please refer to the Configuration section of the Wireless

MAXg Router User Guide for information on changing the security settings.

3. If you have enabled MAC filtering, is this computer permitted to connect to your router?

Please note that MAC filtering refers to specific wireless adapters. If you use MAC filtering

and you’ve changed wireless adapters, you will have to add the MAC address of the new

wireless adapter to the router.

You’ve probably noticed that you need to access your Wireless MAXg Router in order to check

some of these things. We’ll do that in the next step.

If none of these work, you can try a wired connection between your computer and your router by

connecting an Ethernet cable between your computer’s LAN port and a LAN port on the router.

(Ensure that the corresponding LAN port LEDs are lighted.) If a wired connection works, the

problem is almost certainly with your computer’s wireless connection to the router. You should

then try the previous steps again.

Step 2: Is your Wireless MAXg Router responding?

If you have a wireless or wired connection to your Wireless MAXg Router, open your Web browser

to the router’s address: 192.168.2.1 (Please note that if you’ve modified the router’s LAN IP

address, you should use the new one.)

If the Wireless MAXg Router’s Web interface doesn’t appear, your computer may need to re-

establish a connection to your router:

Release and renew your computer’s network connection.

Windows XP, 2000, and NT users:

Press Start and select Run.

Type cmd and press ENTER.

Type ipconfig /release and press ENTER.

Type ipconfig /renew and press ENTER.

Type exit and press ENTER.

Windows Me, 98, and 95 users:

Press Start and select Run.

Enter winipcfg and press ENTER.

Click Release.

Click Renew.

Close the application.

Your computer should acquire an IP address (such as 192.168.2.5) from the router.

Try to access the router’s Web address at http://192.168.2.1

If the Wireless MAXg Router’s Web interface doesn’t appear, the router may need to be restarted:

1. With a thin tool, such as a paper clip, briefly press the RESET button on the back of the

router. Hold it in for 1 to 2 seconds to reset the Router. If you press the RESET button for

more than five seconds, the router will return to its factory default settings.

8

2. Wait about 30 seconds.

3. Release and renew your computer’s network connection. (See above for details.)

4. Try to access the router’s Web address at http://192.168.2.1

If you still cannot access the Wireless MAXg Router, the router may need to be restored to the

default factory settings. (Please note that you will lose all of your router’s custom settings and

will need to set it up again as if you were installing it for the first time. Alternatively, if you’ve

made a backup of the settings, you will be able to restore them. See the Wireless MAXg Router’s

User’s Guide on the installation CD-ROM for more information on backups.)

1. With a thin tool, such as a paper clip, press the RESET button on the back of the router for at

least five seconds.

2. Wait about 30 seconds.

3. Try to access the router’s Web address at http://192.168.2.1

If the Wireless MAXg Router’s Web interface still doesn’t appear, it’s possible that the router has

failed. Please contact U.S. Robotics Customer Support.

If the Wireless MAXg Router’s Web interface appears, the problem may be with its connection to

your cable/DSL modem.

Step 3: Can your Wireless MAXg Router connect to your cable/DSL modem?

Now that you have accessed your Wireless MAXg Router’s Web interface, go to the Status page.

There should be a statement at the top of the page (below the Status tab) indicating whether the

router is connected to the Internet.

Sample screenshot of a router connected to the Internet:

Sample screenshot of a router not connected to the Internet:

You can confirm that statement by checking the Status page’s WAN section to see if the router

has a WAN IP address (such as 235.42.181.5). This IP address indicates whether the router is

connected to the cable/DSL modem.

9

If the router doesn’t have a WAN IP address, select the router’s Internet page and use it to

configure the router’s Internet connection. (If you have a DSL modem, you may be required to

enter the login information your ISP provided.)

If the Wireless MAXg Router still cannot obtain a WAN IP address, it is likely there is a problem

with the cable/DSL modem or your ISP.

Step 4: Can your cable/DSL modem connect to your ISP?

If your computer has a connection to your Wireless MAXg Router and the router’s Internet

connection is configured correctly, but the router cannot connect to the Internet, it’s possible that

the cable/DSL modem has lost its connection or isn’t functioning properly, or there’s a problem

with your ISP.

1. Ensure that an Ethernet cable is connected between your router’s WAN port and the cable/

DSL modem’s Ethernet port and that the corresponding LEDs are lighted.

2. Ensure that your cable/DSL modem is connected to your wall jack. (A cable modem uses a

coax cable, and a DSL modem uses an RJ-11 cable.)

3. Restart the cable/DSL modem. (There may be a power switch or reset button on the modem,

or you may have to unplug/re-plug the modem’s power adapter. Consult your modem’s

documentation.)

4. After the cable/DSL modem has restarted and connected to your ISP, click the Reboot

button on your router’s Device page.

5. After the router has finished rebooting, click Continue to return to the Status page.

If your Wireless MAXg Router now says it’s connected to the Internet and has a WAN IP address,

try to access the Internet. If you still cannot access the Internet, please start at the beginning of

this troubleshooting procedure to determine the new point of failure. (It’s possible that your

wireless connection needs to be re-established.)

If the Wireless MAXg Router still does not have a WAN IP address, the problem may be with the

cable/DSL modem or your ISP. Please contact your ISP’s Customer Support.

10

I accidentally clicked Cancel during the software installation procedure for the

Wireless MAXg USB Adapter.

Possible Solution:

Remove and reinsert the Installation CD-ROM into your CD-ROM drive. Follow the instructions in

this guide for installing the software.

The U.S Robotics interface did not begin when I inserted the Installation CD-ROM.

Possible Solution:

Some programs may disable the autorun feature of Windows. Close any open applications and

reinsert the Installation CD-ROM. If the Installation CD-ROM interface does not run automatically,

click Windows Start and then click Run. In the “Run” dialog box, type D:\setup.exe. If your CD-

ROM drive uses a different letter, type that letter in place of “D.”

I inserted the Wireless MAXg USB Adapter before the Installation CD-ROM.

Possible Solution:

If you inserted the Wireless MAXg USB Adapter before the Installation CD-ROM, cancel the

installation procedure that is currently running. Insert the Installation CD-ROM, select your

language, click Installation, and then follow the on-screen instructions.

For more troubleshooting information or for advanced wireless configuration options, refer to the

Wireless MAXG USB Adapter User Guide on the Installation CD-ROM or go to www.usr.com/

support

The Setup Wizard was unable to detect my Internet connection.

Possible Solution:

You will need to manually configure your Internet connection. There are two methods of

instructions you can follow to setup your Internet connection: If you are still in the Setup Wizard

or If you have already closed the Setup Wizard.

If you are still in the Setup Wizard:

Select your Internet connection type: either Cable, DSL Router, satellite, ISN, LAN, or other or

DSL modem (also known as PPPoE). Depending on your selection, you will need to enter some

information that was provided by your ISP. After entering all of your necessary information,

click Next. Continue to follow the on-screen instructions to complete the Setup Wizard. For

more information about the settings, refer to the Web User Interface section of the Wireless

MAXg Router User Guide on the Installation CD-ROM.

If you have already closed the Setup Wizard:

Launch a Web browser. In the location or address line of your Web browser, type

http://192.168.2.1 to access the Web User Interface. Click the Internet tab. Select your

Internet connection type: either Cable, DSL Router, satellite, ISN, LAN, or other or DSL

modem (also known as PPPoE). Depending on your selection, you will need to enter some

information that was provided by your ISP. When you are finished, click Save. You should now

be able to access the Internet. For more information about the settings, refer to the Web User

Interface section of the Wireless MAXg Router User Guide on the Installation CD-ROM.

11

My Wireless MAXg Router’s Web User Interface is not responding, but I can still

access the Internet.

Possible Solution:

If your Web User Interface stops responding, unplug and then plug back in the power supply of

the Wireless MAXg Router. This will reboot the Wireless MAXg Router. If you are still unable to

use the Web User Interface, press in and hold the RESET button for five to ten seconds. This will

reset the Wireless MAXg Router to the factory default settings. If you made any personal

configuration settings, you will need to make the changes again or restore your settings if you

created a backup file. (See the Wireless MAXg Router’s User Guide on the installation CD-ROM for

more information.)

My computer does not recognise the Wireless MAXg USB Adapter.

Possible Solution:

The Wireless MAXg USB Adapter may not be fully inserted into the USB port. You can also try

installing the Wireless MAXg USB Adapter into a different USB port.

I am unable to communicate with the Wireless MAXg Router.

Possible Solution:

Be sure that each Wireless MAXg USB Adapter that you want to connect to the wireless network is

set to Infrastructure mode within the Configuration Utility. If your Wireless MAXg USB Adapters

are not set to Infrastructure mode, they will not be able to communicate with an Access Point or

Wireless Router.

Possible Solution:

Determine the MAC address of the router. Using the U.S. Robotics Configuration utility, check the

MAC address and verify that you are connecting to the correct Wireless MAXg Router.

Possible Solution:

Ensure that the Configuration Utility is installed for your Wireless MAXg USB Adapter and that the

Configuration Utility detects your Wireless MAXg USB Adapter.

Possible Solution:

Ensure that the correct Authentication Mode and encryption key are being used. If you changed

the settings in the configuration of your Wireless MAXg Router, you must also change the settings

of every Wireless MAXg USB Adapter attached to this network to match. If you are still

experiencing difficulties, reset all of your Wireless Routers or Access Points and wireless network

adapters to the default settings and try again.

I am experiencing poor wireless link quality.

Possible Solution:

Low link quality or range can be caused by environmental interference, such as lead-based paint

and concrete walls. Try to move the antenna of the Wireless MAXg Router or to reposition the

wireless clients to improve the link quality.

12

Possible Solution:

Some electronic items, such as 2.4Ghz phones, may interfere with the wireless signal and affect

your wireless range and link quality. Try creating a wireless connection on a different channel.

Refer to the Configuration section of the Wireless MAXg Router User Guide on the Installation

CD-ROM for more information on changing your wireless settings.

Additional Support

Note: Your model numbers are 5461 (for the MAXg Wireless Router) and 5421 (for the MAXg Wireless

USB Adapter). You can find your serial number on the label of the product and on the side of the

package. Write your serial numbers down. If you ever need to call our Technical Support department,

you will need them to receive assistance.

1. Go to the User Guides on the Installation CD-ROM.

More configuration and advanced troubleshooting information is available in the Wireless MAXg Router and

USB Adapter User Guides on the Installation CD-ROM.

2. Go to the Support section of the U.S Robotics Web site at www.usr.com

Many of the most common difficulties users experience have been addressed in the FAQ and

Troubleshooting Web pages for your specific product.

3. Submit your technical support question using an online form at http://www.usr.com/emailsupport

4. Call the U.S. Robotics Technical Support department.

Country Voice Online Support Hours

United States & Canada (888) 216-2850 http://www.usr.com/emailsupport 9:00 A.M. - 5:00 P.M., M-F CST

Austria 07 110 900 116 http://www.usr.com/emailsupport/de 9:00 –17:00, M-F

Belgium (Flemish) +32 (0)70 233 545 http://www.usr.com/emailsupport/ea 9:00 –17:00, M-F

Belgium (French) +32 (0)70 233 546 http://www.usr.com/emailsupport/ea 9:00 –17:00, M-F

Denmark +45 7010 4030 http://www.usr.com/emailsupport/uk 9:00 –17:00, M-F

Finland +358 98 171 0015 http://www.usr.com/emailsupport/ea 9:00 –17:00, M-F

France 082 507 0693 http://www.usr.com/emailsupport/fr 9:00 –17:00, M-F

Germany 01805671548 http://www.usr.com/emailsupport/de 9:00 –17:00, M-F

Hungary 01805671548 http://www.usr.com/emailsupport/hu 9:00 –17:00, M-F

Ireland +44 870 844 4546 http://www.usr.com/emailsupport/uk 9:00 –17:00, M-F

Italy 848 80 9903 http://www.usr.com/emailsupport/it 9:00 –17:00, M-F

Luxembourg +352 342 080 8318 http://www.usr.com/emailsupport/bn 9:00 –17:00, M-F

Middle East/Africa +44 870 844 4546 http://www.usr.com/emailsupport/me 9:00 –17:00, M-F

Netherlands 0900 20 25 857 http://www.usr.com/emailsupport/ea 9:00 –17:00, M-F

Norway +47 23 50 0097 http://www.usr.com/emailsupport/ea 9:00 –17:00, M-F

Poland http://www.usr.com/emailsupport/pl

Portugal +351 (0)21 415 4034 http://www.usr.com/emailsupport/pt 9:00 –17:00, M-F

Spain 902 117 964 http://www.usr.com/emailsupport/es 9:00 –17:00, M-F

Sweden +46 (0) 77 128 1020 http://www.usr.com/emailsupport/ea 9:00 –17:00, M-F

Switzerland +0848 840 200 http://www.usr.com/emailsupport/de 9:00 –17:00, M-F

UK 0870 844 4546 http://www.usr.com/emailsupport/uk 9:00 –17:00, M-F

For current support contact information, go to the following Web site: http://www.usr.com/support

Regulatory and warranty information are located in the User Guides on the Installation CD-ROM.

Model Number Serial Number

USR5461

USR5421

Page is loading ...

Printed in XXXXXX.

U.S.Robotics BROADBAND ROUTER - QUICK REV 1.1 User manual

This manual is also suitable for

U.S.Robotics BROADBAND ROUTER - QUICK REV 1.1 User manual

in other languages

Related papers

Other documents