H3C SR6600 SPE-FWM Card Manual

H3C
Brand
H3C
Model
SR6600 SPE-FWM
Type
Card Manual

This manual is also suitable for

H3C SR6600 SPE-FWM is a versatile and powerful security appliance that provides a comprehensive suite of network security features to protect your network from a wide range of threats.

With its high-performance hardware and advanced software, the H3C SR6600 SPE-FWM can handle even the most demanding network traffic, making it ideal for use in large enterprises and data centers. Some of the key features of the H3C SR6600 SPE-FWM include:

Stateful firewall: The H3C SR6600 SPE-FWM's stateful firewall inspects all incoming and outgoing traffic and blocks any packets that do not match the defined security rules. This helps to protect your network from unauthorized access, Denial of Service (DoS) attacks, and other threats.

H3C SR6600 SPE-FWM is a versatile and powerful security appliance that provides a comprehensive suite of network security features to protect your network from a wide range of threats.

With its high-performance hardware and advanced software, the H3C SR6600 SPE-FWM can handle even the most demanding network traffic, making it ideal for use in large enterprises and data centers. Some of the key features of the H3C SR6600 SPE-FWM include:

Stateful firewall: The H3C SR6600 SPE-FWM's stateful firewall inspects all incoming and outgoing traffic and blocks any packets that do not match the defined security rules. This helps to protect your network from unauthorized access, Denial of Service (DoS) attacks, and other threats.

Manual version: T2-082324-20141219-C-1.02 BOM: 3123A124
i
H3C S9500 LSB1FW2A0 Card Manual
1 Card identifier
The card identifier LSB1FW2A0 is at the upper right corner of the front panel.
2 Introduction
The LSB1FW2A0 module provides one console port, one CF card slot, two USB interfaces, two
10/100/1000BASE-T management Ethernet electrical interfaces, and two management Gigabit combo
interfaces.
You can use a GE port or combo interface to provide the following functions:
• In-band management.
• Outgoing interface for log messages.
• Failover interface for stateful failover.
3 Specifications
Figure 1 Front panel
(1) CF card eject button (2)
CF card slot
(CF CARD)
(3) CF LED (CFS)
(4) Console port (CONSOLE) (5) USB interface 1 (reserved) (6) USB interface 2 (reserved)
(7) Management Ethernet interface 1
(10/100/1000BASE-T)
(8) Management Ethernet interface
2
(10/100/1000BASE-T)
(9) Management Ethernet
interface 1 LED (LINK)
(10) Management Ethernet interface 1
LED (ACT)
(11) Management Ethernet interface
2
LED (LINK)
(12) Management Ethernet
interface 2 LED (ACT)
(13) Management interface 3
(Electrical port of combo interface
10/100/1000BASE-T)
(14) Management interface 4
(Electrical port of combo interface
10/100/1000BASE-T)
(15) Management interface 3
(Optical port of combo
interface 1000BASE-X)
(16) Management interface 4 (Optical
port of combo interface 1000BASE-X)
(17) Management interface 3 LED
(LINK)
(18) Management interface 3
LED (ACT)
(19) Management interface 4 LED
(LINK)
(20) Management interface 4 LED
(ACT)
(21) Ejector lever
(22) Captive screw
Manual version: T2-082324-20141219-C-1.02 BOM: 3123A124
ii
Table 1 Card specifications
Item S
p
ecification
CF card
One CF card slot, 256MB by default for the external CF card
256 MB, 512 MB, or 1 GB for an optional external CF card
Dimensions (H × W × D) 40.1 × 400 × 380 mm (1.58 × 15.74 × 14.96 in)
Hot swapping Supported
Ports
• 1 console port
• 2 USB ports (reserved for future use)
• 2 pairs of combo ports, each pair containing the following ports:
{ 1 x 10/100/1000BASE-T copper port
{ 1 x 1000BASE-X SFP fiber port
You can use the combo enable { copper | fiber } command to activate either of
the ports in a pair. By default, the copper combo port is activated.
Ambient temperature
• Operating: 0°C to 45°C (32°F to 113°F)
• Not operating: –40°C to +70°C (–40°F to +158°F)
Ambient relative humidity
• Operating: 10% to 95%, noncondensing
• Non-operating: 5% to 95%, noncondensing
Compatible device models H3C S9500 series switches
System software version See the release notes that come with the card.
Table 2 Console port specifications
Item S
p
ecification
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
• Provides connection to an ASCII terminal.
• Provides connection to the serial port of a local or remote PC (through a
pair of modems) that is running a terminal emulation program.
• Supports command line interface (CLI).
Table 3 10/100/1000BASE-T copper port specifications
Item S
p
ecification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Supported cable Category-5 (or above) twisted pair cable
Transmission distance 100 m (328.08 ft)
Manual version: T2-082324-20141219-C-1.02 BOM: 3123A124
iii
Item S
p
ecification
Operating mode
• 10 Mbps, half/full duplex
• 100 Mbps, half/full duplex
• 1000 Mbps, full duplex
Table 4 1000BASE-X fiber port specifications
Item S
p
ecification
Transceiver module SFP
Connector LC
Interface standard 802.3, 802.3u, and 802.3ab
Operating mode 1000 Mbps, full duplex
Table 5 1000BASE-X SFP port specifications
Gigabit SFP module
Central
wavelength
Connector
Cable specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A 850 nm LC
62.5/125μm
multi-mode optical fiber
0.55 km (0.34 miles)
SFP-GE-LX-SM1310-A 1310 nm LC
9/125 μm single-mode
optical fiber
10 km (6.21 miles)
SFP-GE-LH40-SM1310 1310 nm LC
9/125 μm single-mode
optical fiber
40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 nm LC
9/125 μm single-mode
optical fiber
40 km (24.86 miles)
SFP-GE-LH70-SM1550 1550 nm LC
9/125 μm single-mode
optical fiber
70 km (43.5 miles)
SFP-GE-LH100-SM1550 1550 nm LC
9/125 μm single-mode
optical fiber
100 km (62.14 miles)
4 LEDs
The card provides LEDs to show the operating status of the card and interfaces.
Table 6 LED description
LED Status Descri
p
tion
CF card(CFS)
Off The CF card is not present or cannot be identified.
Steady green
The CF card is present and has passed the power on self test
(POST).
Flashing green
The system is reading the CF card data. Do not unplug the CF
card.
Manual version: T2-082324-20141219-C-1.02 BOM: 3123A124
iv
LED Status Descri
p
tion
GE/Combo copper port
(LINK/ACT)
Off No link is present on the port.
Steady green A link is present on the port.
Flashing yellow The port is sending or receiving data.
5 Installing and removing the card
CAUTION:
• Wear a well-grounded ESD wrist strap or ESD gloves before you install or remove the card.
• Do not touch the components on the PCB.
5.1
Installing the card
1. Locate the slot where you will install the LSB1FW2A0, and remove the blank panel from the
position. This manual describes installing the LSB1FW2A0 to slot 2.
2. Push the module with the components facing upward into the slot along the guide rails until the
positioning hole of the module is seated onto the positioning pin on the backplane. Push the ejector
levers inward to lock the module in place.
3. Fasten the captive screws on the module with a Philips screwdriver.
Figure 2 Installing the card
1
2
2
Manual version: T2-082324-20141219-C-1.02 BOM: 3123A124
v
5.2
Removing the card
1. Use a Phillips screwdriver to loosen the captive screws at both sides of the card.
2. Pull the ejector levers at both sides of the card outward to separate it from the backplane, and then
pull the card along the guide rails to remove it from the chassis.
3. Place the card on an anti-static workbench with the surface-mounted components up. You can also
put it in an anti-static bag.
4. If you are not going to install a new card, install a filler panel to prevent dust and ensure good
ventilation in the switch.
6 Logging in to the card
The card uses an independent operating system. Before you can configure the card, you must log in to
the card by using one of the following methods:
• Log in from the switch's CLI through the oap connect command.
• Log in through the card's Web interface, console port, Telnet, or SSH.
H3C recommends that you log in to the card from the switch's CLI the first time you access the card. This
section includes a procedure for logging in from the switch's CLI. For more information about other login
methods, see H3C SecBlade II Firewall Cards Configuration Guide.
To log in to the card from the switch's CLI, perform the following task in user view:
Task Command
Remarks
Log in to the card through OAP.
• In standalone mode:
oap connect slot slot-number
• In IRF mode:
oap connect chassis
chassis-number slot slot-number
To return to the CLI interface of the
switch, press Ctrl+K.
7 Software upgrade
The card uses independent BootWare and system software images. You must upgrade the card software
separately from the switch software. To ensure a successful card upgrade, H3C recommends that you
upgrade the card through the card's console port or management Ethernet port. For more information
about software upgrade of the card, see the release notes that come with the card.
8 Obtaining documentation
To access the most up-to-date H3C product documentation on the World Wide Web
at http://www.h3c.com
:
1. Go to http://www.h3c.com/Technical_Documents, or click Technical Support & Documents >
Technical Documents on the top navigation bar at http://www.h3c.com
.
2. Click Security Products > H3C SecBlade Module to choose the desired product category and
model.
Copyright © 2014 Hangzhou H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

H3C SR6600 SPE-FWM Card Manual

H3C
Brand
H3C
Model
SR6600 SPE-FWM
Type
Card Manual
This manual is also suitable for

H3C SR6600 SPE-FWM is a versatile and powerful security appliance that provides a comprehensive suite of network security features to protect your network from a wide range of threats.

With its high-performance hardware and advanced software, the H3C SR6600 SPE-FWM can handle even the most demanding network traffic, making it ideal for use in large enterprises and data centers. Some of the key features of the H3C SR6600 SPE-FWM include:

Stateful firewall: The H3C SR6600 SPE-FWM's stateful firewall inspects all incoming and outgoing traffic and blocks any packets that do not match the defined security rules. This helps to protect your network from unauthorized access, Denial of Service (DoS) attacks, and other threats.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents