Winmate W05TA3S-PCT3AC Quick start guide

Please read these instructions carefully before using this product, and save this manual for future use.

5” S-Series HMI

W05TA3S-PCT3AC

Freescale® Cortex® A9 i.MX6 Dual Core, 1 GHz

Quick Start Guide

Document Part Number: 9152050I0000

Version 1.1

2

5" S-Series HMI Quick Start Guide

Contents

Preface 3

Getting Started 4

Unpacking 5

Accessories 5

Description of Parts 6

Connector Description 8

DC Input Connector 8

LAN (RJ45) Connector 8

USB A Type Connector 8

Digital Input / Output Connector 9

Turning On or Off Your Device 10

Turning On 10

Turning OFF 10

Using Camera 11

Camera Application 11

Taking Pictures 11

Opening the Gallery 11

TARS Test Application 12

Location and Interface 12

Testing LED Light Bar 13

Testing HF RFID Reader 14

HF RFID Reader Introduction 14

Scanning HF RFID Tag 14

Testing DIDO 15

Software Developer Support 16

Software System Diagram 16

Winmate Software Development Kit 16

Technical Specifications 17

HMI Device Specifications 17

HF RFID Reader Specifications 18

3

Preface

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in any form or

by any means, electronic or mechanical, for any purpose, without the prior written permission

of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer

We reserve the right to make changes, without notice, to any product, including circuits and/or

software described or contained in this manual in order to improve design and/or performance.

We assume no responsibility or liability for the use of the described product(s) conveys no

license or title under any patent, copyright, or masks work rights to these products, and make

no representations or warranties that these products are free from patent, copyright, or mask

work right infringement, unless otherwise specified. Applications that are described in this

manual are for illustration purposes only. We make no representation or guarantee that such

application will be suitable for the specified use without further testing or modification.

Warranty

Our warranty guarantees that each of its products will be free from material and workmanship

defects for a period of one year from the invoice date. If the customer discovers a defect, we

will, at his/her option, repair or replace the defective product at no charge to the customer,

provide it is returned during the warranty period of one year, with transportation charges

prepaid. The returned product must be properly packaged in its original packaging to obtain

warranty service. If the serial number and the product shipping data differ by over 30 days, the

in-warranty service will be made according to the shipping date. In the serial numbers the third

and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g.,

with A for October, B for November and C for December).

For example, the serial number 1W18Axxxxxxxx means October of year 2018.

Customer Service

We provide a service guide for any problem by the following steps: First, visit the website of

our distributor to find the update information about the product. Second, contact with your

distributor, sales representative, or our customer service center for technical support if you

need additional assistance.

You may need the following information ready before you call:

 Product serial number

 Software (OS, version, application software, etc.)

 Description of complete problem

 The exact wording of any error messages

In addition, free technical support is available from our engineers every business day. We are

always ready to give advice on application requirements or specific information on the

installation and operation of any of our products.

4

5" S-Series HMI Quick Start Guide

Getting Started

Congratulations on purchasing Winmate® 5” S-Series HMI. Interactive and smart automation

systems of intelligent buildings are in a fast growing phase. Winmate® multi-touch S-Series HMI is

suitable for home automation and room management systems. Flat surface is easy-to-clean and

delivers aesthetically pleasing look for any interior. By connecting to centralized database, it can

provide real time update for booking status and available schedule, or perform as a synchronous

display in meetings.

Winmate® 5” S-Series HMI powered by TI Cortex® A8 AM3354 1GHz with DSP processor and

support Android 4.4 operating systems. The HMI device features P-Cap touch-screen. In addition,

the HMI device model supports an exceptional feature - LED Light Bar. With the help of red, green,

blue and orange LED indicators you can see the status of the machine or processes afar. It

significantly reduces power consumption by keeping the display turned off.

Winmate® 5” S-Series HMI features:

 TI Cortex A8 AM3354 1GHz with Android Operating System

 Fanless cooling system and ultra-low power consumption

 5'' WVGA TFT (LED backlight) with P-CAP touch screen

 Gigabit LAN with PoE (IEEE 802.3AT) Solution

 Built-in non-contact HF RFID Module

 2MP front-facing camera for interactive communication

 Multi-Color(G,R,B) Programmable LED Light Bar Indicator

 Unidirectional-Mic and Speaker for VoIP application

 Wide-distance (10M) RF controller for Digital Out device trigger application

 All-in-one design, completed solution for cost-saving and space-saving

5

Getting Started

Unpacking

Carefully remove the box and unpack your device. Please check if all the items listed below are

inside your package. If any of these items are missing or damaged contact us immediately.

Accessories

Standard factory shipment list:

 5” HMI Device

 Quick Start Guide

(Hardcopy)

 Power Cable

 AC Adapter

(12V/ 50W)

 Terminal Block 3 pin

6

5" S-Series HMI Quick Start Guide

Description of Parts

Front Side:

Rear Side:

I/O Side:

Speaker

Kensington Lock

5” 800*480 LED

panel with PCAP

Touch Screen

2MP Camera

Mic

RFID Reader

LED Light bar

SD Card Slot

DC 12V in

Digital I/O

LAN / PoE

Reset

Button

USB A Type

7

Description of Parts

Dimensions:

8

5" S-Series HMI Quick Start Guide

Connector Description

DC Input Connector

DC terminal block power source input is a 3-pin terminal block that has to be secured with

screws to the HMI device housing

LAN (RJ45) Connector

The 5” S-Series HMI supports one 10/100/1000 Mbps Ethernet interface for connecting to the

internet.

USB A Type Connector

Use USB A Type (USB2.0) connector to connect your HMI device to other USB2.0 compatible

devices.

Pin No.

Symbol

Description

1

VIN+

12V DC Input +

2

VIN-

12V DC Input -

3

GND

Ground

Voltage

Minimum Voltage 11.4V

Maximum Voltage 12.6V

Maximum Current 4.2A

Pin №

Signal Name

Pin №

Signal Name

1

TX1+

2

TX1-

3

TX2+

4

TX2-

5

TX3+

6

TX3-

7

TX4+

8

TX4-

Pin №

Signal Name

Pin №

Signal Name

1

+5V

2

Data-

3

Data+

4

GND

9

Connector Description

Digital Input / Output Connector

Digital Input and Output 2 in / 2 out (one 12V/1A for electromagnetic lock).

Go Refer to Testing DIDO section in this guide to test the DIDO functions.

Pin №

Name

Pin №

Name

1

GND

2

DO0

3

DO1

4

DO_COM

5

DI0

6

DI1

7

GND

Voltage

Digital output:

Open drain to 40V ; Maximum load 2.0A

Digital input:

Level 0: close to GND; Level 1: 2.5~12V

10

5" S-Series HMI Quick Start Guide

Turning On or Off Your Device

Turning On

Follow the following steps to turn on your device:

1. Connect the power cable to AC to DC adapter.

2. Connect the open wire of AC to DC adapter to the terminal block female connector and

tighten the screws to secure it to the HMI device.

3. Connect the terminal block female connector to the device's male connector.

4. Plug the power cord to the AC outlet and the device will turn on automatically.

CAUTION

Use only the AC adapter included in your package

(Rating: Output 4.2 A). Using other AC adapters may damage the device.

Turning OFF

Remove the power input to shut down the device.

 Press the reset button to reboot the HMI device.

ALTERNATING CURRENT

This product must be grounded. Use only a grounded AC outlet. Install the additional

PE ground wire if the local installation regulations require it.

Reset Button

11

Using Camera

Winmate® 5” S-Series HMI has a built-in front camera, which allows you to take photos and record

video clips.

Camera Application

1. Tap the launcher and then tap Camera .

Camera opens in Portrait mode, ready to take a picture or shoot a video.

Taking Pictures

1. Tap the launcher and then tap Camera .

2. Tap button to start or stop recording.

 The photos or video can be previewed in the preview window.

 If you want play the video you have recorded, go into the video player and select the

video you want to play.

 If you want to view photos, select the picture viewer and choose which photos you

want to see.

3. Tap button to change shooting mode.

4. Tap button to change camera setting such as exposure and so on.

Opening the Gallery

1. Tap the launcher and then tap Gallery .

2. Tap a folder to view the pictures or video inside in full screen mode.

3. Flick the pictures left or right to view the previous or next pictur

12

5" S-Series HMI Quick Start Guide

TARS Test Application

The HMI device comes with pre-installed application – “TARS Test” for testing main features such

as LED Light Bar, DIDO and HF RFID.

Location and Interface

To open the application, go to all APPS menu, then tap TARS Test icon.

TARS Test Application Interface

13

TARS Test Application

Testing LED Light Bar

The 5” S-Series HMI equipped with LED Light Bar located on the bottom front side of the device.

Users can test this feature with TARS Test APP developed by Winmate.

1. Go to all APPS menu, then tap TARS Test icon.

2. User can test Red, Green and Blue Light Bar duty level.

 Tap the arrow to the right to increase light intensity.

 Tap the arrow to the left to decrease light intensity.

14

5" S-Series HMI Quick Start Guide

Testing HF RFID Reader

HF RFID Reader Introduction

HF RFID is an initial of Radio Frequency Identification, which is also called electrical tag. The

principle of RFID is to tag the target by radio frequency and process the data reading and

transporting instead of mechanic and optical contact. HF RFID system consists of the hardware

and software. The hardware part includes the HF RFID tag and reader, and software part

includes its application system. HF RFID is commonly used for ticketing, payment, access

control and data transfer applications.

The RFID Reader is located on the bottom right front side of the HMI device.

The RFID’s frequency of electrical tag is 13.56 MHz.

Scanning HF RFID Tag

1. Go to all APPS menu, then tap TARS Test icon.

2. While TARS Test application is open, bring a card close to the RFID icon on the front side

of the HMI device.

15

TARS Test Application

Number

Description

XXXXXXXXXXXXXABCDEF

Displays the information written in the card

Testing DIDO

1. Go to all APPS menu, then tap TARS Test icon.

2. In the TARS Testing window, see DIDO.

16

5" S-Series HMI Quick Start Guide

Software Developer Support

Software System Diagram

This diagram describes the software system of Winmate® 5” S-Series HMI.

Winmate Software Development Kit

Winmate® provides Software Development Kit (SDK). The table below lists SDK provided by

Winmate for 5” S-Series HMI.

Devices

Support

RFID Reader

Not Necessary (Baud rate 9600,8N1 and giving a ASCII string)

DI/DO

4DI,4DO are controlled by Linux file system code

WebCAM

Standard UVC

LCD Backlight

Control

Test AP- Winmate source code reference

UART

Software switch to RS232/422/485

To find Drivers and SDK, please refer to the Driver CD that comes in the package or contact us.

17

Technical Specifications

HMI Device Specifications

Model Name

W05TA3S-PCT3AC

Display

Specification

Size

5” TFT (LED Backlight)

Pixel Pitch

0.045 (H) x 0.135 (V)

Resolution

800 x 480

Luminance (



)

300 (typ.)

Contrast Ratio

500 : 1 (typ.)

Viewing Angle

-70~70(H),-50~70(V)

Touch

PCAP Multi-Touch support 5 points

System

Specification

CPU

TI Cortex® A8 AM3354 1GHz with DSP

Memory

512MB DDR2 SDRAM 533MHz

Graphics

PowerVR SGX 3D Gfx

Storage

1GB 8bit Nand Flash (OS)

Operating System

Android 4.2.2

I/O Connectors

DC-Input

1 x Phoenix Type Power Jack

Ethernet

1 x RJ 45 10/100/1000

(Support PoE function IEEE 802.3at)

Reset Button

1 x Reset Button with Blue LED indicator

Expansion Storage

1 x Micro SD Card Slot (with 16GB SD card)

Digital I/O

2 in / 2 out (one 12V/1A for electromagnetic

lock)

Peripheral

Camera

2 MP front-facing camera

RFID (HF, 13.56MHz)

Supporting 14443A , ISO 15693 / ISO18092,

3cm (Maximum Reading Range)

RF Remote Control

443MHz RF module with controller ,10M

(Maximum Active Range)

Audio Input

MIC (Uni-directional)

Audio Output

1Watt Speaker

LED Light Bar

Indicator

RGB multi-color

Power

Management

Power Input

12V DC-in Power input (Phoenix type)

Power Over Ethernet

Support IEEE 802.3at (25W)

Power Consumption

10W (w/o DIDO Device)

Mechanical

Specifications

Dimensions

(W x L x H)

138 x 138 x 29 mm

Mounting

VESA Mount (75 x 75 mm)

Cooling System

Fanless design

Environmental

Considerations

Operating Temp.

0°C ~ +55°C

Humidity

10% ~ 90% (non-condensing, RH)

IP Proof

IP54 (Front side)

18

5" S-Series HMI Quick Start Guide

HF RFID Reader Specifications

Part Number

RF-521

RF Transmit Frequency

13.56MHz

F/W version

V1.00B / V1.03

Supported Transponder

ISO 15693 (R/W)

ISO 14443-A( R/W)

ISO 14443-B (Read UID)

ISO18092 (R/W)

Power Supply

DC 5V

Power Consumption

Operating: 80mA (max)

Standby: 4mA

Communication Protocol

The Nation standard UART format

Operating Temperature

-20°C to + 85°C

Storage Temperature

-20°C to + 85 °C

Storage Humidity

5 ~ 97% non-condensing

Dimensions (Unit : mm)

31 x 21.5 x 5.3 ( L x W x H )

Weight

2g (around)

ANT-4424 Specifications

Part Number

ANT-4424-WM-IPX40

Antenna Impedance

50 ohm @13.56MHz

Operating Temperature

-20°C to + 85°C

Storage Temperature

-20°C to + 85°C

PCB Dimensions

L: 44mm x W: 24mm x H: 1.0mm

CN1 Connector Cable

MHF Connector

MINI 1.13 Coaxial Cable 40mm

Notes

______________________________________________________________________________

Winmate Inc.

9F, No.111-6, Shing-De Rd., San-Chung District,

New Taipei City 24158, Taiwan, R.O.C

www.winmate.com

Winmate W05TA3S-PCT3AC Quick start guide

Related papers

Other documents