Winmate W10IB3S-PCH2-PoE S-Series Quick start guide

Brand
Winmate
Model
W10IB3S-PCH2-PoE S-Series
Type
Quick start guide

This manual is also suitable for

Winmate W10IB3S-PCH2-PoE S-Series is a 10.1" HMI device with a 1280 x 800 resolution and a P-Cap multi-touch screen. It is powered by a 1.83GHz Intel® Celeron® N2930 processor and supports Windows 10 IoT, Windows Embedded 8.1 Industry Pro, Windows Embedded 8Standard, Windows 7 Pro for Embedded Systems, and Windows Embedded Standard 7– WS7P. The device has a fanless cooling system and ultra-low power consumption, and it supports PoE. Other features include dual Gigabit Ethernet, front IP65 water and dust proof, and a red/ green/ blue/ orange LED light bar indicators on both sides.

Winmate W10IB3S-PCH2-PoE S-Series is a 10.1" HMI device with a 1280 x 800 resolution and a P-Cap multi-touch screen. It is powered by a 1.83GHz Intel® Celeron® N2930 processor and supports Windows 10 IoT, Windows Embedded 8.1 Industry Pro, Windows Embedded 8Standard, Windows 7 Pro for Embedded Systems, and Windows Embedded Standard 7– WS7P. The device has a fanless cooling system and ultra-low power consumption, and it supports PoE. Other features include dual Gigabit Ethernet, front IP65 water and dust proof, and a red/ green/ blue/ orange LED light bar indicators on both sides.

Please read these instructions carefully before using this product, and save this manual for future use.
10.1” S-Series HMI
W10IB3S-PCH2AC-PoE
W10IB3S-PCH2-PoE
Quick Start Guide
V1.1
Document Part Number: 9154111I100A
Contents
Getting Started 3
Unpacking 4
Description Of Parts 5
Dimensions 6
Mounting 7
VESA Mount 7
Flush/ Panel Mount 7
Connector Description 8
DC Input Terminal Block Connector 8
Serial Port Connector 8
PoE/ LAN Connector 9
USB 2.0/ USB 3.0 Connector 9
HDMI Connector 9
Digital I/O Connector 10
Turning On or Off 11
Turning ON 11
Turning OFF 12
Operating the HMI Device 13
System Settings 13
Hot Tab Menu 13
Utilities 14
Brightness 14
Volume 14
LED Light Bar (Easy-Testing) 15
Performance 15
Touch Lock 15
Using HF RFID Reader 16
Reading Mode 17
Writing Mode 18
Using Front Camera 19
Opening the Camera 19
Shooting Photos 20
Recording Videos 21
Camera Settings 21
How to Enable Watchdog 23
Software Developer Support 25
Winmate Software Development Kit 25
Winmate Download Center 25
Winmate File Share 25
Technical Specifications 26
HMI Device Specifications 26
HF RFID Reader 29
3
Getting Started
Congratulations on purchasing Winmate® 10.1” S-Series HMI. Interactive and
smart automation systems of intelligent buildings are in a fast growing phase.
Winmate multi-touch S-Series HMI is suitable for home automation and room
management systems. Flat surface is easy-to-clean and delivers aesthetically
pleasing look for any interior. By connecting to centralized database, it can provide
real time update for booking status and available schedule, or perform as a
synchronous display in meetings.
S-Series HMI run on 1.83GHz Intel® Celeron® N2930 processor and support
Windows 10 IoT, Windows Embedded 8.1 Industry Pro, Windows Embedded
8Standard, Windows 7 Pro for Embedded Systems, and Windows Embedded
Standard 7– WS7P. For easy, quick and cost effective network installations both
models support PoE. These models sealed with front IP 65 dust and water proof,
and IP22 on the back side. Optional HF RFID 13.56 MHz is especially useful in
access control applications.
S-Series HMI has an exceptional feature - LED light bar. With the help of red,
green, blue and orange LED indicators you can see the status of the machine or
processes afar. It significantly reduces power consumption by keeping the display
turned off.
Winmate® 10.1” S-Series HMI features:
10.1'' 1280 x 800 Resolution with P-Cap multi-touch screen
PoE standard IEEE 802.3at (25 W)
Fanless cooling system and ultra-low power consumption
Dual Gigabit Ethernet
Front IP65 water and dust proof
Red/ Green/ Blue/ Orange LED light bar indicators on both sides
Optional HF RFID Reader
Optional 2MP Front Camera
Room booking schedule, access control, room information display
4
Please read these instructions carefully before using this product, and save this guide for future
use.
Unpacking
Carefully remove the box and unpack your device. Please check if all the items
listed below are inside your package. If any of these items are missing or
damaged contact us immediately.
Standard factory shipment list:
10.1” HMI Device
Quick Start Guide
(Hardcopy)
Driver CD & User
Manual
AC Adapter
(12V/ 50W)
Power Cable
Terminal Block 3 pin
External USB Cable
VESA Mounting Screws
5
Description Of Parts
*Digital I/O is an optional connector and may not be present in your model.
6
Please read these instructions carefully before using this product, and save this guide for future
use.
Dimensions
Dimensions (W x L x H): 263.28 x 171 x 35.7 mm
*Note: Measurements shown in mm.
**Note: this is a simplified drawing and some components are not marked in detail.
7
Mounting
S-series HMI devices come with different mounting options suitable for most of the
industrial and commercial applications.
VESA Mount
Dimensions
Screw hole diameter
Compatibility
75 x 75 mm
VESA M4x5 mm
Swing arm mounting kits
Flush/ Panel Mount
Wall cutout
Screw hole diameter
157.6 x 249 mm
M3x4 mm
8
Please read these instructions carefully before using this product, and save this guide for future
use.
Connector Description
This section explains how to connect external interfaces to the HMI device.
DC Input Terminal Block Connector
DC power source input is a 3 pin terminal block connector.
Serial Port Connector
Use COM1 serial port connector to connect your HMI to external devices such as
mouse, modem or printer. You can configure serial port setting via jumpers
located on the motherboard. You need to open the housing in order to access
the jumpers.
CAUTION/ ATTENTION
It is recommended to use factory jumper settings. Opening the housing
when it is sealed may damage the device and its parts.
Refer to User Manual for instructions on how to configure serial port setting.
Voltage
Minimum Voltage 11.4V
Maximum Voltage 12.6V
Maximum Current 4.2A
Pin №
RS-232
(Default)
RS-422
RS-485
1
DCD
TxD-
D-
2
RXD
TxD+
D+
3
TXD
RxD+
NC
4
DTR
RxD-
NC
5
GND
GND
GND
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC
9
PoE/ LAN Connector
The 10.1” S-Series HMI supports one RJ45 10/100/1000 Mbps Ethernet
interface for connecting to the internet. Support IEEE 802.3at PoE.
USB 2.0/ USB 3.0 Connector
Use USB 2.0/ USB 3.0 connector to connect your HMI device to other USB 2.0/
USB 3.0 compatible devices.
USB2.0 / USB 3.0
HDMI Connector
Pin №
Name
Pin №
Name
1
TX1+
2
TX1-
3
TX2+
4
TX2-
5
TX3+
6
TX3-
7
TX4+
8
TX4-
Pin №
Name
Pin №
Name
1
+5V
2
USB_D-
3
USB_D+
4
GND
5
STDA_SSRX-
6
STDA_SSRX+
7
GND_DRAIN
8
STDA_SSTX-
9
STDA_SSTX+
10
+5V
11
USB_D-
12
USB_D+
13
GND
Pin
№
Name
Pin №
Name
1
TMDS_DATA2+
2
GND
3
TMDS_DATA2-
4
TMDS_DATA1+
5
GND
6
TMDS_DATA1-
7
TMDS_DATA0+
8
GND
9
TMDS_DATA0-
10
TMDS_CLOCK+
11
GND
12
TMDS_CLOCK-
13
CEC
14
NC
15
DDC_CLOCK
16
DDC_DATA
17
GND
18
5V
19
Hot Plug Detect
10
Please read these instructions carefully before using this product, and save this guide for future
use.
Digital I/O Connector
Pin №
Name
Pin №
Name
1
GND
2
DO0
3
DO1
4
DI0
5
DI1
Voltage
Digital output:
Open drain to 40V ; Maximum load 2.0A
Digital input:
Level 0: close to GND; Level 1: 2.5~12V
11
Turning On or Off
Turning ON
Follow the following steps to turn on your device:
1. Connect HMI device to a thermal block (3-pin).
2. Connect the other side of the thermal block to the AC adapter.
3. Connect the AC adapter to the power cord.
4. Plug in the power cord to a working AC wall outlet. The device will boot
automatically.
CAUTION
Use only the AC adapter (12V/ 50W) included in your package
(Rating: Output 4.2 A). Using other AC adapters may damage the
device.
ALTERNATING CURRENT
This product must be grounded. Use only a grounded AC outlet.
Install the additional PE ground wire if the local installation regulations
require it.
12
Please read these instructions carefully before using this product, and save this guide for future
use.
Turning OFF
To shut down the device:
1. Tap Start >Shut down.
2. Wait for your HMI device to completely turn off before disconnecting the
power cord (if necessary).
13
Operating the HMI Device
Winmate® 10.1” S-Series HMI support several versions of Windows OS:
Windows 10 IoT, Windows Embedded 8.1 Industry Pro, Windows Embedded 8
Standard, Windows 7 Pro for Embedded Systems, and Windows Embedded
Standard 7– WS7P.
IMPORTANT:
The device is shipped with the OS System according to your order.
Contact us if you have any questions regarding OS settings.
System Settings
Hot Tab Menu
1. Double-click the Hot Tab icon on the Windows desktop.
2. The Hot Tab main menu will appear on the screen as shown below.
NOTE:
RFID and LED Light Bar are optional features and may not be
present in your model.
14
Please read these instructions carefully before using this product, and save this guide for future
use.
Utilities
Utilities category allows automatically changing
orientation from landscape to portrait mode or rotating
the desktop to a different degree as 0°, 90°, 180°, and
270°.
Brightness
Tap Brightness button to show current brightness level.
To reduce the brightness, drag by touch to
the left.
To enhance the brightness, drag by touch to
the right.
Tap Close to save changes and exit the interface.
Volume
Tap Volume button to show your current volume level.
To decrease the volume, drag by touch to the
left.
To increase the volume, drag by touch to the
right.
Tap Close to save changes and exit the interface.
15
LED Light Bar (Easy-Testing)
Notice that LED Light Bar is an optional feature for 10.1” S-Series HMI and may
not be present in your device.
Tap Light Bar to access the LED light bar control panel, and select Red / Green
/ Blue/ Orange color to be displayed on the LED Bar.
Performance
User can adjust the performance level of the HMI device. There are four options
available:
Extreme performance
Office Document
High performance
Power Saving
Touch Lock
To LOCK touch screen, double-click the Hot Tab icon on the Windows
desktop, and tap Touch Lock.
To UNLOCK the touch screen, tap button to the right.
16
Please read these instructions carefully before using this product, and save this guide for future
use.
Using HF RFID Reader
Notice that HF RFID Reader is an optional feature for 10.1” S-Series HMI and may
not be present in your device.
HF RFID is commonly used for ticketing, payment, and data transfer applications.
The RFID Reader is located on the bottom right front side of the HMI device.
The COM Port setting in RFID Reader is “COM 14”
1. Double-click the RFID icon on the Windows desktop.
2. Reader menu appears on the screen as shown below.
Note:
The picture below of Reader Demo Version 1.4 is for illustration
purposes only. Your Reader version may differ from the picture
below.
17
Reader Demo Version 1.04
Reading Mode
Select the default RFID Reader COM14or press Search on the upper left corner
of the screen. The system will automatically find RFID COM port, show the
Version.
UID0 Menu
The system will read the data once the card will be near. You can select different
reader modes. Each mode is described below.
Item №
Key button
Function
3
A0- Continuous
Read (default)
The RFID Reader will perform a series of
multiple scanning operations
Item №
Key button
Function
1
E1- Version
Displays the current version of RFID Reader
system
2
E2- Reset
Reset all settings
18
Please read these instructions carefully before using this product, and save this guide for future
use.
4
A1- Once Read
The RFID Reader will perform a single
scanning operation during the card is near
5
A9- Type Read
The RFID Reader will perform a scanning
operation of IC type tag
To scan the card, bring it close to the right bottom front side of device with RFID
icon.
Item №
Data 32
Function
6
XXXXABCDEF
Display the information written in the card
Writing Mode
Refer to the RFID Porting Guide SDK to configure Write Mode parameters.
19
Using Front Camera
Notice that 2MP Front Camera is an optional feature for 10.1” S-Series HMI and
may not be present in your device.
NOTE:
You camera screen may differ from the pictures in thus user
manual.
Opening the Camera
Perform one of the following to open the camera:
1. Press the F1 key.
2. Tap then double-tap to display the HotTab screen. Select Camera.
The Camera Screen
No
Item
Description
1
Video
Tap to record videos
2
Photo
Tap to capture photos
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

Winmate W10IB3S-PCH2-PoE S-Series Quick start guide

Brand
Winmate
Model
W10IB3S-PCH2-PoE S-Series
Type
Quick start guide
This manual is also suitable for

Winmate W10IB3S-PCH2-PoE S-Series is a 10.1" HMI device with a 1280 x 800 resolution and a P-Cap multi-touch screen. It is powered by a 1.83GHz Intel® Celeron® N2930 processor and supports Windows 10 IoT, Windows Embedded 8.1 Industry Pro, Windows Embedded 8Standard, Windows 7 Pro for Embedded Systems, and Windows Embedded Standard 7– WS7P. The device has a fanless cooling system and ultra-low power consumption, and it supports PoE. Other features include dual Gigabit Ethernet, front IP65 water and dust proof, and a red/ green/ blue/ orange LED light bar indicators on both sides.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents