JUNG LSCARDRFID Operating instructions

LSCARDRFID
JUNG
Brand
JUNG
Model
LSCARDRFID
Type
Operating instructions

This manual is also suitable for

Key card holder RFID and energy saving unit
23.07.20201 / 40024018702
Key card holder RFID
Ref.-no.: .. CARD RFID ..
Energy saving unit
Ref.-no.: ESU 230-2
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, re or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the devise or load.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
1
2
3
4
Fig. 1: Device components
(1) Energy saving unit
(2) Frame
(3) Key card holder RFID
(4) RGB lens
3 Function
Intended use
- Switching of lighting and other loads
- Triggering of external control systems
- Installation in ush-box according to DIN 49073
Product characteristics
- Operation with RFID cards according to ISO/IEC 14443 and ISO/IEC 15693
- 2 make contacts, one of them with congurable run-on time
- Status indication with RGB lens
- Lens is dimming down 30 s after inserting the card
- Run-on time is signalled by RGB lens after removing the card
GB
Key card holder RFID and energy saving unit
23.07.20202 / 40024018702
4 Operation
Lens lights up blue.
Device is ready for operation.
• Insert card
Outputs 1+2 switch on
Lens lights up green (60 %)
After 30 seconds the lens is dimming down to 10 % brightness
• Remove card
Output 1 switches o
Lens ashes green for approx. 60 seconds
Lens lights up blue (pilot light)
Output 2 switches o
RFID
RFID
RFID RFID
RFID
30 s 60 s
BL 60 % GN 60 % GN 10 % GN BL 60 %
A1
A2
A1
A2
A1
A2
A1
A2
A1
A2
Fig. 2: Signalling
Signalling
Absence: No card in key card holder.
Lens lights up blue 60 %.
Presence: Card is inserted in key card holder.
Lens lights up green 60 %,
after 30 seconds green 10 %.
Remove card: Lens ashes green, after 60 seconds lights up blue 60 %.
i Lens colour, brightness and time/duration can be customized online before ordering. Subsequent changes are
possible with conguration card (ref.no.: CONFIG CARD) which can be ordered separately.
www.jung.de/hotelcard
Stand-by colour: blue, red, green
Stand-by brightness: 0 ... 100 % (60 %)
Activation signal: 0 ... 240 s (30 s)
Run-on time: 0 ... 240 s (60 s)
Brightness “presence”: 0 ... 100 % (10 %)
Key card holder RFID and energy saving unit
23.07.20203 / 40024018702
5 Information for electrically skilled persons
Installation and electrical connection
DANGER
Electric shock from touching live parts in the installation environment.
An electric shock can be fatal.
Before working on the device, disconnect the power and cover live parts in the area.
Connecting and tting the device
N
L
1
5
A1 A2
AC 230 V~
Fig. 3: Connection
LOW
MID
HIGH
A1 A2
N
L
AC 230 V~
1
6
5
Fig. 4: Connection to TRD .. 230..8 ..
(5) Load
(6) Temperature controller e.g. TRD .. 23028 .. or TRD .. 23048 ..
• Connect load according to wiring diagram (g. 3 or 4).
• Install insert (1) in wall box, terminals must be at the bottom.
• Attach the frame (2) and the cover (3).
• Switch on mains voltage.
Key card holder RFID and energy saving unit
23.07.20204 / 40024018702
6 Technical data
ESU 230-2 (energy saving unit)
Rated voltage AC 110 ... 230 V~
Mains frequency 50 / 60 Hz
Switching current AC1 (cos ϕ > 0.8) 16 A
Current carrying capacity, device (A1+A2) max. 16 A
Switch type 2 make contacts
Contact type µ
Ambient temperature -5 ... +45 °C
Storage/transport temperatur -25 ... +75 °C
Stand-by power max. 0.94 W
Connection max. 1 x 2.5 mm²
or 2 x 1.5 mm²
Connected load (AC 230 V~)
Output 1 (A1)
Ohmic 3000 W
Motors 1160 VA
Lamp loads
HV halogen lamps 1000 W
LV halogen lamps with electronic transformer 1000 W
Output 2 (A2)
Run-on time 0 ... 240 s (60 s)
Ohmic 3000 W
Capacitive 16 A / 140 µF
Motors 1380 VA
Lamp loads
HV halogen lamps 2500 W
LV halogen lamps with
electronic transformer 1500 W
inductive transformer 1200 VA
HV LED lamps typ. 400 W
Power reduction
per 5 °C in excess of 25 °C -10 %
in wooden or dry construction walls -15 %
in multiple combinations -20 %
.. CARD RFID .. (key card holder RFID)
RFID standard ISO/IEC 14443
ISO/IEC 15693
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +75 °C
7 Warranty
The warranty follows about the specialty store in between the legal framework as provided for by law.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

JUNG LSCARDRFID Operating instructions

LSCARDRFID
JUNG
Brand
JUNG
Model
LSCARDRFID
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents