ESAB TR-23A Truck Kit User manual

Brand: ESAB

Model: TR-23A Truck Kit

Type: User manual

Be sure this information reaches the operator.

You can get extra copies through your supplier.

INSTRUCTIONS for

TR-23A TRUCK KIT

Item No. 36352

for mounting on the

V 352, V 382, V 452, V 582, V 652cvcc, V 782cvcc, Heliarc 252

and Heliarc 352 Power Sources

F-15-334

April, 1996

This kit includes the following components:

2 — 5/16"-18 Screw 1.00" Long

2 — 5/16" Flat Washer

1 — Cylinder Support, 36353BK

1 — Cylinder Tray/Axle Assembly, 36051BK

1 — Handle Shaft, 36356BK

2 — Swivel Castor, 952013

2 — Wheel, 8", 13730912

4 — Washer, 3/4"

2 — Cotter Pin

2 — Chain, 36", 678944

2 — Handle Side Plates, 36355BK

Note:

1/4"-20 x 1/2" washer-head mounting screws

for Cylinder Support, Tray, and Handle are

included with the power source.

To assemble the kit to the power source, proceed as

follows (see Fig. 1):

1. Carefully lift the power source off the floor with a

crane or hoist and remove the four orange plastic

skids from the base.

2. Assemble the two swivel casters (952013) to the

base front corners of the power source using eight

(8) 1/4"-20 x 1/2" mounting screws supplied with

the power source.

3. Mount the Tray/Axle assembly (36051) to the rear

bottom of the base using eight (8) mounting screws

supplied with the power source.

4. On each end of the axle, assemble one 3/4"

washer, an 8" wheel (13730912), another 3/4"

washer, and then insert cotter pin into the hole of

axle in that order. Bend cotter pin to secure in

place.

5. Make sure all mounting screws are firmly tight-

ened and then lower the power source to the floor.

6. Assemble the cylinder support (36353BK) to the

top end of the rear panel using four (4) mounting

screws supplied with the power source. Firmly

tighten all screws.

7. Slide at least the second link of each chain

(678944) into the center slot of the cylinder sup-

port.

8. Mount the handle side plates (35355BK) to the

side panel of the power source using the screws

supplied with the power source. Make sure the

screws are firmly tightened.

9. Mount the handle shaft using the 5/16"-18 screws

and flat washers.

When you put the cylinders in place, pull the chain

tightly around each cylinder and slide a chain link

into the outer slot of the cylinder support. Be sure

to pull the link down firmly into each slot to secure

the chain so that there is little slack of the chain

about the cylinder. DO NOT just "loop" a link over

the end of the support.

10.

Never lift a power source with cylinder(s) attached.

F-15-334

CYLINDER TRAY/AXLE

ASSY. - 36051BK

(2) WHEEL, 8" - 13730912

(2) COTTER PIN

(4) WASHER, FLAT 3/4"

NOTE: 1. 1/4" - 20 x 1/2" washer-head mounting screws are supplied with the power source.

2. First manufactured units did not include the 4 holes as shown for mounting the

cylinder support. If you have such unit, 4 5/16" (o.312") dia. holes must be drilled

through the rear panel. Use the cylinder support as a template to locate the holes.

Use 1/4"-20x5/8" long screws, lockwashers, and nuts to mount the cylinder support.

(2) SWIVEL CASTOR - 952013

HANDLE SIDE

PLATE - 36355BK

HANDLE SHAFT - 36356BK

F-15-334 4/96 3C Printed in U.S.A.

(2) 5/16"-18 x 1" SCREW

(2) 5/16" FLAT WASHER

CYLINDER SUPPORT - 36353BK (See Note 2)

(2) CHAIN, 36" - 678944 (Not Illustrated)

Fig. 1 - TR-23A Truck Kit Assembled to Power Source

ESAB TR-23A Truck Kit User manual

ESAB TR-23A Truck Kit User manual

ESAB TR-23A Truck Kit User manual

Related papers

Other documents