ESAB Dual Cylinder Rack Kit Troubleshooting instruction

Category
Car kits
Type
Troubleshooting instruction

ESAB Dual Cylinder Rack Kit

The ESAB Dual Cylinder Rack Kit is designed to securely hold and transport two gas cylinders on the ESP-100i power source. The kit includes a cylinder rack, two chains, a handle, and mounting hardware. The cylinder rack is made of durable steel and has two slots to accommodate the chains. The chains are adjustable to fit a variety of cylinder sizes. The handle is made of sturdy plastic and provides a comfortable grip for lifting and carrying the power source. The mounting hardware allows the cylinder rack to be easily attached to the ESP-100i power source.

ESAB Dual Cylinder Rack Kit

The ESAB Dual Cylinder Rack Kit is designed to securely hold and transport two gas cylinders on the ESP-100i power source. The kit includes a cylinder rack, two chains, a handle, and mounting hardware. The cylinder rack is made of durable steel and has two slots to accommodate the chains. The chains are adjustable to fit a variety of cylinder sizes. The handle is made of sturdy plastic and provides a comfortable grip for lifting and carrying the power source. The mounting hardware allows the cylinder rack to be easily attached to the ESP-100i power source.

INSTRUCTIONS for
F-15-342
July, 1996
F-15-342
DUAL CYLINDER RACK KIT
P/N 35833
FOR USE ON THE ESP-100i POWER SOURCE
This kit includes the following components (See Fig.1):
1 — Dual Cylinder Bracket, 36621
1 — Cylinder Rack, 30511
2 — Chain, 3 ft., 678944
4 — Screw, 3/8"-16 X 1" Long
4 — Lockwasher, 3/8"
4 — Flatwasher, 3/8"
8 — Screw 1/4"-20 X 1/2" Long
1 — Handle, 678402
2. Assemble the cylinder rack (35011) to the top rear
panel of the unit using four (4) 1/4-20 X 1/2" long
screws. Tighten all screws firmly with a wrench.
3. Slide at least the second link of each chain into the
center slot of the upper cylinder bracket.
4. Mount the handle to the top front of the ESP-100i
power source as illustrated, using four (4) 1/4-20 X 1/
2" screws.
When you put the cylinders in place, pull the chain tightly
around each cylinder and slide a chain link into the outer
slot of the cylinder support. Be sure to pull the link down
firmly into each slot to secure the chain so that there is
little slack of the chain about the cylinder. DO NOT just
"loop" a link over the end of the rack.
Never lift a power source with cylinder(s) attached.
Be sure this information reaches the operator.
You can get extra copies through your supplier.
F-15-342 7/96 3C Printed in U.S.A.
(2) CHAIN, 36"
- 678944
CYLINDER RACK
SUPPORT - 30511
BRACKET, 2-Cyl. - 36621
(4) SCREW, 3/8-16 X 1"
(4) WASHER, 3/8"
(4) LOCKWASHER, 3/8"
(4) SCREW, 1/4-20 X 1/2", WASHER HEAD
(4) SCREW, 1/4-20 X 1/2", WASHER HEAD
To assemble the kit to the ESP-100i power source, re-
fer to Figure 1 and proceed as follows:
1. Assemble the dual cylinder bracket assembly (36621)
to the base of the rear side of the power source using
four (4) sets of 3/8"-16 X 1" long screws, lockwashers,
and washers. Tighten the screws firmly with a wrench.
Fig. 1 - Mounting Dual Cylinder Rack Kit Components to ESP-100i Power Source
HANDLE - 678402
HANDLE - 678402
(4) SCREW, 3/8-16 X 1"
(4) WASHER, 3/8"
(4) LOCKWASHER, 3/8"
(4) SCREW, 1/4-20 X 1/2", WASHER HEAD
(4) SCREW, 1/4-20 X 1/2", WASHER HEAD
CYLINDER RACK
SUPPORT - 30511
(2) CHAIN, 36"
- 678944
BRACKET, 2-Cyl. - 36621
F-15-342 7/96 5C Printed in U.S.A.
Fig. 1 - Mounting Dual Cylinder Rack Kit Components to ESP-100i Power Source
  • Page 1 1
  • Page 2 2

ESAB Dual Cylinder Rack Kit Troubleshooting instruction

Category
Car kits
Type
Troubleshooting instruction

ESAB Dual Cylinder Rack Kit

The ESAB Dual Cylinder Rack Kit is designed to securely hold and transport two gas cylinders on the ESP-100i power source. The kit includes a cylinder rack, two chains, a handle, and mounting hardware. The cylinder rack is made of durable steel and has two slots to accommodate the chains. The chains are adjustable to fit a variety of cylinder sizes. The handle is made of sturdy plastic and provides a comfortable grip for lifting and carrying the power source. The mounting hardware allows the cylinder rack to be easily attached to the ESP-100i power source.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI