NCR 7409-K566 Kit Instructions

Brand: NCR

Model: 7409-K566

Type: Kit Instructions

7409‐K566

SwivelMountBracket

KitInstructions



IssueA

Revision Record

Issue Date Remarks

A Aug2010 Firstissue

 



7409-K566 1

Introduction

ThiskitcontainsaswivelmountforaterminalmountedonaFixed

AngleMount(7409‐K035).Wheninstalledonacheckstandthedevice

canberotatedupto340degrees.

ThesectionsthatfollowdescribehowtoinstalltheSwivelMount

Bracketinacheckstandhowtoinstall

aFixed‐AngleMountonthe

SwivelMountBracket.

Kit Contents

Screw, Socket Cap,

1/4-20 x 2", Flat Hd

006-8608261

7402 Locking Swivel Mount

497-0443897

Pipe Nut Plate

497-0434264

Screw, 6-32 x 0.25

Phillips Hex Waaher

006-8611197

Rear Cover

497-0468273

Screw, 8-32 x 0.25,

Phillips, Truss Hd

006-8616058

Fixed Angle Mount (7409-K035)

(for Reference Only)



2 7409-K566

Mount Dimensions

18468

Rests on

Checkstand

Surface

134 mm

(5.28 in.)

72 mm

(2.83 in.)



7409-K566 3

Installing the Swivel Mount Bracket

1. Inthedesiredlocation,drillan88.9mm(3.5ʺ)holeinthetopofthe

checkstandfortheSwivelMountBracket.

7 mm x4

(.277 in.)

18465

88.9 mm

(3.5 in.)



2. PlacetheSwivelMountBracketintothehole.

4 7409-K566

3. Asshowninthefollowingillustration,themaximumrotationis340

degrees.Makingsurethattheterminalcanrotatetothedesired

positions,markthecheckstandthroughthefourscrewholesinthe

flange.

Note: Themaximumrotationis340degrees.Thisleavesa20

degreeʺDeadZoneʺthroughwhich

theswivelcannotrotateand

thedisplaycannotbevieweddirectly.ThecenteroftheʺDead

Zoneʺisalways90degreesfromthetabintheflange.Keepthisin

mindwhenplanningtheinstallationandmarkingthecheckstand

throughthefourscrewholes.

Maximum rotation

is 340 degrees

18499

Tabs for securing

Fixed-Angle Mount

Display faces this side

Flange

Dead Zone

(20 Degrees)



4. RemovetheSwivelMountBracketanddrillfour7mm(.277ʺ)holes

inthemarkedlocations.

5. PlacetheSwivelMountBracketintotheholeinthecheckstand.

7409-K566 5

6. UsetheRetainingRingandthefourMountingScrewstosecurethe

SwivelMountBrackettothecheckstand.

18498

Mounting Screws (4)

Retaining Ring

Checkstand



6 7409-K566

Installing a Fixed-Angle Mount on the Swivel Mount Bracket

1. AligntheslotsinthebottomoftheFixed‐AngleMountwiththe

LockingTabsontheSwivelMountBracket.LocktheFixed ‐Angle

Mountinplacebyslidingittoward therearoftheSwivelMount

Bracket.

Securing Screws

Locking Tabs

18496

Fixed-Angle Mount



7409-K566 7

2. UsethetwoSecuringScrewstosecuretheFixed‐AngleMountto

theSwivelMountBracket.

3. Insertthetwotabs ontheCoverintothetwolowerslotsonthe

backoftheFixed‐AngleMount.

17744

Cover



4. FrominsidetheFixed‐AngleMount,securetheCoverwithscrews

andwashers(2).

NCR 7409-K566 Kit Instructions

NCR 7409-K566 Kit Instructions

NCR 7409-K566 Kit Instructions

Related papers

Other documents